S7APROMISD205OABluetooth RS232C Serial Adaptor

USER MANUAL Version 2.0.2 (2006.06.07) Promi SD™ 205-OA Bluetooth RS232C Serial Adaptor by Bluetooth Enabling Wireless Serial Communications FCC CONCERNS FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device and its antenna must not be co-located or operating in conjunctio n with any other antenna or transmitter. Do not Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. Promi SD205-OA User Manual – Table of Contents 1 z Promi SD205-OA Bluetooth Serial Adapter SD205-OA Part Number Promi SD205-OA Description External type wireless serial adapter with dip switch Bluetooth Power Class Class1 Frequency range 2402 MHz~2480 MHz Number of channel 79ch Modulation Method GFSK Communication Method Half Duplex RF Range Up to 100m Operating Power range DC5V / 2A (AC100~240V / 50~60Hz) Operating Temperature range -20 ~ +55°C Operating Humidity range 95% Power Connector DC plug or 6 pin Serial connector Male DB9 Serial Interface RS-232 Serial Data Rate 1,200 ~ 230,400 bps Dip switch Yes (4 slots) Profile Serial Port Profile Applicable Antenna Helical Antenna, Dipole Antenna, Patch Antenna Dimensions (H ̄W ̄D) 62.5x31.2x16.3 Includes Helical Antenna, DC power cable Promi SD205-OA User Manual – Table of Contents 2 Table of Contents 1. Getting Started Components --------------------------------------------------------4 Assembly ------------------------------------------------------------- 4 Locating the Controls ------------------------------------------ 5 2. Configurations Operation Modes ------------------------------------------------- 7 LED Indicators -----------------------------------------------------8 Serial Ports ---------------------------------------------------------- 8 Reset to Factory Defaults ------------------------------------- 8 Terminal Program ------------------------------------------------ 9 Dip Switch ------------------------------------------------------------- 10 Pairing Button ----------------------------------------------------------10 3. Connections RS232 Interface --------------------------------------------------- 13 Pin Assignment ---------------------------------------------------- 14 Power Supply ------------------------------------------------------15 4. Specifications Bluetooth ----------------------------------------------------------- 17 Serial Interface --------------------------------------------------- 17 Power ---------------------------------------------------------------- 17 Mechanical Dimensions ---------------------------------------- 17 Environmental --------------------------------------------------- 17 Default Antenna -------------------------------------------------18 Wireless Coverage ---------------------------------------------- 18 Appendix A. AT Commands Terminology ------------------------------------------------------- A-2 Command Description --------------------------------------- A-3 Promi SD205-OA User Manual – 1. Getting Started 3 1. Getting Started z Components z Assembly z Locating the Controls Promi SD205-OA User Manual – 1. Getting Started 4 Components Assembly Promi SD205-OA Helical Antenna DC 5V Power Cable Fig.1-1 Components of SD205-OA Antenna is left-hand threaded. Fig.1-2 Assembly of SD205-OA Use of non-authorized power adapter is not recommended. Promi SD205-OA User Manual – 1. Getting Started 5 Locating the Controls Fig.1-3 Locating the Controls Front Panel Power Jack Back Label Power Switch Reset Button Pairing Button Promi SD205-OA User Manual – 2. Configurations 6 2. Configurations z Operation Modes z LED Indicators z Serial Ports z Reset to Factory Defaults z Terminal Program z Dip Switch z Pairing Button Promi SD205-OA User Manual – 2. Configurations 7 Operation Modes In addition to the serial port configurations such as bit/second, data bit, parity, stop bit, flow control, Promi SD205-OA has some configurations for Bluetooth. For getting the most out of Promi SD205-OA, user should understand the following Bluetooth connection schemes. A Bluetooth device can play a role as a master or slave. Master tries to connect itself to other Bluetooth device, and slave is waiting to be connected from other Bluetooth devices. A Bluetooth connection is always made by a pair of master and slave. A slave can be in two modes, Inquiry Scan or Page Scan mode. Inquiry Scan mode is waiting the packet of inquiry from other Bluetooth devices and Page Scan mode is waiting the packet of connection from other Bluetoo…

Text truncated - open the document above for the full version.

