S7A-SP12BLUETOOTH STEREO MOTORCYCLE HEADSET

| EXPAND 1 EXPAND Bluetooth Stereo Headset & Intercom SENA www.senabluetooth.com User’s Guide | EXPAND 2 1. POWERING ON/OFF AND CHARGING 1.1 Powering On Press the Center Button and the (+) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 1.2 Powering Off Tap the Center Button and the (+) Button simultaneously (you don’t need to press and hold in order for the system to power off). The red LED turns on for about 2 seconds until it turns off completely and you will hear “Goodbye” and descending beeps. 1.3 Charging The charging LED beside the charging port turns on red while charging, and turns to blue when the headset is fully charged. It takes about 2.5 hours to be completely charged. You can use the EXPAND while charging. It is especially helpful when you use a cigarette charger for a long road trip. 1.4 Low Battery Warning When the battery is low, the blinking blue LED in stand-by mode turns to red and you will hear mid-tone triple beeps and a voice prompt, “Low battery”. 1.5 Checking the Battery Level You can check the battery level in two different ways when the headset is powering on. 1.5.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 1.5.2 Voice Prompt Indicator When you power on the headset, keep pressing the Center Button and the (+) Button simultaneously for several seconds until you hear high tone triple beeps. Then you will hear voice prompt indicating the battery level. However, if you release the buttons as soon as the headset turns on, you will not hear the voice prompt of battery level indication. 2. Volume Adjustment | EXPAND 3 You can easily adjust the volume by tapping the (+) Button or the (-) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music. So you can always maintain the preferred optimum volume level for each audio source. 3. EXPAND CONFIGURATION SETTING You can set the configuration of the EXPAND by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Center Button for 10 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt, “Configuration menu”. 2. Tap the (+) Button or (-) Button to navigate between the menus. You will hear voice prompts for each menu items as below. 3. You can enable / disable the feature or execute the command by tapping the Center Button. 4. If you want to exit the configuration immediately, tap the (+) Button or (-) Button until you hear a voice prompt, “Exit configuration”, then tap the Center Button. The voice prompt for each menu item is as follows: (1) Phone pairing (2) Multipoint pairing (3) Phone selective pairing (4) Media Selective pairing (5) VOX phone (6) VOX intercom (7) VOX sensitivity (8) Voice prompt (9) Delete all pairings (10) Factory reset (11) Exit configuration 3.1 Mobile Phone Pairing Voice Prompt “Phone pairing” Factory Default N/A | EXPAND 4 To go into mobile phone pairing mode, tap the (+) Button or the (-) Button until you hear a voice prompt, “Phone pairing”. Please refer to section 7.1 for details on mobile phone pairing. If you tap the (+) or (-) Button, you can exit from the phone pairing mode. 3.2 Multipoint Pairing Voice Prompt “Multipoint pairing” Factory Default N/A To go into multipoint pairing mode, tap the (+) Button or the (-) Button until you hear a voice prompt, “Multipoint pairing”. Please refer to section 7.2 for details on multipoint pairing. If you tap the (+) or (-) Button, you can exit from the multipoint pairing mode. 3.3 Phone Selective Pairing Voice Prompt “Phone selective pairing” Factory Default N/A To go into phone selective pairing mode, tap the (+) Button or the (-) Button until you hear a voice prompt, “Phone selective pairing”. Please refer to section 8 for more details on phone selective pairing. If you tap the (+) or (-) Button, you can exit from the phone selective pairing mode. 3.4 Media Selective Pairing Voice Prompt “Media selective pairing” Factory Default N/A To go into media selective pairing mode, tap the (+) Button or the (-) Button until you hear a voice prompt, “Media selective pairing”. Please refer to section 8 for more details on media selective pairing. If you tap the (+) or (-) Button, you can exit from the media selective pairing mode. 3.5 Enabling/Disabling Voice Activated Phone Answering Voice Prompt “VOX phone” Factory Default Enable | EXPAND 5 Enable / Disable Tap the Center Button Tap the (+) Button or the (-) Button until you hear a voice prompt, “VOX phone”. If this feature is enabled, you can answer incoming calls by simply saying a word loudly enough, unless you are connected to intercom. For example, when you hear a series of beeps for an incoming call, you can answer the phone by saying “Hello” or any other word loudly. However, the phone VOX feature does not work if you are connected to intercom. This is enabled from the factory but you can disable this. If this mode is disabled, you have to tap the Center Button to answer an incoming call. 3.6 Enabling/Disabling Voice Activated Intercom Voice Prompt “VOX intercom” Factory Default Disable Enable / Disable Tap the Center Button Tap the (+) Button or the (-) Button until you hear a voice prompt, “VOX intercom”. If this feature is enabled, you can initiate an intercom conversation with the last connected intercom friend by speaking any word loudly enough. If you start an intercom conversation by VOX, the intercom terminates automatically when you and your intercom friend remain silent for 20 seconds. 3.7 S…

Text truncated - open the document above for the full version.

