S8F826XWireless Remote Controller Handheld

Installation Data Installation Man ual AquaLink ® RS PDA - Pool Digital Assistant WARNING FOR YOUR SAFETY - This product must be installed and serviced by a pro fessional pool/spa service technician. The procedures in this manual must be followed ex actly. Failure to follow warning notices and instructions may result in property damage, serious injury, or death. Pool/Spa Combination Systems and Pool Only/Spa Only Systems (Models PS4, PS6, PS8, P4, and P8) H 0 5 7 2 2 0 0 - ATTENTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an electrical source on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help Modi cations made to this equipment, which are not authorized by the manufacturer, may void the user’s authority to operate this equipment. Page 3 Table of Contents Section 1. Important Safety Instructions........... 4 Section 2. System Overview............................. 6 2.1 Package Contents............................. 6 2.2 System Component Speci cations and Dimensions................................ 7 2.3 Basic Plumbing................................ 8 Section 3. Installation........................................ 10 3.1 Power Center Mounting................... 10 3.2 High Voltage Wiring........................ 10 3.3 Low Voltage Wiring......................... 14 3.4 Heater Connection........................... 15 3.5 Temperature Sensors........................ 18 3.6 Jandy Valve Actuators...................... 18 3.7 PDA Transceiver J-box Installation. 18 Section 4. System Startup.................................. 20 4.1 Handheld Remote Programming...... 20 4.2. Restarting the System (Clear Memory) Menu..................... 23 4.3 PDA System Defaults and General Modes................................. 23 4.4 PDA Handheld Remote Menu Flow Chart....................................... 25 Section 5. Troubleshooting................................ 26 5.1 PDA Quick Troubleshooting Guide. 26 Section 6. Power Center Wiring Diagram......... 28 Section 7. Power Center PCB DIP Switch Settings............................................. 29 7.1 DIP Switch Functions...................... 29 7.2 DIP Switch Settings for Pool and Spa Combination.............................. 30 7.3 DIP Switch Settings for Pool or Spa Only........................................... 31 Section 8. General, Water Feature and Light Aux Labels.............................. 32 DATE OF INSTALLATION INSTALLER INFORMATION INITIAL PRESSURE GAUGE READING (WITH CLEAN FILTER) PUMP MODELHORSEPOWER FILTER MODELSERIAL NUMBER PDA MODEL SERIAL NUMBER NOTES: EQUIPMENT INFORMATION RECORD Page 4 Section 1. Important Safety Instructions READ AND FOLLOW ALL INSTRUCTIONS Lire la notice technique. All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: WARNING Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6° F. The symptoms of hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include: 1) unawareness of impending danger; 2) failure to perceive heat; 3) failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal damage in pregnant women; 6) unconsciousness resulting in a danger of drowning. DANGER To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot tub if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the equipment assembly. WARNING To Reduce the Risk of Injury - a)The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes. b) Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C). c) Before entering a spa or hot tub, the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature-regulating devices varies. d) The use of alcohol, drugs, or medication before or during spa or hot tub use may lead to unconsciousness with the possibility of drowning. e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulato…

Text truncated - open the document above for the full version.

Operation Data Owner's Man ual AquaLink ® RS PDA - Pool Digital Assistant H 0 5 7 2 3 0 0 - WARNING FOR YOUR SAFETY: This product must be installed and serviced by a pro fessional pool/spa service technician. The procedures in this manual must be followed ex actly. Failure to follow warning notices and instructions may result in property damage, serious injury, or death. ATTENTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an electrical source on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help Modi cations made to this equipment, which are not authorized by the manufacturer, may void the user’s authority to operate this equipment. Pool/Spa Combination Systems and Pool Only/Spa Only Systems (Models PS4, PS6, PS8, P4, and P8) Page 3 DATE OF INSTALLATION INSTALLER INFORMATION INITIAL PRESSURE GAUGE READING (WITH CLEAN FILTER) PUMP MODELHORSEPOWER FILTER MODELSERIAL NUMBER PDA HANDHELD REMOTE MODEL SERIAL NUMBER NOTES:                                                    EQUIPMENT INFORMATION RECORD Page 4  READ AND FOLLOW ALL INSTRUCTIONS Lire la notice technique.    WARNING Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6° F. The symptoms of hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include: 1) unawareness of impending danger; 2) failure to perceive heat; 3) failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal damage in pregnant women; 6) unconsciousness resulting in a danger of drowning. DANGER To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot tub if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the equipment assembly. WARNING To Reduce the Risk of Injury - a)The water in a spa should never exceed 104°F (40°C). Water temperatures b…

