S7A-SP26Bluetooth Stereo Motorcycle Headset

10S Motorcycle Bluetooth® Communication System © 1998-2015 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. 10S™, 10R™, 10U™, 10C™, Prism™, 20S™, Snowtalk™, 3S™, SMH10™, SMH5™, SMH5-FM™, SPH10™, SPH10H™, SPH10H-FM™, SMH10R™, SPH10S™, SPH10H™, SR10™, SR10i™, SM10™, EXPAND™, Bluetooth Pack for GoPro ® are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena. GoPro ® is a registered trademark of Woodman Labs of San Mateo, California. Sena Technologies, Inc. (“Sena”) is not affiliated with Woodman Labs. The Sena Bluetooth Pack for GoPro® is an after-market accessory specially designed and manufactured by Sena Technologies, Inc. for the GoPro® Hero3 and Hero4 allowing for Bluetooth capabilities. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod touch are registered trademarks of Apple Inc. Zumo™ is a trademark of Garmin Ltd. or its subsidiaries. TomTom™ is the trademark or registered trademark owned by TomTom International B.V. Other trademarks and tradenames are those of their respective owners. CONTENTS 1 INTRODUCTION 2 PACKAGE CONTENTS 3 INSTALLING THE 10S ON YOUR HELMET 3.1 Installing the Main Unit 3.1.1 Using the Clamp Unit 3.1.2 Using the Glued Surface Mounting Adapter 3.2 Installing the Speakers 3.3 Installing the Microphones 3.3.1 Using the Wired Boom Microphone 3.3.2 Using the Wired Microphone 4 GETTING STARTED 4.1 Button Operation 4.2 Powering On and Off 4.3 Charging 4.4 Low Battery Warning 4.5 Checking the Battery Level 4.5.1 LED Indicator 4.5.2 Voice Prompt Indicator 4.5 Volume Adjustment 4.6 Sena Softwares 4.6.1 Sena Device Manager 4.6.2 Sena Smartphone App 5 PAIRING THE 10S WITH BLUETOOTH DEVICES 5.1 Mobile Phone Pairing - Mobile Phone, Bluetooth Stereo Device 5.2 Second Mobile Phone Pairing - Second Mobile Phone, GPS, and SR10 5.3 Advanced Selective Pairing: A2DP Stereo or Handsfree 5.3.1 A2DP Stereo Music Only 5.3.2 HFP for Phone Call Only 5.4 Intercom Pairing 5.4.1 Pairing with Other 10S Headsets for Intercom Conversation 5.4.2 Pairing with Other Sena Headset Models for Intercom Conversation 6 MOBILE PHONE, GPS, SR10 6.1 Mobile Phone Call Making and Answering 6.2 Speed Dialing 6.3 GPS Navigation 6.4 Sena SR10, Two-Way Radio Adapter 7 STEREO MUSIC 7.1 By Bluetooth Wireless Stereo 7.2 By Stereo Audio Cable 7.3 Music Sharing 8 INTERCOM 8.1 Two-way Intercom 8.1.1 Starting Two-way Intercom 8.1.2 Ending Two-way Intercom 8.2 Three-way Intercom 8.2.1 Starting Three-way Intercom 8.2.2 Ending Three-way Intercom 8.3 Four-way Intercom 8.3.1 Starting Four-way Intercom 8.3.2 Ending Four-way Intercom 9 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT 10 GROUP INTERCOM 11 UNIVERSAL INTERCOM 11.1 Universal Intercom Pairing 11.2 Two-way Universal Intercom 11.3 Three-way Universal Intercom 11.4 Four-way Universal Intercom 11.4.1 Four-way Universal Intercom Case 1 11.4.2 Four-way Universal Intercom Case 2 12 FM RADIO 12.1 FM Radio On/Off 12.2 Preset Stations 12.3 Seek and Save 12.4 Scan and Save 12.5 Temporary Preset 12.6 Region Selection 13 FUNCTION PRIORITY 14 CONFIGURATION SETTING 14.1 Assigning Speed Dial 14.2 Enabling/Disabling Audio Boost 14.3 Enabling/Disabling Voice Activated Phone Answering 14.4 Enabling/Disabling Voice Activated Intercom 14.5 Enabling/Disabling HD Intercom 14.6 Enabling/Disabling Voice Prompts 14.7 Enabling/Disabling RDS AF 14.8 Enabling/Disabling Sidetone 14.9 Enabling/Disabling Advanced Noise Control™ 14.10 Delete All Bluetooth Pairing Information 14.11 Remote Control Pairing 14.12 Exit Voice Configuration Menu 15 REMOTE CONTROL 15.1 Pairing with the Handlebar Remote 15.2 Using the Handlebar Remote 16 FIRMWARE UPGRADE 17 TROUBLESHOOTING 17.1 Intercom Failure 17.2 Intercom Reconnection 17.3 Fault Reset 17.4 Factory Reset 18 OPERATION QUICK REFERENCE CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement FCC RF Exposure Statement FCC Caution CE Declaration of Conformity Industry Canada Statement Bluetooth License WEEE (Waste Electrical and Electronic Equipment) SAFETY INFORMATION Product Storage and Management Product Use Battery PRODUCT WARRANTY AND DISCLAIMER Limited Warranty Warranty Exclusions Reasons for Limited Liabilities Limitation of Liability Liabilities Disclaimer Warranty Service Free-of-charge Service Charged Service Return for Full Refund 1 INTRODUCTION Thank you for choosing the Sena 10S, Motorcycle Bluetooth Communication System. With the 10S, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations wirelessly, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The 10S is compliant with the Bluetooth 4.1 supporting the following profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio Distribution Profile (A2DP), and Audio Video Remote Control Profile (AVRCP). Please check with the manufacturers of other device to determine their compatibility with this headset. Please read this User’s Guide carefully before using the headset. Also check www.sena.com for the latest version of the User’s Guide and additional information related to Sena Bluetooth products. The 10S features: ● Bluetooth 4.1 ● Multi-way intercom up to 4 connections ● Bluetooth intercom up to 1.6 kilometers (1.0 miles)* ● Smartphone App for iPhone and Android ● Universal Intercom™ ● Music Sharing ● Intuitive voice prompts ● Advanced Noise Control™ ● Easy operation by versatile Jog Dial ● Can be used while charging on road trips ● Water resistant for use in inclement weather ● Built-in FM radio tuner with a station scan and save function ● Optional Handlebar Remote support (not included)…

