S7GICB103BUBLUETOOTH CLOCK RADIO

Plug the included AC/DC power adapter into the DC POWER INPUT on the dock and an AC power outlet to power the dock. USB CHARGER LINE IN DC IN 5V FM ANT USER’S GUIDE V: 842-01 ICB103 Bluetooth Speaker with Clock Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. • The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet. • Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely. La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur. • Battery shall not be exposed to excessive heat such as sunshine, fire or the like. Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable. • Caution marking is located at the rear or bottom of the apparatus. Attention marquage est situé sur le paneau arrière ou inférieur de l’unité. • The marking information is located at the rear or bottom of apparatus. Le marquage est situé sur le paneau arrière ou inférieur de l’unité. 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. • CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. • WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. • AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité. • CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. • WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • WARNING: Do not place this unit directly onto furniture surfaces with any type of soft, porous, or sensitive finish. As with any rubber compound made with oils, the feet could cause marks or staining where the feet reside. We recommend using a protective barrier such as a cloth or a piece of glass between the unit and the surface to reduce the risk of damage and/or staining. • WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. • WARNING: Shock hazard - Do Not Open. • AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely. La prise du secteur est u…

Text truncated - open the document above for the full version.

DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Date: August 27, 2013 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: S7GICB103BU Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics SCH.pdf Block Diagram BlockDiagram.pdf Operational Description CircuitDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Xia Wu Lane, WangLian Hamlet,WangNiuDun Town,DongGuan,GuangDong,China ............................................................... Signature Hu Guozhi /General Manager ............................................................... Typed name and Title

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: August 27, 2013 SUBJECT: FCC Application for (FCC ID: S7GICB103BU ) To Whom It May Concern: I, the undersigned, hereby attest to the fact that I will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1. Devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. 3. Pt 2.1077 contains the list of information that must be included in the Declaration of Conformity, which must be supplied with each product sold. The DoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(c)(2), the responsible party is either the Manufacturer or if the product is imported the Importer . Regards, Signature: Hu Guozhi/ General manage: Applicant: DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Address: Xia Wu Lane, WangLian Hamlet, WangNiuDun Town, DongGuan City, GuangDong Province, China

DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Model Differences Statement Product name: Bluetooth Clock Radio Product No.: ICB103BU, ICB103P, ICB103B Describe the differences: The circuit principle, PCB wiring and intenal structure of the above three models are the same, Only the model name and the appearance of color are different. Signature: Hu Guozhi /General Manager Data: 2013-08-27

DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY FCC ID: S7GICB103BU POWER OF ATTORNEY Date: August 27,2013 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on August 26,2014. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Signature: Hu Guozhi /General Manager .................................................................................... [typed name and title] DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Xia Wu Lane, WangLian Hamlet,WangNiuDun Town,DongGuan,GuangDong,China

Reference No.: WTD13S0604822E Page 67 of 74 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 19 Photographs - Constructional Details 19.1 EUT – External View Reference No.: WTD13S0604822E Page 68 of 74 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Reference No.: WTD13S0604822E Page 69 of 74 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Reference No.: WTD13S0604822E Page 70 of 74 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

FCC Label Location for model: ICB103BU, ICB103P, ICB103B The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Model No.: ICB103BU FCC ID: S7GICB103BU This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any nterference received, including interference that may cause undesired operation.

FCC Label Sample for model: ICB103BU,ICB103P,ICB103B FCC ID: S7GICB103BU This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Reference No.: WTD13S0604822E Page 71 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 19.2 EUT – Internal View RF Antenna RF MODULE Reference No.: WTD13S0604822E Page 72 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 19.3 EUT-RF Module View Reference No.: WTD13S0604822E Page 73 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn =End of test report==

Reference No.: WTD13S0604822E Page 1 of 73 FCC TEST REPORT Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn FCC ID : S7GICB103BU Applicant : DONG GUAN WANG NIU DUN WELLCOM ELECTRONICS FACTORY Address : Xia Wu Lane, WangLian Hamlet, WangNiuDun Town, DongGuan City, GuangDong Province, China Manufacturer : DONG GUAN WELLCOM ELECTRONICS COMPANY LIMITED Address : NANYU INDUSTRIAL PARK,NANCHANG ROAD,WANGNIUDUN TOWN,DONGGUAN CITY,CHINA Equipment Under Test (EUT) : Product Name : Bluetooth Clock Radio Model No. : ICB103BU, ICB103P, ICB103B Standards : FCC CFR47 Part 15 Section 15.247:2012 Date of Test : July 04~25, 2013 Date of Issue : Augsut 06, 2013 Test Result : PASS Remark: * The sample described above has been tested to be in compliance with the requirements of ANSI C63.4:2003. The test results have been reviewed and comply with the rules listed above and found to meet their essential requirements. The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Testing location: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel: +86-755-83551033 Fax: +86-755-83552400 Compiled by: Approved by: Maikou Zhang / Project Engineer Philo Zhong / Manager Reference No.: WTD13S0604822E Page 2 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 2 Test Summary Test Items Test Requirement Result Spurious Radiated Emissions 15.205(a) 15.209 15.247(d) PASS Band edge Emissions 15.247(d) PASS Spurious RF Conducted Emissions from out of band 15.247(d) PASS Duty Cycle 15.35 PASS Conducted Emissions 15.207 PASS 20dB Bandwidth 15.215c 15.247(a)(1) PASS Maximum Peak Output Power 15.247(b)(1) PASS Frequency Separation 15.247(a)(1) PASS Number of Hopping Frequency 15.247(a)(1)(iii) PASS Dwell time 15.247(a)(1)(iii) PASS Maximum Permissible Exposure (Exposure of Humans to RF Fields) 1.1307(b)(1) PASS Reference No.: WTD13S0604822E Page 3 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 3 Contents Page 1 COVER PAGE ................................................................................................................................................ 1 2 TEST SUMMARY..........................................................................................................................................................2 3 CONTENTS....................................................................................................................................................................3 4 GENERAL INFORMATION.........................................................................................................................................5 4.1 GENERAL DESCRIPTION OF E.U.T.....................................................................................................................5 4.2 DETAILS OF E.U.T..............................................................................................................................................5 4.3 DESCRIPTION OF SUPPORT UNITS.....................................................................................................................5 4.4 TEST FACILITY....................................................................................................................................................5 4.5 TEST LOCATION..................................................................................................................................................5 5 EQUIPMENT USED DURING TEST..........................................................................................................................6 5.1 EQUIPMENTS LIST...............................................................................................................................................6 5.2 MEASUREMENT UNCERTAINTY...........................................................................................................................6 5.3 TEST EQUIPMENT CALIBRATION.........................................................................................................................6 6 CONDUCTED EMISSION............................................................................................................................................7 6.1 E.U.T. OPERATION.............................................................................................................................................7 6.2 EUT SETUP........................................................................................................................................................7 6.3 CONDUCTED EMISSION TEST RESULT...............................................................................................................8 7 RADIATED EMISSIONS............................................................................................................................................10 7.1 EUT OPERATION :............................................................................................................................................10 7.2 TEST SETUP......................................................................................................................................................11 7.3 SPECTRUM ANALYZER SETUP..........................................................................................................................12 7.4 TEST PROCEDURE............................................................................................................................................13 7.5 CORRECTED AMPLITUDE & MARGIN CALCULATION..............................…

Text truncated - open the document above for the full version.

Reference No.: WTD13S0604822E Page 65 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 18 Photographs – Test Setup 18.1 Conducted Emissions 18.2 Radiated Emissions Below 30MHz Reference No.: WTD13S0604822E Page 66 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Above 1GHz