S7APARANIESD110Bluetooth Module

1 Parani-ESD100/110/200/210 User Guide Version 1.0.0 2006-07-19 FCC CONCERNS FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. (3)This transmitter module is authorized only for use in device(s) where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labelled in a visible area with the following: “Contains TX FCC ID: S7APARANIESD110”. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment 2 User Guide for the Parani-ESD100/110/200/210 Version 1.0.0 Firmware version 1.0.X Last revised on June 14, 2006 Printed in Korea Copyright Copyright 2002, Sena Technologies, Inc. All rights reserved. Sena Technologies reserves the right to make changes and improvements to its product without providing notice. Trademark Parani™ is a trademark of Sena Technologies, Inc. Windows® is a registered trademark of Microsoft Corporation. Ethernet® is a registered trademark of XEROX Corporation. Notice to Users When a system failure may cause serious consequences, protecting life and property against such consequences with a backup system or safety device is essential. The user agrees that protection against consequences resulting from system failure is the user's responsibility. This device is not approved for life-support or medical systems. Changes or modifications to this device not explicitly approved by Sena Technologies will void the user's authority to operate this device. Precautions and Safety Electricity Use only the supplied AC adapter. Use of unauthorized power adapter is not recommended. Electrical shock may result. Do not kink or crease the power cable or place heavy objects on the power cable. Fire can result from damaged power cables. Do not handle power plug and adapter with wet hands. Electrical shock may result. Immediately power off the product and unplug the AC adapter if smoke or odors emit from the product and adapter. Fire can result from improper use. Immediately power off the product and unplug the AC adapter if water or other liquids are present. Fire can result from improper use. Product Parani-ESD meets the RS-232 standards. Do not wire with non-standard products. Damage to your products may result from improper use. Do not drop or subject the device to impact. Damage to your products may result from improper use. Keep away from harsh environments including humid, dusty, and smoky areas. Damage to your products may result from improper use. Do not use excessive force on the buttons or attempt to disassemble the device. Damage to your products may result from improper use. Do not place heavy objects on the product. Damage to your products may result from improper use. Technical Support Sena Technologies, Inc. 210 Yangjae-dong, Seocho-gu Seoul 137-130, Korea Tel: (+82-2) 573-5422 Fax: (+82-2) 573-7710 E-Mail: [email protected] Website: http://www.sena.com 3 Contents 1. Introduction 6 1.1. Overview ................................................................................................................................... 6 1.2. Package Check List.................................................................................................................... 6 1.3. Product Specification.................................................................................................................. 7 2. Getting Started 8 2.1. Panel Layout .............................................................................................................................. 8 2.2. Connecting the Hardware .......................................................................................................... 8 2.2.1. Connecting Parani-ESD to Jig Board .............................................................................. 9 2.2.2. Connecting Power to Jig Board ....................................................................................... 9 2.2.3. Connecting a Device to Jig Board ................................................................................. 10 3. Configuration 11 3.1. Operation Modes...................................................................................................................... 11 3.2. Serial Ports ..............................................................................…

Text truncated - open the document above for the full version.

Sena Technologies, Inc. 210 Yangjae-dong Seocho-gu Seoul 137-130 Korea Tel. +82-2-571-8283 Fax +82-2-573-7710 FCC ID : S7APARANIESD110 Request for transmitter Modul e approval Transmitter Module Characteristics No Requirements EUT 1 Have its own RF shielding Device is equipped with metal shielding to cover RF section. Refer to external photos. 2 Have buffered modulation/data inputs (if such inputs are provided) All inputs to the modules are buffered th ought logic or microprocessor inputs. 3 Have it own power supply regulati on Internal 1.8V power regulation. 4 Meet the antenna requirements of Section 15.203 Device is equipped with unique antenna connector. Refer to external photos. 5 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing Device was tested on a supplied development platform for modular approval. Refer to setup photos. 6 Be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the out side of the device into which the module is installed must also display a label referring to the enclosed module Label is to be placed in front of the EUT(ESD 110), and other label is to be placed in the User’s Guide. Refer to FCC ID label format. 7 The modular transmitter is manufactured so t hat the user cannot influence the operation of the transmitter that will operate outsi de of the scope of the regulations. Refer to “User’s Guide” 8 Address compliance with the Commission’s RF exposure limits in Sections 1.1310 and 2.1091. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4). MPE was calculated.

Bluetooth modul e Parani-ESD110 RF Connector MMCX TX / RX Bluetooth Moldule Class1 (BEM001) UART TXD / RXD UART DTR / DSR DC3.3V Interface Connector 2.4GHz Helical Antenna RF Cable

Sena Technologies, Inc. 210 Yangjae-dong Seocho-gu Seoul 137-130, Korea Date: May 17, 2006 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Section 0.457(d)(2)(i) and 0.459 pertaining to confidential material. We, Sena Technologies Inc., would like the following documents regarding this submission for FCC ID: S7APARANIESD110 to be kept confidential. 1. Schematics 2. Parts List 3. Operation Description The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Young-sam Kim /Vice President /Sena Technologies Inc.

Report File No. : STROR-06-060 Date of Issue : 2006-08-02 Page : 50 of 51 FCC ID : S7APARANIESD110 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr 13. Attachment B – Photos of the EUT Front View of EUT Rear View of EUT

FCC ID LABEL 1. FCC ID label drawing 2. FCC ID label location SENA Technologies, Inc. Model : Parani-ESD110 FCC ID : S7APARANIESD110 Made in Korea This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)This devices may not cause harmful interference, and (2)This device must accept any interference received including interference that may cause undesired operation

Report File No. : STROR-06-060 Date of Issue : 2006-08-02 Page : 51 of 51 FCC ID : S7APARANIESD110 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Inner View of EUT(removal Shield cap)

Report File No. : STROR-06-060 Date of Issue : 2006-08-02 Page : 48 of 51 FCC ID : S7APARANIESD110 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr 12. Attachment A-1 Photo of the test set up Report File No. : STROR-06-060 Date of Issue : 2006-08-02 Page : 49 of 51 FCC ID : S7APARANIESD110 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Attachment A-2 Photos of the test set up