RMNCTS-ICOMIR PIO

1 CTS-ICOM-AA01 (EQ-PIO) CTS-ICOM-AB01 (OHT-PIO) * The wireless equipment concerned can result in jamming during operation. 2014. 3. 11 ( Ver 0.9 ) IR-PIO SPECIFICATION 2 FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: RMNCTS-ICOM WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF EXPOSURE WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 3 [ Table of Contents ] 1. Product Outline 2. Product Feature 3. Wireless Communication Characteristics 4. IR Communication Characteristics 5. Product Code Configuration 6. IR Radiation Characteristics 7. Antenna Radiation Characteristics 8. Input/output Circuit 9. Product Specification 10. Tool Specification 11. Connector Connection Specification 12. LED Display Content 13. Major Pin Function 14. ID & CH Setting Method 15. RF Consideration When Installing a PIO 4 1. Product Outline The CTS-ICOM Series is an IR communication device used to give and receive 8-bit data in a non-contact type, and is a product with various convenient functions using a 2.4GHz wireless communication technology. This device is used to give and receive a SEMI-E84/E23 protocol or maximum 8-bit input/output data wirelessly for an exchange of control signals mainly between an AGV or OHT(Master or Active device), etc. and equipment(Slave or Passive device). This is a product to grasp causes quickly and establish measures easily by providing various functions to analysis the causes in case of an abnormality in data given and received during use. 2. Product Feature  IR communication : For giving and receiving input/output data  2.4GHz wireless communication : Additional function such as downloading of transmission/reception data and F/W, etc.  The wireless communication operating distance is maximum 5M (However, there shall be no obstacles to electromagnetic waves in the middle.)  Designation of a wireless communication ID(address) : 6 digits (hexadecimal code)  For 8-bit input/output signals  Storage of various information using a large-capacity SRAM : About 200 pieces of work such as communication data, absolute time, reception signal intensity, etc. (Erased when power is OFF)  Serial communication port : Setting change, communication data information receiving, F/W downloading, etc. 3. Wireless Communication Characteristics  RF communication using a 2.4GHz ISM(Industrial, Scientific and Medical) band that can be used without permission  Equipment name: Wireless device for a wireless data communication system  High-speed data communication of 1Mbps per channel  GFSK modulation type, 1MHz bandwidth 5  Superior expandability with an optional function of 6-byte serial number and 2-byte frequency  200uS or less channel switching time to minimize interference with other wireless devices  Possibility of frequency interference with 2.4GHz Bluetooth and wireless communication devices  RF maximum output power : 0dBm  Sensitivity of the reception part : -90dBm 6 4. IR Communication Characteristics  Wavelength : 870nm (infrared ray)  Ambient brightness : 4000lx or less incandescent lamp and fluorescent lamp, where there is no direct sunshine  Transmission and reception method : Half Duplex  Modulation method : Pulse Modulation  Operating distance and angle : 0.5m at 0°, 0.25m at ±15°  Communication distance regulation : Serial communication command  Reception level regulation : For serial communication command and ambient light noise removal  Input signal and GO output filtering function : 0 th ~ 10 th (Serial communication command) 5. Product Code Configuration Item name Feature CTS-ICOM-AA01-xx-y-zz (EQ, Slave) 25-pin DSUB, Male Type (For equipment) CTS-ICOM-AB01-xx-y-zz (OHT, Master) Hirose 26-pin, HIF6-26D-1.27R (For OHT, AGV) *) xx : The communication distance and unit are 0.1m, 05=0.5m, 10=1.0m *) y : Transmission and reception window position, T=Top View, F=Front View *) zz : The cable length and unit are 0.1m, 25=2.5m 7 6. IR Radiation Characteristics As shown in the figure below, the communicable angle is 30°, and communication is possible from a 0.25m away distance at ±15° and from a 0.5m away distance at 0°. If lighting, s…

Text truncated - open the document above for the full version.

CanTops #A-1208, Digital Empire, 16, Deogyeong-daero 1556 beon-gil, Yeongtong-gu, Suwon-si, Gyeonggi-do, South Korea Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: Mar 12, 2015 SUBJECT: FCC Application for (FCCID: RMNCTS-ICOM) To Whom It May Concern: We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Regards, Sang-Kyo Ahn / Manager ─────────────