Text truncated - open the document above for the full version.

keypcb_V20.sch-1 - Mon Feb 21 18:15:05 2005

PDA_v2.0.sch-1 - Mon Feb 21 18:12:15 2005

PDA_v2.0.sch-2 - Mon Feb 21 18:12:53 2005

RF_V20.sch-1 - Tue Feb 22 17:02:34 2005

香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 1 of 17 No. : HM153648 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Applicant: Laars, Inc., dba Waterpik Technologies Pool Products & Heating Systems. 6000 Condor Drive, Moorpark, CA93021, USA Description of Samples: Model name: PDA pool/spa wireless remote controller handheld Model no.: 8265 Brand name: Jandy FCC ID: S8F826X Date Samples Received: 2005-03-22 Date Tested: 2005-04-13 Investigation Requested: FCC Part 15 Subpart C Conclusions: The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remarks: For additional models details, see page 5. K C Lee, EMD for Chief Executive 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 2 of 17 No. : HM153648 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). CONTENT: Cover Page 1 of 17 Content Page 2-3 of 17 1.0 General Details 1.1 Test Laboratory Page 4 of 17 1.2 Applicant Details Page 4 of 17 HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 17 Description of EUT operation 1.4 Date of Order Page 5 of 17 1.5 Submitted Sample Page 5 of 17 1.6 Test Duration Page 5 of 17 1.7 Country of Origin Page 5 of 17 1.8 Additional Information of EUT Page 6 of 17 2.0 Technical Details 2.1 Investigations Requested Page 7 of 17 2.2 Test Standards and Results Summary Page 7 of 17 3.0 Test Results 3.1 Radiated Emission Page 8-13 of 17 3.2 Conducted Emission Page 14 of 17 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 3 of 17 No. : HM153648 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Appendix A List of Measurement Equipment Page 15 of 17 Appendix B Photographs Page 16-17 of 17 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 4 of 17 No. : HM153648 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong 1.2 Applicant Details Laars, Inc., dba Waterpik Technologies Pool Products & Heating Systems. 6000 Condor Drive, Moorpark, CA93021, USA HKSTC Code Number for Applicant HKS001 Manufacturer Laars, Inc., dba Waterpik Technologies Pool Products & Heating Systems. 6000 Condor Drive, Moorpark, CA93021, USA 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 5 of 17 No. : HM153648 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.3 Equipment Under Test [EUT] Description of Sample Product: PDA pool/spa wireless remote controller handheld Manufacturer: Laars, Inc., dba Waterpik Technologies Pool Products & Heating Systems. Brand Name: Jandy Model Number: 8265 Input Voltage: 3Vd.c. (“AA” size battery x 2) Additional Product: Wireless SpaLink remote controller handheld Additional Model Number: 8266 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is a PDA pool/spa wireless remote controller handheld, the transmission signal is frequency hopping of channels frequency range 915.3 - 923.7MHz. 1.4 Date of Order 2005-03-22 1.5 Submitted Sample(s): 1 Sample per model 1.6 Test Duration 2005-04-13 1.7 Country of Origin China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 6 of 17 No. : HM153648 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-05-17 TEST REPORT Page 7 of 17 No. : HM153648 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf…

Text truncated - open the document above for the full version.

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP