
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Page 21 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 22 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 23 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 24 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 25 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 26 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 27 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 28 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 29 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 30 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 The antenna(s) used for this transmitter must be installed to provide a separating distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERβS AUTHORITY TO OPERATE THE EQUIPMENT.
Page 13 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Block Diagram
Page 6 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Photographs Figure 1 General Appearance Figure 2 General Appearance Label Location Page 7 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Figure 3 General Appearance Figure 4 General Appearance Page 8 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Figure 5 General Appearance Figure 6 General Appearance
Page 6 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Photographs Figure 1 General Appearance Figure 2 General Appearance Label Location
Page 4 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Label Drawing Please refer Exhibit 2 Figure 2 for Label Placement Location FCC ID: S3HPB041670300 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 9 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Figure 7 Main Board, Component Side Figure 8 Main Board, Component Side Page 10 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Figure 9 Main Board, Component Side Figure 10 Main Board, Component Side Page 11 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Figure 11 Main Board, Component Side
Page 19 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300
Page 15 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300 Page 16 Amplus Industrial Ltd. RS232 RF Module FCC ID : S3HPB041670300
FCC ID:S3HPB041670300 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F05079 APPLICATION FOR CERTIFICATION On Behalf of Amplus Industrial Ltd. RS232 RF Module Model Number: PB041670300 Prepared for : Amplus Industrial Ltd. Room.B.20/F Leahander Centre, 28 Wang Wo Tsai Street, Tsuen Wan, N.T., H.K. Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park, Nantou, Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number οΌ ACS-F05079 Date of Test οΌ Feb.23~Mar.16, 2005 Date of Report οΌ Mar.18, 2005 FCC ID:S3HPB041670300 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F05079 TABLE OF CONTENTS Description Page FCC Test Report for Declaration of Conformity 1. GENERAL INFORMATION .................................................................................................... 1-1 1.1. Description of Device (EUT) .............................................................................................................1-1 1.2. Tested Supporting System Details .....................................................................................................1-2 1.3. Test Facility........................................................................................................................................1-3 1.4. Measurement Uncertainty ..................................................................................................................1-3 2. POWER LINE CONDUCTED EMISSION TEST.................................................................. 2-1 3. RADIATED EMISSION TEST ................................................................................................. 3-1 3.1. Test Equipment ..................................................................................................................................3-1 3.2. Block Diagram of Test Setup .............................................................................................................3-1 3.3. Radiated Emission Limit ....................................................................................................................3-2 3.4. EUT Configuration on Test................................................................................................................3-3 3.5. Operating Condition of EUT..............................................................................................................3-3 3.6. Test Procedure....................................................................................................................................3-3 3.7. Radiated Emission Test Result...........................................................................................................3-4 4. BAND EDGES MEASUREMENT............................................................................................ 4-1 4.1. Test Equipment ..................................................................................................................................4-1 4.2. Block Diagram of Test Setup .............................................................................................................4-1 4.3. Test Standard......................................................................................................................................4-1 4.4. Bandwidth Limit ................................................................................................................................4-1 4.5. Test Procedure....................................................................................................................................4-1 5. DEVIATION TO TEST SPECIFICATIONS .......................................................................... 5-1 6. PHOTOGRAPH.......................................................................................................................... 6-1 6.1. Photos of Radiated Emission Test (In Anechoic Chamber)...............................................................6-1 6.2. Photo of Band Edges Measurement ...................................................................................................6-2 APPENDIX I (17 pages) FCC ID:S3HPB041670300 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F05079 TEST REPORT DECLARATION Applicant οΌ Amplus Industrial Ltd. Manufacturer οΌ Amplus Industrial Ltd. EUT Description οΌ RS232 RF Module (A) MODEL NO. : PB041670300 (B) SERIAL NO. : F2005031801 (C) POWER SUPPLY : DC 5V with PC AC 120V/60Hz Test Procedure Used: FCC Rules and Regulations Part 15 Subpart C Apr, 2004. The device described above is tested by AUDIX TECHNOLOGY (SHENZHEN) CO., LTD. to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart C limits both radiated and conducted emissions. The test results are contained in this test report and AUDIX TECHNOLOGY (SHENZHEN) CO., LTD. is assumed full responsibility for the accuracy and completeness of these tests. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of AUDIX TECHNOLOGY (SHENZHEN) CO., LTD. This report must not be used by the applicant to claim product endorsement by NVLAP or any agency of the U.S. Government. Date of Test : Feb.23~Mar.16, 2005 Prepared by : Reviewer : Approved & Authorized Signer : Name of the Representative of the Responsible Party : Signature : FCC ID:S3HPB041670300 p age 1-1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F05079 1. GENERAL INFORMATION 1.1. Description of Device (EUT) Description : RS232 RF Module Model Number : PB041670300 Applicant : Amplus Industrial Ltd. Room.B.20/F Leahander Centre, 28 Wang Wo Tsai Street, Tsuen Wan, N.T., H.K. Manufacturer : Amplus Industrial Ltd. No.8 Ming Leung Road, Zhuliao Town, Baiyun Guangzhou, China Date of Test : Feb.23~Mar.16, 2005 FCC ID:β¦
Text truncated - open the document above for the full version.
FCC ID:S3HPB041670300 p age 6-1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F05079 6. PHOTOGRAPH 6.1. Photos of Radiated Emission Test (In Anechoic Chamber) FCC ID:S3HPB041670300 p age 6-2 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F05079 6.2. Photo of Band Edges Measurement
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 913 MHz - 919 MHz | - |

Multisport tabletop scoreboard (remote)
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter