S8B-SK-15SK-15

Slide the BACtrack Skyn over the fingers and palm of your non-dominant hand. Place the device approximately 1 inch below your wrist joint, making sure that the white sensor circle is facing the underside of your wrist (ie. the opposite position of a normal watch). Tighten the strap. Make sure it is tight, but not uncomfortable. 1. 2. 3. On the top of the BACtrack Skyn, press and hold the power button for two seconds. The button will turn blue and remain on for about a minute, indicating the device is ON. Powering ON/OFF the BACtrack Skyn Wearing the BACtrack Skyn Charging the BACtrack Skyn BACtrack Skyn Operator Manual Make sure the BACtrack Skyn is powered OFF by pressing and holding the power button for two seconds. Attach the charging cable to the bottom of the device by lining up the two magnetic squares on the cable and device. Insert the USB connector into a USB port to begin charging. When the BACtrack Skyn is connected to the charger the light will begin pulsing green. 1. 2. 3. To turn the device off, press and hold the power button for two seconds. The button will fade from blue to gray, indicating the device is OFF. It takes approximately 3 hours to fully charge, at which point the light will stop pulsing and remain green, indicating the device is fully charged. The BACtrack Skyn should not be worn while it is being charged. The BACtrack Skyn can still be ON when the button is not blue. To check if the device is still ON , firmly tap the top of BACtrack SKYN. If the button pulses blue, the device is still ON and recording data. If the button remains gray, the device is OFF. Connecting to the BACtrack Skyn App Enable Bluetooth on your Apple iOS device. Download and install the BACtrack Skyn App from the Apple iTunes App Store. Open the BACtrack Skyn App and power your device ON. The App will automatically connect to your Skyn and you will see a confirmation message that you've successfully connected your device. 1. 2. 3. 4. Additional product information, instructions and troubleshooting can be found in the App. Item# SK-15 FCC ID: S8B-SK-15 IC: 10935A-SK15 This device (will) comply with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment (will be) tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by KHN Solutions Inc may void the user’s authority to operate the equipment. RF EXPOSURE WARNING STATEMENT This equipment (will) comply with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guide. RSS-GEN, ISSUE 4, NOVEMBER 2014 This device complies with ISEDC license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Radiation Exposure Statement: This equipment complies with the IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. Cet appareil est conforme à Industrie Canada une licence standard RSS exonérée. Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer d’interférences. 2. Cet appareil doit accepter toute interférence reçue,y compris les interférences pouvant provoquer un fonctionnement indésirable de l’appareil. Énoncé d’exposition aux rayonnements : Cet équipement est conforme aux limites d’expositions aux rayonnements ioniques RSS-102 pour un environnement incontrôlé. Regulatory Compliance To access product regulatory information, please visit https://skyn.bactrack.com/regulatory

KHN SOLUTIONS, Inc. KHN Solutions, Inc. | 300 Broadway, Suite 26, San Francisco, CA 94133 | 877.334.6876 [email protected] | www.BACtrack.com May 21, 2021 Reference: Application for BACtrack Skyn, Item SK-15 FCC ID: S8B-Sk-15 We are requesting approval of the above item for original certification under FCC Rule part 15.247. BACtrack Skyn is a wearable device which includes a sensor designed to detect the presence of alcohol in the skin. It uses a Bluetooth Low Energy radio (2.402 to 2.480 GHz), operating at 0dBm transmit power. The radio’s model number is nRF52832 (Nordic Semiconductors). Thank you for your assistance. Sincerely, Pauline Basaran Pauline Basaran Vice President Operations 415.964.5130

BACtrack� KHN SOLUTIONS, Inc. ------ ----- ----- - MayJ0,2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia. Mary land 21 046 Re: Request for confidentiality FCC ID: S8B-SK-15 To w hom it may concern, We hereby respectfully request that under the provision of 47 CFR 0.459 and 0.457(d) the docwnents listed below and attached with this application for certification be provided with confidential status. •Schematics.pdf •Operational Oescription.pdf • Frequency Block Diagrams.pdf As well as short-term confidential treatment ( 180 days) of information accompanying this application as outlined below: • Internal Photos • User's Manual • External Photos • Test Set-up Photos Any exhibit/ information for which we have requested confidentiality, but which may not be accorded such treabnent by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, �� Pauline Basaran Vice President Operations KHN Solution,, Inc I 300 Bro,1dw.iy, Suite 26, San fr,111c1SlO. lA 9•1133 I 877 33•1 C,8/G 1nfo(itlBACtrack.co111 I www.BACtr.Kk.co111

BACtrack Skyn - SK-15 Electronic Labeling Per Section 4 Access and Instructions to display regulatoryinformation - Electronic Labeling Guidance Overview: The BACtrack Skyn does not have a built-in physicalintegrated display. The BACtrack Skyn works with an iOS device that hasa display. The iOS device is required to utilize the required BACtrack Skyn app. 4.1 User Steps to Access Information Starting from the Home Menu: Step 1 - Access the Device Info screen by tappingthe Skyn icon in the upper right corner of the screen.See red arrow. 4.2 The BACtrack Skyn works with an iOS device that hasa display. The iOS device is required to utilize the required BACtrack Skyn app. 4.3 The FCC ID is clearly readable on the above screenshot. 4.4 The regulatory information is secured in a factoryset unalterable format. 4.5 A physical label applied to outside of the retailbox. See below for label information. Dimensions: 210 mm x 90 mm See below for position of label on outside of theretail box. Sample of Temporary Label for for purchasing and Importation Dimensions: 50 mm x 25mm Label will be placed on outside of shipping packaging.

2.4GHz Mini Antenna, SMTP/N 2450AT18A100 Detail Specification: Page 1 of 5 *Efficiency based on Johanson's standard evaluation board ±± ±± ±± www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 3.0 2018 Johanson Technology, Inc. All Rights Reserved "High Frequency Ceramic Solutions" Part Number 7/9/2018 Avg. Rad Efficiency* Let us help you with the antenna design, optimization, and tuning! 2450AT18A100 2400 - 2500 76% General Specifications Frequency (MHz) 18 months max. -40 to +125°C -40 to +125°C 3000 Return Loss (dB) Impedance Input Power Storage Period Storage Temperature Operating Temperature Reel Quantity 50 Ω 2 Watts max. (CW) Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. e.g. 2450AT18A100(E or S)100% Tin Packing Style Evaluation Board 2450AT18A100-EBSMA (see page 2&3 for details) Bulk (loose) T & R Suffix = E or S Suffix = E P/N Suffix Mechanical Dimensions In L 0.1260.0083.200.2 W 0.0630.0081.600.2 T 0.0511.30+.004/-.008 +0.1/-0.2 a 0.0200.0120.500.3 Terminal Configuration Function FEED NC No. 1 2 mm e.g. 2450AT18A100E e.g. 2450AT18A100SSuffix = S Part Number Explanation Peak Gain (dBi typ.) Average Gain (dBi typ.) 0.5 -0.5 9.5 min. ① ② L W a T Want the layout file? Request it at: www.johansontechnology.com/ask-a-question 2.4GHz Mini Antenna, SMTP/N 2450AT18A100 Detail Specification: Page 2 of 5 JTI P/N for Matching Circuit: Cap (1.0pF): 500R07S1R0BV4T Inductor (2.7nH): L-07C2N7SV6T Inductor (3.9nH): L-07C3N9SV6T www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 3.0 2018 Johanson Technology, Inc. All Rights Reserved "High Frequency Ceramic Solutions" 7/9/2018 Mounting Considerations 1: Evaluation Board Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. GND NO GND Units in mm ) ) 13.5mm 6.5mm 39.5mm 6.5mm 50Ω Feed Line Antenna 4mm ) Matching Component JTI P/Ns: L-14C2N7JV4 L-14C2N2JV4 * 2.6 4.2 1.6 1.9 0.4 2.7nH 1.0pF 3.9nH To order a pre-tuned 50Ω EVB with a female SMA connector click here: www.johansontechnology.com/request-a-sample Reference p/n: 2450AT18A100-EBSMA 2.4GHz Mini Antenna, SMTP/N 2450AT18A100 Detail Specification: Page 3 of 5 Return Loss with matching circuit @ +25CVSWR with matching circuit @ +25C and +125C www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 3.0 2018 Johanson Technology, Inc. All Rights Reserved "High Frequency Ceramic Solutions" 7/9/2018 Mounting Considerations 1: Typical Electrical Performance (T=25°C) Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. 2.4GHz Mini Antenna, SMT P/N 2450AT18A100 Detail Specification: Page 4 of 5 www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 3.0 2018 Johanson Technology, Inc. All Rights Reserved "High Frequency Ceramic Solutions" 7/9/2018 Mounting Considerations 1: Antenna Performance Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Z X (0°) Y X (0°) Typical 2D radiation patterns @ 2.44GHz YZ-plane XZ-plane XY-plane Z (0°) Y XY cut @2.45GHz Vertical Horizontal XZ cut @2.45GHz Vertical Horizontal YZ cut @2.45GHz Vertical Horizontal 2.4GHz Mini Antenna, SMTP/N 2450AT18A100 Detail Specification: Page 5 of 5 www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 3.0 2018 Johanson Technology, Inc. All Rights Reserved Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Soldering Information RoHS Compliance Packaging information For layout review contact our Applications Team at: "High Frequency Ceramic Solutions" Antenna tuning, optimization, and validation services: For more antennas and to download measured S-parameters, go to: MSL Info 7/9/2018 www.johansontechnology.com/ipc-antenna-services www.johansontechnology.com/antennas www.johansontechnology.com/ipcsoldering-profile www.johansontechnology.com/msl-rating www.johansontechnology.com/tape-reel-packaging www.johansontechnology.com/ask-a -question www.johansontechnology.com/rohs-compliance Need help designing the antenna in? Use our antenna design services! www.johansontechnology.com/ipc-antenna-services We provide 2 free layout reviews and if you need us to tune and characterize the antenna on your product (inside anechoic chamber) we can do that too. Small lab fee may apply for the latter.

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. EAR-Controlled Data - This document contains technical data whose export and reexport/retransfer is subject to control by the U.S. Department of Commerce under the Export Administration Act and the Export Administration Regulations. The Department of Commerce’s prior written approval may be required for the export or re- export/retransfer of such technical data to any foreign person, foreign entity or foreign organization whether in the United States or abroad. More: https://www.bis.doc.gov/index.php/forms-documents/regulations-docs/14-commerce-country-chart/fileT BACtrack BACtrack Skyn Wearable Alcohol Monitor FCC 2.1093:2021 Bluetooth Low Energy Report: BACT0001.3 CERTIFICATE OF EVALUATION 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing Last Date of Evaluation: Friday, July 16, 2021 BACtrack EUT: BACtrack Skyn Wearable Alcohol Monitor RF Exposure Evaluation Standards Specification Method FCC 2.1093:2021 FCC 447498 D01 General RF Exposure Guidance v06 Results Method Clause Description Applied Results Comments 4.3.1 SAR Test Exclusion Yes Pass None Deviations From Evaluation Standards None Approved By: Donald Facteau, Process Architect Report No. BACT0001.3EAR-Controlled Data2/10 RF Exposure Condition 2018-07-17 The following RF Exposure conditions were used for the assessment documented in this report: Intended Use Portable Location on Body (if applicable) Head/Torso How is the Device Used Wristband Radios Contained in the Same Host Device BTLE Simultaneous Transmitting Radios None Body Worn Accessories None Environment General Population/Uncontrolled Exposure Report No. BACT0001.3EAR-Controlled Data3/10 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. BACT0001.3EAR-Controlled Data4/10 ACCREDITATIONS AND AUTHORIZATIONS 2021.02.26 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Recognized as an EU Notified Body validated for the EMCD and RED Directives. United Kingdom BEIS – Recognized by the UK as an Approved Body under the UK Radio Equipment and UK EMC Regulations. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. BACT0001.3EAR-Controlled Data5/10 FACILITIES 2020.12.15 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-11 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. BACT0001.3EAR-Controlled Data6/10 PRODUCT DESCRIPTION 2018-07-17 Client and Equipment Under Evaluation Information Company Name: BACtrack Address: 300 Broadway, Suite 26 City, State, Zip: San Francisco, 94133 Evaluation Requested By: Pauline Basaran EUT: BACtrack Skyn Wearable Alcohol Monitor Date of Evaluation: Friday, July 16, 2021 Information Provided by the Party Requesting the Evaluation Functional Descr…

Text truncated - open the document above for the full version.

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. BACtrack BACtrack Skyn Wearable Alcohol Monitor FCC 15.247:2021 Bluetooth Report: BACT0001, Issue Date: July 6, 2021 NVLAP LAB CODE: 200630-0 CERTIFICATE OF TEST 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing. Last Date of Test: May 19, 2021 BACtrack EUT: BACtrack Skyn Wearable Alcohol Monitor Radio Equipment Testing Standards Specification Method FCC 15.247:2021 ANSI C63.10:2013, KDB 558074 Results Method Clause Test Description Applied Results Comments 6.2 Powerline Conducted Emissions Yes Pass 11.6 Duty Cycle Yes Pass 11.8.2 Occupied Bandwidth Yes Pass 11.9.1.1 Output Power Yes Pass 11.9.1.1 Equivalent Isotropic Radiated Power Yes Pass 11.10.2 Power Spectral Density Yes Pass 11.11 Band Edge Compliance Yes Pass 11.11 Spurious Conducted Emissions Yes Pass 11.12.1, 11.13.2, 6.5, 6.6 Spurious Radiated Emissions Yes Pass Deviations From Test Standards None Approved By: Kyle Holgate, Operations Manager Report No. BACT00012/57 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. BACT00013/57 ACCREDITATIONS AND AUTHORIZATIONS 2021.02.26 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Recognized as an EU Notified Body validated for the EMCD and RED Directives. United Kingdom BEIS – Recognized by the UK as an Approved Body under the UK Radio Equipment and UK EMC Regulations. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. BACT00014/57 FACILITIES 2020.12.15 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-11 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. BACT00015/57 MEASUREMENT UNCERTAINTY TMU.2015.07.10 Measurement Uncertainty When a measurement is made, the result will be different from the true or theoretically correct value. The difference is the result of tolerances in the measurement system that cannot be completely eliminated. To the extent that technology allows us, it has been our aim to minimize this error. Measurement uncertainty is a statistical expression of measurement error qualified by a probability distribution. A measurement uncertainty estimation has been performed for each test per our internal quality document QM205.4.6. The estimation is used to compare the measured result with its "true" or theoretically correct value. The expanded measurement uncertainty (K=2) can be found in the table below. A lab specific value may also be found in the applicable test description section. Our measurement data meets or exceeds the measurement uncertainty requirements of the applicable specification; therefore, the test data can be compared directly to the specification limit to determine compliance. The calculations for estimating measurement uncertainty are based upon ETS…

Text truncated - open the document above for the full version.

POWERLINE CONDUCTED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.03.25.0 PSA-ESCI 2021.03.17.0 POWERLINE CONDUCTED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.03.25.0 PSA-ESCI 2021.03.17.0 XMit 2020.12.30.0 BACT0001_TX-BenchTest (2).JPG BACT0001_TX-BenchTest (4).JPG DIRECT CONNECT Report No. BACT00012/8 XMit 2020.12.30.0 BACT0001_TX-BenchTest (8).JPG DIRECT CONNECT Report No. BACT00013/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. BACT00014/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. BACT00015/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. BACT00016/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. BACT00017/8