RTX-Q7G2.4G Wireless Mouse

Installing the Batteries 2.4GHZ Wireless mouse use tow AA alkaline batteries, Installing Batteries in the Mouse Step1. Open the battery compartment. Step2. Insert the batteries as shown inside the battery compartment. Step3. Replace the cover. The receiver is connected to your computer via USB port USB cable. And it plug to USB port of your computer. CAUTION: Windows 98 or higher is required for USB port installation. Connect the receiver cable to the USB port on computer. For Windows, you may be prompted to insert the windows software CD. Insert this software CD into the computer’s CD-ROM driver when asked to do so. Then follow the on-screen instructions. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Software installation The driver supports Win98/SE , Win2000 and Win XP. Vista The driver will install automatically if the auto-run is enable in your computer. Otherwise, you can manually launch the installation by double clicking the file setup.exe in the CD-ROM. The setup applet s icon of the keyboard and the mouse will appear on the windows taskbar after successfully completing software installation. You can double click or right click the applet, and setup the functions of your preferred selection for both keyboard and mouse to enhance your device Model:O7G Instruction Manual 2.4GHZ RF & Optical Mouse CAUTION: To use this device properly, please read the user’s guide before installation. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Indicators on Receiver 1． Super mini USB receiver,just plug it and It works 2． The storable 2.4Ghz micro-receiver and An all-terrain optical engine complete the Feature mouse waining 1: Do not disassemble the product or remove any parts 2: Do not put the product into water or any liquid. Should this happen, take the product off computer and contact your vendor or after-sales service center for maintenance. 3: Do not plug and/or unplug the receiver with wet hands to avoid electric shock. 4: Do not put the product close to heat source, or expose it to high temperature. 5: Do not put the product where the electromagnetic wave is strong. Strong electromagnetic wave will cause damage to the product or internal data. Standard parameters of mouse emitter 1:Working frequency 2.4GHz 2:Working voltage DC3V 3: Working current 5mA 3: sleep current :80uA 4: Sleep time :8Min 5:15metres operation distance

Comat Electronic (Shenzhen) Co., Ltd. August 22, 2012 To: SIEMIC, INC. 775 Montague Expressway Milpitas , CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ______ Comat Electronic (Shenzhen) Co., Ltd. ___hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Description: 2.4G Wireless Mouse Model name: Q7G FCC ID: RTX-Q7G We affirm that between SIEMIC and __ Comat Electronic (Shenzhen) Co., Ltd. ___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature: Client’s name / title: Xiaowen Zhang / General Manager Contact information / address: No.2 Lane 1, Xin’an 3 rd 28 District, Baoan, Shenzhen, China

SCS-F19: Confidentiality Request Letter Page 1 of 1 Rev 2.0 Comat Electronic (Shenzhen) Co., Ltd. August 22, 2012 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: RTX-Q7G We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Client’s signature: Client’s name / title: Xiaowen Zhang / General Manager Contact information / address: No.2 Lane 1, Xin’an 3 rd 28 District, Baoan, Shenzhen, China

100% FCC ID: RTX-Q7G A Q7G 150% Explain: 1. Specification:36*69.5mm 2. Print：White on Black 3.Material：Transparent shift dragon stickers 4. Client：United States 5.Orders： Affixed to the bottom of the mouse inside the box This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. FCC ID: RTX-Q7G This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. The FCC Safety regulations stickers FCC Certification label Sample

FCC Certification Label Location Sample Label location

Antenna

Page 1 of 52 FCC ID: RTX-Q7G ACCURATE TECHNOLOGY CO. LTD REPORT NO. ATE20121911 FCC CERTIFICATION On Behalf of Comat Electronic (Shenzhen) Co., Ltd. 2.4G Wireless Mouse Model No.: Q7G FCC ID: RTX-Q7G Prepared for : Comat Electronic (Shenzhen) Co., Ltd. Address : No.2 Lane 1, Xin’an 3 rd 28 District, Baoan, Shenzhen, China Prepared by : ACCURATE TECHNOLOGY CO. LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20121911 Date of Test : August 17-31, 2012 Date of Report : August 31, 2012 Page 2 of 52 FCC ID: RTX-Q7G ACCURATE TECHNOLOGY CO. LTD REPORT NO. ATE20121911 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 4 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Description of Test Facility ......................................................................................................................4 1.3. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3. SUMMARY OF TEST RESULTS................................................................................................... 7 4. FUNDAMENTAL AND HARMONICS RADIATED EMISSION FOR SECTION 15.249(A) 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. The Emission Limit ..................................................................................................................................9 4.3. Configuration of EUT on Measurement ...................................................................................................9 4.4. Operating Condition of EUT ....................................................................................................................9 4.5. Test Procedure ........................................................................................................................................10 4.6. The Field Strength of Radiation Emission Measurement Results ..........................................................11 5. SPURIOUS RADIATED EMISSION FOR SECTION 15.249(D) ............................................. 14 5.1. Block Diagram of Test Setup..................................................................................................................14 5.2. The Emission Limit For Section 15.249(d) ............................................................................................14 5.3. EUT Configuration on Measurement .....................................................................................................15 5.4. Operating Condition of EUT ..................................................................................................................15 5.5. Test Procedure ........................................................................................................................................16 5.6. The Emission Measurement Result ........................................................................................................17 6. BAND EDGES ................................................................................................................................. 20 6.1. The Requirement ....................................................................................................................................20 6.2. EUT Configuration on Measurement .....................................................................................................20 6.3. Operating Condition of EUT ..................................................................................................................20 6.4. Test Procedure ........................................................................................................................................20 6.5. The Measurement Result ........................................................................................................................21 7. ANTENNA REQUIREMENT........................................................................................................ 23 7.1. The Requirement ....................................................................................................................................23 7.2. Antenna Construction .............................................................................................................................23 APPENDIX I ( TEST CURVES) (28 pages) Page 3 of 52 FCC ID: RTX-Q7G ACCURATE TECHNOLOGY CO. LTD REPORT NO. ATE20121911 Test Report Certification Applicant : Comat Electronic (Shenzhen) Co., Ltd. Manufacturer : Comat Electronic (Shenzhen) Co., Ltd. EUT Description : 2.4G Wireless Mouse (A) MODEL NO.: Q7G (B) POWER SUPPLY: 3V DC (“AA” batteries 2×) Measurement Procedure Used: FCC Rules and Regulations Part 15 Subpart C Section 15.249 ANSI C63.4: 2009 The device described above is tested by ACCURATE TECHNOLOGY CO. LTD to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart C Section15.249 limits. The measurement results are contained in this test report and ACCURATE TECHNOLOGY CO. LTD is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of ACCURATE TECHNOLOGY CO…

Text truncated - open the document above for the full version.

Radiated emissions test < 30MHz Radiated emissions test 30MHz- 1GHz Radiated emissions test > 1GHz