Sena Technologies, Inc. 210 Yangjae-dong Seocho-gu Seoul 137-130 Korea Tel. +82-2-573-7772 Fax +82-2-573-7710 December 20, 2013 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 LETTER OF AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize LTA Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization for FCC ID: S7A-SP12. including signing of all documents relating to these matters. Any and all acts carried out by LTA Co., Ltd., on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Sena Technologies, Inc. LTA Co.,LTD. (Contact Person) Contact name: Jae-Ho Lee Position: Manager Phone:(82)31-323-6008 E-mail: [email protected] SeungHyun, Kim / Associate Research Engineer Sena Technologies, Inc.

Sena Technologies, Inc. 210 Yangjae-dong Seocho-gu Seoul 137-130 Korea Tel. +82-2-573-7772 Fax +82-2-573-7710 December 20, 2013 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 In re : Sena Technologies, Inc. FCC ID : S7A-SP12 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Sena Technologies, Inc.. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Sena Technologies, Inc.. temporary confidentiality of commercially sensitive information prior to product release. The requested Confidential and Temporary Confidential exhibits are listed as follows: Exhibit Type File Name CONFIDENTIAL Schematics CONF APPENDIX S7A-SP12 SCH DIA.pdf Parts list CONF APPENDIX S7A-SP12 PL.pdf Block diagram CONF APPENDIX S7A-SP12 BLK DIA.pdf Operational description CONF APPENDIX S7A-SP12 OpDes.pdf SHORT-TERM CONFIDENTIAL External Photos SHORT-TERM CONF S7A-SP12 EXT Photo.pdf Internal Photos SHORT-TERM CONF S7A-SP12 INT Photo.pdf Test-Setup Photos SHORT-TERM CONF S7A-SP12 Test Photo.pdf User’s Manual SHORT-TERM CONF S7A-SP12 Manual.pdf The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. SeungHyun, Kim / Associate Research Engineer Sena Technologies, Inc.

Sena Technologies, Inc. 210 Yangjae-dong Seocho-gu Seoul 137-130 Korea Tel. +82-2-573-7772 Fax +82-2-573-7710 December 20, 2013 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 In re : Sena Technologies, Inc. FCC Application for FCC ID: S7A-SP12 To Whom It May Concern: We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Regards, SeungHyun, Kim / Associate Research Engineer Sena Technologies, Inc.

FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 1 of 3 Upper Lower FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 2 of 3 Front Rear FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 3 of 3 ANTENNA- M/N: SENA_009

FCC ID: S7A-SP12 IC : 8154A-SP12 Copyright Ⓒ 2013, LTA Co., Ltd. SAMPLE LABEL & LOCATION Model : EXPAND FCC ID : S7A-SP12 IC : 8154A-SP12 CE : CE1177 KC : MSIP – CRM – SNA – SP12 Maid in Korea Sena Technologies

FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 1 of 2 Main Board – Front Main Board – Rear FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 2 of 2 RF Module Total internal Battery Speaker