5.0V~12.0V 5.0V~12.0V Power ON/OFF Switch Bluetooth Serial Adapt o r (for Omron) Promi-SD205-OA DIP Switch Baud rate Set 2.4GHz Helical Antenna RS232 Tansceiver Serial Port DSUB-9P-Male TX / RX 3.3V LED Display BT_MODE BT_RESET Bluetooth Moldule Class1 (BEM001) LDO Vin = 5.0~12V Vout = 3.3V DC JACK DC5.0 V

Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 48 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr 12. Attachment B – Photos of the EUT Front View of EUT Rear View of EUT Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 49 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Left View of EUT Right View of EUT

FCC ID LABEL 1. FCC ID label drawing 2. FCC ID label location SENA Technologies, Inc. Model : Promi SD205-OA FCC ID : S7APROMISD205OA Made in Korea This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)This devices may not cause harmful interference, and (2)This device must accept any interference received including interference that may cause undesired operation

Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 50 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Inner of EUT Top View of Main-board Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 51 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Bottom View of Main-board (Not removal Bluetooth module) Left of Main-board Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 52 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Right of Main-board Front of Main-board Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 53 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Rear of Main-board

Report File No. : STROS-06-020 Date of Issue : 2006-06-15 Page : 1 / 51 TEST REPORT Equipment Under Test : Bluetooth Serial Adaptor Model No. : Promi SD205-OA Applicant : SENA Technologies, Inc. Address of Applicant : 210, Yangiae-dong, Seocho-gu, Seoul 137-130, Korea FCC ID S7APROMISD205OA Date of Receipt : 2006-05-20 Date of Test(s) : 2006-06-14 Date of Issue : 2006-06-15 Standards: FCC OET Bulletin 65 supplement C, ANSI/IEEE C95.1, C95.3 In the configuration tested, the EUT complied with the standards specified above. Remarks: Tested by : Elvin Lee 2006-06-15 Approved by : Albert Lim 2006-06-15 This report details the results of the testing carried out on one sample, the results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS Testing Korea Co., Ltd. or testing done by SGS Testing Korea Co., Ltd. in connection with distribution or use of the product described in this report must be approved by SGS Testing Korea Co., Ltd. in writing. Report File No. : STROS-06-020 Date of Issue : 2006-06-15 Page : 2 / 51 Contents 1. General Information 1.1 Testing Laboratory........................................................................................... 3 1.2 Details of Applicant.......................................................................................... 3 1.3 Version of Report............................................................................................. 3 1.4 Description of EUT(s)....................................................................................... 3 1.5 Test Environment............................................................................................. 4 1.6 Operation description........................................................................................ 4 1.7 Evaluation procedures....................................................................................... 4 1.8 The SAR Measurement System............................................................................ 5 1.9 System Components.......................................................................................... 7 1.10 SAR System Verification.................................................................................... 8 1.11 Tissue Simulant Fluid for the Frequency Band.......................................................... 10 1.12 Test Standards and Limits.................................................................................. 11 2. Instruments List.................................................................................... 13 3. Summary of Results................................................................................ 14 APPENDIX A. DASY4 SAR Report B. Uncertainty Analysis C. Photographs of EUT & EUT’s Test Setup D. Calibration certificate Report File No. : STROS-06-020 Date of Issue : 2006-06-15 Page : 3 / 51 1. General Information 1.1 Testing Laboratory SGS Testing Korea Co., Ltd. Wireless Div. 2FL, 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea 435-040 Telephone : +82 +31 428 5700 FAX : +82 +31 427 2371 Homepage : www.sgstesting.co.kr 1.2 Details of Applicant Applicant : SENA Technogies, Inc. Address 210, Yangiae-dong, Seocho-gu, Seoul 137-130, Korea Contact Person : Young-Sam Kim Phone No. : 82-31-573-7772 Fax No. : 82-31-573-7710 1.3 Version of Report Version Number Date 00 2006-06-15 1.4 Description of EUT(s) EUT Type Bluetooth Serial Adaptor Model Promi SD205-OA Serial Number - Hardware Version V1.0 Software Version V1.0 Mode of Operation Continuous RF Maximum RF Conducted Power 12.65 dBm(FHSS) Tx Frequency Range 2402 ~ 2480 MHz Rx Frequency Range 2402 ~ 2480 MHz Traffic Channel 1 ch/40 ch/79 ch Antenna Type / Gain Helical Antenna / 2 dBi Power Supply Type DC 5 V AC adapter Report File No. : STROS-06-020 Date of Issue : 2006-06-15 Page : 4 / 51 1.5 Test Environment Ambient temperature : 22.1 ° C Tissue Simulating Liquid : 22.1 ° C Relative Humidity : 54 % 1.6 Operation Configuration The device was controlled by using the test program in the notebook PC. The device was communicated with notebook PC. Measurements were performed on the lowest, middle and highest channels of the operating band. The EUT was set to maximum power level during all tests. Power supply used for the DC 5 V AC adapter. The DASY4 system measures power drift during SAR testing by comparing e-field in the same location at the beginning and at the end of measurement. 1.7 EVALUATION PROCEDURES - Power Reference Measurement Procedures The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The Minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. The minimum distance of probe sensors to surface is 4 mm. This distance cannot be smaller than the Distance of sensor calibration points to probe tip as defined in the probe properties (for example, 2.7 mm for an ET3DV6 probe type). - The entire evaluation of the spatial peak values is performed within the Post-processing engine (SEMCAD). The system always gives the maximum values for the 1 g and 10 g cubes. The algorithm to find the cube with highest averaged SAR is divided into the following stages: 1. The extraction of the measured data (grid and values) from the Zoom Scan. 2. The calculation of the SAR value at every measurement point based on all stored data (A/D values and measurement parameters) 3. The generation of a high-resolution mesh within the measured volume 4. The interpolation of all measured values from the measurement gr…