Date : Jan. 10, 2014 Rev : 2.1 HACS-F003 FCC Confidentiality Request Letter HCT America LLC ([email protected]) 44364 S. Grimmer Blvd. Fremont, CA 94538 TEL: +1.510.933.8848, Fax: +1.510.933.8849 Page 1 of 2 This document is electronically controlled. Hard copy documents are uncontrolled. Please check all hard copies against the controlled electronic copy to ensure validity. This document is the confidential property of HCT America LLC. It may not be forwarded or reproduced in whole or in part without written permissions from HCT America LLC FCC Confidentiality Request Letter HACS-F003 FCC Confidentiality Request Letter Rev : 2.1 DATE : 3/13/2015 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD SUBJECT : Request for Confidentiality for FCC ID : RMNCTS-ICOM We hereby request confidential treatment of the information accompanying this application as outlined below: LONG-TERM AND SHORT-TERM CONFIDENTIAL LIST LONG-TERM CONFIDENTIAL Exhibit Description 1 Block Diagram 2 Schematics 3 Operational Description 4 SHORT-TERM CONFIDENTIAL ( DAYS) 5 6 7 8 The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Sang-Kyo Ahn Signed by: Company Name : CanTops Company Address : A-1208 Digital Empire, 16, Deogyeong-daero 1556 beon-gil, Yeongtong-gu, Suwon-si, Gyeonggi-do Contact Person Name/Title (in print) : Sang-Kyo/General Manager

FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 3. External Photos of EUT Page Number : Page 1 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Appendix 3. External Photographs of EUT Front Back FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 3. External Photos of EUT Page Number : Page 2 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Right Left FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 3. External Photos of EUT Page Number : Page 3 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Top Bottom

FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 2. FCC ID Label and location Page Number : Page 1 to 1 BWS TECH Inc. Issue Date : February 06, 2015 Appendix 2. FCC ID Label and location Product Label Sample with FCC ID Label information and location Following is a sample copy of the label that will be placed on the rear cabinet of the product. The FCC identifier is marked in the product label. CanTops Product Name: IR PIO Model Name: CTS-ICOM-AA01-05-T-250 FCC ID: RMNCTS-ICOM This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label Location The label shown above shall be permanently affixed at a conspicuous location(cabinet out side) on the device and be readily visible to the user at the time purchase.(Labeling requirements per 2.925) FCC ID LABEL & Caution

FCC ID: RMNCTS-ICOM CanTops IRPIO/CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 4. Internal Photos of EUT Page Number : Page 1 to 2 BWS TECH Inc. Issue Date : February 06, 2015 Appendix 4. Internal Photographs of EUT Main Board Front FCC ID: RMNCTS-ICOM CanTops IRPIO/CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 4. Internal Photos of EUT Page Number : Page 2 to 2 BWS TECH Inc. Issue Date : February 06, 2015 Main Board Front FCC ID: RMNCTS-ICOM CanTops IRPIO/CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 4. Internal Photos of EUT Page Number : Page 3 to 2 BWS TECH Inc. Issue Date : February 06, 2015 Main Board Back FCC ID: RMNCTS-ICOM CanTops IRPIO/CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 4. Internal Photos of EUT Page Number : Page 4 to 2 BWS TECH Inc. Issue Date : February 06, 2015 Main Board Back FCC ID: RMNCTS-ICOM CanTops IRPIO/CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 4. Internal Photos of EUT Page Number : Page 5 to 2 BWS TECH Inc. Issue Date : February 06, 2015 Internal

FCC ID: RMNCTS-ICOM CanTop IR PIO /CTS-ICOM-AA01-05-T-250 RF Exposure Report Issue Date : February 06, 2015 Appendix 11. RF Exposure Requirement 1.Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength(V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 - - F/300 6 1500-100,000 - - 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 - - F/1500 6 1500-100,000 - - 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r2) Where Pd = power density in mW/ 2 cm Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/ 2 cm . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 2.Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 23°Cand 42％ RH. FCC ID: RMNCTS-ICOM CanTop IR PIO /CTS-ICOM-AA01-05-T-250 RF Exposure Report Issue Date : February 06, 2015 3.Test Result of RF Exposure Evaluation Operating mode Frequency RF Output Power(dBm) GFSK 2403 -1.2 GFSK 2441 -1.3 GFSK 2480 -1.2 Maximum RF Power=-1.2dBm+3.0dBi=1.8dBm=1.51mW 1.51/(4*3.14*400)=0.0003 Frequency Band(MHz)Maximum RF Power(mW) Power Density at R = 20cm(mW/ 2 cm) 2403-2480 1.51 0.0003 Note: The power density Pd (4th column) at a distance of 20 cm calculated from the Friis transmission formula is far below the limit of 1 mW/ 2 cm.

FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 FCC Test Report Page Number : 2 of 39 BWS TECH Inc. Data of Issue : March 13, 2015 TABLE OF CONTENTS 1. General Information................................................................... 3 2. Description of Test Facility......................................................... 4 3. Test Methodology...................................................................... 5 4. Summary of Test Results............................................................ 6 5. Test Data.................................................................................. 7 5.1 6dB Bandwidth..................................................................... 7 5.2 Maximum Peak Conducted Output Power................................ 9 5.3 Power Spectral Density.......................................................... 10 5.4 Conducted Spurious Emission............................................... 12 5.5 Radiated Spurious Emission.................................................. 16 5.6 Band Edge Measurement....................................................... 22 5.7 AC Power Conducted Emission.............................................. 31 5.8 Antenna Application............................................................. 39 FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 FCC Test Report Page Number : 3 of 39 BWS TECH Inc. Data of Issue : March 13, 2015 FCC TEST REPORT Scope – Measurement and determination of electromagnetic emission(EME) of radio frequency devices including intentional radiators and/or unintentional radiators for compliance with the technical rules and regulations of the U.S Federal Communications Commission(FCC) 1. General Information 1.1 Applicant 1.2 Manufacturer 1.3 Eut Description  EUT Type : IR PIO  Model Name : CTS-ICOM-AA00-05-T-250, CTS-ICOM-AA01-05-T-030 CTS-ICOM-AA01-05-T-150, CTS-ICOM-AA01-05-T-250 CTS-ICOM-AB00-05-F-250, CTS-ICOM-AB01-05-F-045 CTS-ICOM- AB02-05-F-060  S/N : Prototype  Freq. Range : 2403-2480 MHz  Number of Channels : 78  Modulation Method : GFSK  Input Voltage : DC 24 V ±10%  Antenna Peak Gain : 3 dBi 1.4 Other Information  FCC Rule Part(s) : Part 15 Subpart C §15.247  FCC ID : RMNCTS-ICOM  Test Procedure : ANSI C63.10-2013 KDB 558074 D01 DTS Meas Guidance v03r02  Date of Test :January 07, 2015 to March 12, 2015  Place of Test : BWS TECH Inc.(FCC Registration Number : 287786) #23, Gokhyeon-ro 480 Beon-gil, Mohyeon-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do 449-853, South Korea TEL: +82 31 333 5997 FAX: +82 31 333 0017  Company Name : CanTops  Company Address : A-1208 Digital Empire,16, Deogyeong-daero 1556 beon-gil, Yeongtong-gu, Suwon-si, Gyeonggi-do 443-702, South Korea  Phone/Fax : Tel No. : +82-31-303-5234 Fax No. : +82-31-303-5233  Company Name : CanTops  Company Address : A-1208 Digital Empire,16, Deogyeong-daero 1556 beon-gil, Yeongtong-gu, Suwon-si, Gyeonggi-do 443-702, South Korea  Phone/Fax : Tel No. : +82-31-303-5234 Fax No. : +82-31-303-5233 FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 FCC Test Report Page Number : 4 of 39 BWS TECH Inc. Data of Issue : March 13, 2015 2. Description of Test Facility Site Description Test Lab. : Accredited by Industry Canada, February 27, 2012 The Certificate Registration Number is 4963A-2. Accredited by FCC, September 03, 2013 The Certificate Registration Number is 287786. Accredited by VCCI, July 10, 2012 The Certificate Registration Number is C-4326 Accredited by RRA(EMC,RF, SAR), November 27, 2014 The Certificate Registration Number is KR0017 Accredited by KOLAS(KS Q ISO/IEC 17025), October 7, 2014 The Certificate Registration Number is KT174 Name of Firm : BWS TECH Inc. Site Location : #23, Gokhyeon-ro 480 Beon-gil, Mohyeon-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do 449-853, South Korea FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 FCC Test Report Page Number : 5 of 39 BWS TECH Inc. Data of Issue : March 13, 2015 3. Test Methodology The tests documented in this report were performed in accordance with ANSI C63.10: 2013 and FCC CFR 47 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.247. 3.1 EUT Configuration The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application 3.2 EUT Exercise The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 3.3 FCC Part 15.205 Restricted Bands Of Operations (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.4 Description Of Test Modes The EUT has been tested under operating condition. After verification, all tests were carried out with the worst case test modes as shown below GFSK(1Mbps) Channel Low (2403MHz), Mid (2442MHz) and High (2480MHz), these were chosen for full testing. FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-A…

Text truncated - open the document above for the full version.

FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 1. Test Setup Photos Page Number : Page 1 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Appendix 1. Test Setup Photos Radiated Test(0.009-30MHz) FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 1. Test Setup Photos Page Number : Page 2 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Radiated Test(30-1000MHz) FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 1. Test Setup Photos Page Number : Page 3 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Radiated Test(Above 1GHz) FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 1. Test Setup Photos Page Number : Page 4 to 5 BWS TECH Inc. Issue Date : February 06, 2015 Conducted Test(2403~2480MHz) FCC ID: RMNCTS-ICOM CanTops IR PIO / CTS-ICOM-AA01-05-T-250 Report No: BWS-15-RF-0002 Appendix 1. Test Setup Photos Page Number : Page 5 to 5 BWS TECH Inc. Issue Date : February 06, 2015 AC Power Conducted Emission(0.15-30MHz)