Ref. No.: LR500111312K Copyright ○ c 2013, LTA Co., Ltd. Page 1 of 42 243 Jubug-Ri,Yangji-Myeon, Yongin-Si, Gyeonggi-Do, Korea 449-822 Tel: +82-31-323-6008 Fax: +82-31-323-6010 http://www.ltalab.com Dates of Tests: December 06 ~ December 13, 2013 Test Report S/N: LR500111312K Test Site : LTA CO., LTD. CERTIFICATION OF COMPLIANCE FCC ID IC APPLICANT Equipment Class : Part 15 Spread Spectrum Transmitter (DSS) Manufacturing Description : BLUETOOTH STEREO MOTORCYCLE HEADSET Manufacturer : Sena Technologies, Inc. Model name : EXPAND Test Device Serial No.: : Identical prototype Rule Part(s) : FCC Part 15.247 Subpart C; ANSI C-63.4-2009 Frequency Range : 2402 ~ 2480MHz RF power : Max 5.66 dBm – Conducted Data of issue : December 19, 2013 This test report is issued under the authority of: The test was supervised by: Jae-Ho Lee, Manager Young-Jin Lee, Test Engineer This test result only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the test laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. NVLAP LAB Code.: 200723-0 S7A-SP12 8154A-SP12 Sena Technologies, Inc. Ref. No.: LR500111312K Copyright ○ c 2013, LTA Co., Ltd. Page 2 of 42 TABLE OF CONTENTS 1. GENERAL INFORMATION ---------------------------------------------------------------------------- 2. INFORMATION ABOUT TEST ITEM --------------------------------------------------------------- 3. TEST REPORT --------------------------------------------------------------------------------------------- 3.1 SUMMARY OF TESTS ------------------------------------------------------------------------------ 3.2 FREQUENCY HOPPING SYSTEM REQUIREMENTS-------------------------------------------- 3.3 TECHNICAL CHARACTERISTICS TEST ------------------------------------------------------- 3.3.1 CARRIER FREQUENCY SEPARATION ---------------------------------------------------- 3.3.2 NUMBER OF HOPPING FREQUENCIES -------------------------------------------------- 3.3.3 20 dB BANDWIDTH ---------------------------------------------------------------------------- 3.3.4 TIME OF OCCUPANCY (Dwell Time) ------------------------------------------------------- 3.3.5 TRANSMITTER OUTPUT POWER ---------------------------------------------------------- 3.3.6 BAND EDGE ------------------------------------------------------------------------------------- 3.3.7 CONDUCTED SPURIOUS EMISSIONS ----------------------------------------------------- 3.3.8 RADIATED SPURIOUS EMISSIONS ------------------------------------------------------- 3.3.9 AC CONDUCTED EMISSIONS --------------------------------------------------------------- APPENDIX APPENDIX TEST EQUIPMENT USED FOR TESTS -------------------------------------------- 3 4 5 5 6 8 8 10 12 19 24 28 31 34 38 41 Ref. No.: LR500111312K Copyright ○ c 2013, LTA Co., Ltd. Page 3 of 42 1. General information 1-1 Test Performed Company name : LTA Co., Ltd. Address : 243, Jubug-ri,Yangji-Myeon,Youngin-Si, Kyunggi-Do, Korea. 449-822 Web site : http://www.ltalab.com E-mail : [email protected] Telephone : +82-31-323-6008 Facsimile : +82-31-323-6010 Quality control in the testing laboratory is implemented as per ISO/IEC 17025 which is the “General requirements for the competents of calibration and testing laboratory”. 1-2 Accredited agencies LTA Co., Ltd. is approved to perform EMC testing by the following agencies: Agency Country Accreditation No. Validity Reference NVLAP U.S.A 200723-0 2014-09-30 ECT accredited Lab. RRL KOREA KR0049 2015-03-06 EMC accredited Lab. FCC U.S.A 610755 2014-04-27 FCC filing FCC U.S.A 649054 2015-04-17 FCC CAB VCCI JAPAN R2133(10m), C2307 2014-06-21 VCCI registration VCCI JAPAN T-2009 2013-12-23 VCCI registration VCCI JAPAN G-563 2015-05-28 VCCI registration IC CANADA 5799A-1 2015-06-21 IC filing Ref. No.: LR500111312K Copyright ○ c 2013, LTA Co., Ltd. Page 4 of 42 2. Information about test item 2-1 Client & Manufacturer Company name : Sena Technologies, Inc. Address Telephone / Facsimile : : 210 Yangjae-dong Seocho-gu Seoul 137-130 Korea Tel : +82-2-573-7772 / Fax : +82-2-573-7710 2-2 Equipment Under Test (EUT) Trade name : SENA Model name : EXPAND Serial number : Identical prototype Date of receipt : December 03, 2013 EUT condition : Pre-production, not damaged Antenna type : Chip antenna (M/N:SENA_009) Max Gain 0.5 dBi Frequency Range : 2402 ~ 2480MHz RF output power : Max. 5.66 dBm - Conducted Number of channels : 79 Duty cycle : 80.69 % Channel spacing : 1MHz Channel Access Protocol : Frequency Hopping Spread Spectrum (FHSS) Type of Modulation : Basic Mode(GFSK), EDR Mode(Pi/4 DQPSK, 8DPSK) Power Source : DC 3.7V by battery Firmware Version : V1.0.0 2-3 Tested frequency Bluetooth LOW MID HIGH Frequency (MHz) 2402 2441 2480 2-4 Ancillary Equipment Equipment Model No. Serial No. Manufacturer Smart Phone SHV-E250S - Samsung- Ref. No.: LR500111312K Copyright ○ c 2013, LTA Co., Ltd. Page 5 of 42 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Limit Test Condition Status (note 1) 15.247(a) Carrier Frequency Separation > 25 kHz Conducted C 15.247(a) Number of Hopping Frequencies > 15 hops C 15.247(a) 20 dB Bandwidth 99% Bandwidth > 1.5 MHz C 15.247(a) Dwell Time < 0.4 seconds C 15.247(b) Transmitter Output Power < 250 mWatt C 15.247(d) Conducted Spurious emission > 20 dBc C 15.247(d) Band Edge > 20 dBc C 15.249 / 15.209 Field Strength of Harmonics < 54 dBuV (at 3m) Radiated C 15.109 Field Strength - C 15.207 /15.107 AC Conducted Emissions EN 55022 Line Conducted C 15.203 Antenna requirement - - C Note 1: C=Complies NC=Not Complies NT=Not Tested NA=Not Applicable Note 2: The data in this test report are traceable to the national or international standards. Note 1: Antenna Requirement à The Sena Technologies, Inc. , FCC ID: S7A-SP12 unit complies with the requirement of §15.203. The antenna type is chip antenna. Note 2: The sample was tested …

Text truncated - open the document above for the full version.

FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 1 of 4 Radiate Emission (9kHz ~ 30MHz) FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 2 of 4 Radiate Emission (30MHz ~ 1GHz) FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 3 of 4 Radiate Emission (Above 1GHz) FCC ID: S7A-SP12 IC: 8154A-SP12 Copyright ○ c 2013, LTA Co., Ltd. Page 4 of 4 Conducted Emission