Text truncated - open the document above for the full version.

Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 1 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr TEST REPORT FCC RULES Part 15 Subpart C Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Kind of Product : Bluetooth Serial Adaptor Model Name : Promi SD205-OA FCC ID : S7APROMISD205OA Manufacturer : SENA Technologies, Inc. Serial No. : - Test Result : Complied This report details the results of the testing carried out on one sample, the results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS Testing Korea Co., Ltd. or testing done by SGS Testing Korea Co., Ltd. in connection with distribution or use of the product described in this report must be approved by SGS Testing Korea Co., Ltd. in writing. Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 2 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr VERIFICATION OF COMPLIANCE Applicant : SENA Technologies, Inc. Kind of Product : Bluetooth Serial Adaptor Brand Name : - Model Name : Promi SD205-OA Model Difference : - Report File No. : STROR-06-048 Date of test : May 10, 2006 ~ June 01, 2006 Receiver EUT : - APPLICABLE STANDARDS STANDARD TEST RESULT Part 15, Subpart B and Subpart C §15.247 Complied The above equipment was tested by SGS Testing Korea Co., Ltd. for compliance with the requirements set forth in the FCC RULES Part 15, Subpart B and Subpart C §15.247. The results of testing in this report apply to the product system that was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Te s t e d B y : Date June 05, 2006 Feel Jeong Approved By Date June 05, 2006 Albert Lim Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 3 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr INDEX CONTENTS Page 1. GENERAL INFORMATION 4 2. CONDUCTED POWERLINE TEST 6 3. SPURIOUS EMISSION, BAND EDGE, AND RESTRICTED BAND TEST 12 4. 20 dB BANDWIDTH MEASUREMENT 24 5. MAXIMUM PEAK OUTPUT POWER MEASURMENT 27 6. FREQUENCY SEPARATION 30 7. NUMBER OF HOPPING FREQUENCY 32 8. TIME OF OCCUPANCY (DWELL TIME) 34 9. POWER SPECTRAL DENSITY MEASURMENT 42 10. ANTENNA REQUIREMENT 45 11. Attachment A – Photos of the Test Set up 46 12. Attachment B – Photos of the EUT 48 Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 4 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr 1. GENERAL INFORMATION 1.1 General Description of EUT & Power Kind of Product Bluetooth Serial Adaptor Model Name Promi SD205-OA Power Supply DC 5 V AC adapter(100 ~240 Vac) Frequency Range 2402~2480 MHz(FHSS) Transmit Power 12.65 dBm (FHSS) Modulation Technique FHSS Number of Channels 79 CH (FHSS) Test Modulation Continuous RF Operating Conditions -20 °C ~ + 70 °C Antenna Type Helical Antenna(left-handed SMA Type) Antenna Gain 2 dBi Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 5 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr 1.2 Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD:FCC 47 C.F.R. Part15, Subpart B and Subpart C Standard Section Test Item Result 15.107 15.207 AC Power Conducted Emission PASS 15.247(a)(1) 20 dB Bandwidth PASS 15.247(b)(1) Maximum Peak Output Power PASS 15.205(a) 15.209(a) 15.247(d) Spurious Emission, Band Edge, and Restricted Bands PASS 15.247(a)(1) Frequency Separation PASS 15.247(a)(1)(iii) Number of Hopping Frequency PASS 15.247(a)(1)(iii) Time of Occupancy (Dwell Time) PASS 15.247(e) Power Spectral Density PASS Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 6 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-…

Text truncated - open the document above for the full version.

Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 46 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr 11. Attachment A-1 Photos of the test set up Report File No. : STROR-06-048 Date of Issue : 2006-06-05 Page : 47 of 53 FCC ID : S7APROMISD205OA The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.sgstesting.co.kr Attachment A-2 Photos of the test set up