Text truncated - open the document above for the full version.

SENA TECHNOLOGIES.Inc Dec 10 th , 2015 Applicant: SENA TECHNOLOGIES.Inc FCC ID: S7A-SP26 1. The typical placement of the EUT is on a motorcycle helmet. See the photo on next page. The distance between the device and user in the worst case application, is 30mm and more. 2. This product will not be available to be used data communication via PC, will be used charging function only. Seunghyun Kim Reasearch Engineer Inside Helmet

Sena Technologies,Inc. 19, Heolleung-ro 569-gil, Gangnam-gu, Seoul, Korea Date: Dec. 03, 2015 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA Letter of Authorization We, the undersigned, hereby authorize Harvey Sung of DT&C Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: S7A-SP26 including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of DT&C Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Sena Technologies,Inc. “I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a).” Sincerely, Seunghyun KIM Reasearch Engineer

Sena Technologies,Inc. 19, Heolleung-ro 569-gil, Gangnam-gu, Seoul, Korea Date: Dec. 03, 2015 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA RE: Request of Confidentiality for FCCID: S7A-SP26 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Sena Technologies,Inc. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Sena Technologies,Inc. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Schematics 3 Operational Description & Tune up procedure 4 Part Lists SHORT-TERM 5 External Photos 6 Internal Photos 7 Test-Setup Photos 8 User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Seunghyun KIM Reasearch Engineer

Sena Technologies,Inc. 19, Heolleung-ro 569-gil, Gangnam-gu, Seoul, Korea Date: Dec 02, 2015 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA DECLARATION FOR ADDITIONAL FREQUENCY HOPPING REQUIREMENTS To whom it may concern: We hereby declare that the device of S7A-SP26 meet following FCC requirements of the Section 15.247(a)(1) : 1. The hopping sequence is pseudorandom. 2. All channels are used equally on average. 3. The receiver input bandwidth approximately equal the transmit bandwidth. 4. The receiver hop in sequence with the transmit signal. Sincerely, Seunghyun Kim Reasearch Engineer

FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Page 1 / 3 View 1 FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Page 2 / 3 View 2 FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Page 3 / 3 View 3

FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. View 1 FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. View 2 FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. View 3 FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. View 4 <Antenna> FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. View 5 <Module>

MHzmm = Typical Power: ± =[ / ]*[√ ] = Thus SAR for this device is not required. [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW 30 Step 2-1) SAR test exclusion thresholds for 100MHz to 1500MHz at test separationn distances > 50 mm = N/A 0.37 ≤ 3, for 1g SAR Copyright Ⓒ 2015, DT&C Co., Ltd. Step 2-2) SAR test exclusion thresholds for 1500MHz to 6GHz at test separationn distances > 50 mm = N/A 2480 - Min. test separation distance = mW 7.76 7.90 dBm - Min. transmitting frequency = dB 5.90 dBm 2.00 dBm Measured Average Power: S7A-SP26 7.00 2.48 30 - Max. power with turn-up tolerance = 7 Used Step 1) SAR test exclusion thresholds for 100MHz to 6GHz at te st separationn distances ≤ 50 mm = [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] FCC ID : Standalone SAR test exclusion considerations December 8, 2015

FCC ID: S7A-SP26 IC: 8154A-SP26 Report No.: DRTFCC1512-0249 TRF-RF-238(01)150922 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 2 / 41 Test Report Version Test Report No. Date Description DRTFCC1512-0249 Dec. 08, 2015 Initial issue FCC ID: S7A-SP26 IC: 8154A-SP26 Report No.: DRTFCC1512-0249 TRF-RF-238(01)150922 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 3 / 41 Table of Contents 1. General Information .................................................................................... 4 1.1 Testing Laboratory ........................................................................................................... 4 1.2 Details of Applicant .......................................................................................................... 4 1.3 Description of EUT ........................................................................................................... 5 1.4 Declaration by the applicant / manufacturer ................................................................. 5 1.5 Test Conditions ................................................................................................................ 5 1.6 Test Equipment List ......................................................................................................... 6 1.7 Summary of Test Results ................................................................................................ 7 2. Test Methodology ........................................................................................ 8 2.1 EUT Configuration ............................................................................................................ 8 2.2 EUT Exercise ..................................................................................................................... 8 2.3 General Test Procedures ................................................................................................. 8 2.4 Description of Test Modes ............................................................................................... 8 2.5 Instrument Calibration ..................................................................................................... 8 3. Test Result ................................................................................................... 9 3.1 Maximum Peak Conducted Output Power ..................................................................... 9 3.1.1 Test Setup ..................................................................................................................... 9 3.1.2 Test Procedures ........................................................................................................... 9 3.1.3 Test Results .................................................................................................................. 9 3.2 6 dB Bandwidth Measurement ...................................................................................... 12 3.2.1 Test Setup ................................................................................................................... 12 3.2.2 Test Procedures ......................................................................................................... 12 3.2.3 Test Results ................................................................................................................ 12 3.3 Maximum Power Spectral Density. ............................................................................... 15 3.3.1 Test Setup ................................................................................................................... 15 3.3.2 Test Procedures ......................................................................................................... 15 3.3.3 Test Results ................................................................................................................ 15 3.4 Unwanted Emissions (Conducted) ............................................................................... 18 3.4.1 Test Setup ................................................................................................................... 18 3.4.2 Test Procedures ......................................................................................................... 18 3.4.3 Test Results ................................................................................................................ 19 3.5 Unwanted Emissions (Radiated) ................................................................................... 27 3.5.1 Test Setup ................................................................................................................... 28 3.5.2 Test Procedures ......................................................................................................... 28 3.5.3 Test Results ................................................................................................................ 29 3.6 Power line Conducted Emissions ................................................................................. 30 3.6.1 Test Setup ................................................................................................................... 30 3.6.2 Test Procedures ......................................................................................................... 30 3.6.3 Test Results ................................................................................................................ 31 3.7 Occupied Bandwidth ...................................................................................................... 33 3.7.1 Test Setup ................................................................................................................... 33 3.7.2 Test Procedures ......................................................................................................... 33 3.7.3 Test Results .......................................................................................................…

Text truncated - open the document above for the full version.

FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Test Setup photographs EUT Position: X-axis EUT Position: Y-axis EUT Position: Z-axis FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Test Setup Photo of Radiated Measurement (0.009 ~ 30MHz) FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Test Setup Photo of Radiated Measurement (below 1000MHz) FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Test Setup Photo of Radiated Measurement (Above 1GHz) FCCID: S7A-SP26 IC : 8154A-SP26 Copyright Ⓒ 2015, DT&C Co., Ltd. Test Setup Photo for AC Conducted Emissions