S9E-GS200DWireless Slew Angle Sensor

Trimble Inc. 345 SW Avery Ave Corvallis, OR 97333 USA 541.752.9000 Applicant as U.S. Agent Letter of Attestation Date: 05-01-2024 To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: S9E-GS200D Trimble, Inc. (“the applicant”) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. Designated U.S. Agent from Applicant Company Company Name: Trimble, Inc Contact Person: Katherine Allen Address: 5475 Kellenburger Road, Building 2, Dayton, Ohio, 45424, United States Tel.: +1 818-600-1001 Email: [email protected] FCC FRN: 0013284146 Sincerely yours, Signature Printed Name: Katherine Allen Title: Worldwide Compliance Manager Email: [email protected]

Trimble Inc. 345 SW Avery Ave Corvallis, OR 97333 USA 541.752.9000 Attestation Statements Not Covered Entity Applicant To: Federal Communications Commission Date: 05-01-2024 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(ii) filing FCC ID: S9E-GS200D Trimble, Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely yours, Applicant Signature Printed Name: Katherine Allen Title: Worldwide Compliance Manager Address: 5475 Kellenburger Road, Building 2, Dayton, Ohio, 45424, United States Tel.: +1.818.600.1001 Email: [email protected]

Trimble Inc. 345 SW Avery Ave Corvallis, OR 97333 USA 541.752.9000 Attestation Statements Not Covered Equipment To: Federal Communications Commission Date: 05-01-2024 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) filing FCC ID: S9E-GS200D Trimble Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Katherine Allen Title: Worldwide Compliance Manager Address: 5475 Kellenburger Road, Building 2, Dayton, Ohio 45424, United States Tel.: +1.818.600.1001 Email: [email protected]

Confidentiality Letter Date: 05-01-2024 Subject: Confidentiality Request for IC: 5817A-GS000D FCC ID: S9E-GS200D Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term Permanent External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation /NII software security attestation Short Term Permanent Part List/Tune-Up Procedure Short Term Permanent Schematics Short Term Permanent Test Setup Photos Short Term Permanent User’s Manual Trimble, Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04- 1705. Sincerely, Katherine Allen//Worldwide Compliance Manager By: (Signature) (Print name//Title)

2.88 4.00 1.35 0.59 1.17 1.36 0.26 0.13 NOTES: Dimensional tolerance: ±15mils PMR FCC LABEL - GS032-FCC-V2 GS SERIES SLEW SENSOR UB304-GS032-FCC-V2 C 2:121 A 1INITIAL RELEASE- 09-SEP-2024 PMR FCC LABEL LOCATION GS SERIES SLEW SENSOR C 2:122 A

Prüfbericht – Produkte Test Report - Products Prüfbericht-Nr.: Test report no.: IN2418XY 001 Auftrags-Nr.: Order no.: 146785551 010 Seite 1 von 3 Page 1 of 3 Kunden-Referenz-Nr.: Client reference no.: 2269507 Auftragsdatum: Order date: 2023-04-26 Auftraggeber: Client: Trimble Inc. 5475 Kellenburger Road , Building 2,Dayton, Ohio 45424, United States Prüfgegenstand: Test item: Wireless Load Cell Sensor Bezeichnung Identification GS032-FCC-V2 Serien -Nr.: Serial no.: Engineering Sample Auftrags-Inhalt: Order content: Testing and issue of Test Report and Grant Certificate Prüfgrundlage: Test specification: FCC 1.1310, and RSS 102 Issue 5 KDB 447498 D01 Wareneingangsdatum: Date of sample receipt: 2023-10-18 Prüfmuster-Nr.: Test sample no: A003584412-022 A003584412-023 Prüfzeitraum: Testing period: 2023-10-19 - 2023-11-05 Ort der Prüfung: Place of testing: Wireless laboratory, Bangalore Prüflaboratorium: Testing laboratory: TÜV Rheinland (India) Pvt. Ltd. 27/B,2nd cross road, Electronic city Phase1, Banglore-560100, India FCC Test Site Registration No: 496599 IC Test Site Registration No: 3466E-1 Prüfergebnis*: Test result*: Pass geprüft von: tested by: genehmigt von: authorized by: Datum: Date: 2024-08-12 Ausstellatum: Issue date: 2024-08-12 Stellung / Position: Yogesh V Senior Engineer Stellung / Position: Madhu K N Asst. Manager Sonstiges / Other: FCC ID: S9E-GS200D IC: 5817A-GS000D Zustand des Prüfgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TÜV Rheinland (India) Pvt. Ltd, Plot No.27/B, 2nd Cross, Electronic city, Industrial Area, Phase I, Hosur Road Bangalore-560 100, India Mail: [email protected] ∙ Web: www.ind.tuv.com Produkte Products www.tuv.com Prüfbericht - Nr.: Test Report No.: IN2418XY 001 Seite 2 von 3 Page 2 of 3 1 Maximum Permissible Exposure 1.1 RF Exposure Compliance Requirement The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 1.2 RF Exposure Limits: 1.2.1 For FCC 1. According to FCC Part 1 Subpart I 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) showed in Table 1. F or ƒ = Frequency in MHz Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation. Produkte Products www.tuv.com Prüfbericht - Nr.: Test Report No.: IN2418XY 001 Seite 3 von 3 Page 3 of 3 Test Results: Antenna details: Sl.No RF Protocols Antenna Type Antenna Gain (dBi) 1 Sub-GHz Monopole 1.68 Radio Protocol Antenna Model Frequency (MHz) Maximum measured RF output power with tune- up Value (dBm) Max power Including tune-up tolerance * (mW) Antenna Gain in linear Min Separation distance (CM) Power Density (Pd)(mW/cm²) FCC Limit (mW/cm2) Sub-GHz Monopole 903 7.36 8.36 1.4723125 20 0.0020 0.602 1.2.2 For IC According to IC RSS 102 Issue 5: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radiofrequency (RF) radiation as specified in section 4 showed in Table 4. Radio Protocol Antenna Model Frequency (MHz) Maximum measured RF output power with tune- up Value (dBm) Max power Including tune-up tolerance * (mW) Antenna Gain in linear Min Separation distance (CM) Power Density (Pd)(mW/cm²) IC Limit (mW/cm2) Sub-GHz Monopole 903 7.36 8.36 1.4723125 20 0.0020 0.2792 1.3 Conclusion The Power density of the EUT is less than defined limit as shown above, Hence EUT is meeting MPE Calculation.

1 TA011 - Datasheet Specifications • Part Number: TA011 • Frequency: 868 MHz, 869 MHz, 902-928 MHz • Antenna Gain: Frequency (MHz) Antenna Gain (dB) 868 3.23 902 1.68 916 0.40 928 0.38 Table 1: Antenna Gain Figure 1: Antenna TA011 Note: TA011 antenna is not used in Wireless Radio Anemometer Sensor. Trimble Inc. 5475 Kellenburger Road , Building 2,Dayton, Ohio 45424, United States 2 Radiation Pattern • XY Plane - 868 MHz Figure 2: Antenna Radiation Pattern – 868 MHz • XY Plane - 902 MHz Figure 3: Antenna Radiation Pattern – 902 MHz 3 • XY Plane - 916 MHz Figure 4: Antenna Radiation Pattern – 916 MHz • XY Plane - 928 MHz Figure 5: Antenna Radiation Pattern – 928 MHz

Prüfbericht – Produkte Test Report - Products Prüfbericht-Nr.: Test report no.: IN2418XY 001 Auftrags-Nr.: Order no.: 146785551 010 Seite 1 von 48 Page 1 of 48 Kunden-Referenz-Nr.: Client reference no.: 2269507 Auftragsdatum: Order date: 2023-04-26 Auftraggeber: Client: Trimble Inc. 5475 Kellenburger Road , Building 2,Dayton, Ohio 45424, United States Prüfgegenstand: Test item: Wireless Slew Angle Sensor Bezeichnung Identification GS032-FCC-V2 Serien -Nr.: Serial no.: Engineering Sample Auftrags-Inhalt: Order content: Testing and issue of Test Report and Grant Certificate Prüfgrundlage: Test specification: FCC Part 15 Subpart C 15.247,15.205, 15.207 & 15.209 RSS 247 Issue 3, RSS Gen Issue 5 Wareneingangsdatum: Date of sample receipt: 2023-10-18 Prüfmuster-Nr.: Test sample no: A003584412-022 A003584412-023 Prüfzeitraum: Testing period: 2023-10-19 - 2023-11-05 Ort der Prüfung: Place of testing: Wireless laboratory, Bangalore Prüflaboratorium: Testing laboratory: TÜV Rheinland (India) Pvt. Ltd. 27/B,2nd cross road, Electronic city Phase1, Banglore-560100, India FCC Test Site Registration No: 496599 IC Test Site Registration No: 3466E-1 Prüfergebnis*: Test result*: Pass geprüft von: tested by: genehmigt von: authorized by: Datum: Date: 2024-08-12 Ausstellatum: Issue date: 2024-08-12 Stellung / Position: Yogesh V Senior Engineer Stellung / Position: Madhu K N Asst. Manager Sonstiges / Other: FCC ID: S9E-GS200D IC: 5817A-GS000D Zustand des Prüfgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TÜV Rheinland (India) Pvt. Ltd, Plot No.27/B, 2nd Cross, Electronic city, Industrial Area, Phase I, Hosur Road Bangalore-560 100, India Mail: [email protected] ∙ Web: www.ind.tuv.com Produkte Products www.tuv.com Prüfbericht - Nr.: Test Report No.: IN2418XY 001 Seite 2 von 48 Page 2 of 48 1 Alle eingesetzten Prüfmittel waren zum angegebenen Prüfzeitraum gemäß eines festgelegten Kalibrierungsprogramms unseres Prüfhauses kalibriert. Sie entsprechen den in den Prüfprogrammen hinterlegten Anforderungen. Die Rückverfolgbarkeit der eingesetzten Prüfmittel ist durch die Einhaltung der Regelungen unseres Managementsystems gegeben. Detaillierte Informationen bezüglich Prüfkonditionen, Prüfequipment und Messunsicherheiten sind im Prüflabor vorhanden und können auf Wunsch bereitgestellt werden. The equipment used during the specified testing period was calibrated according to our test laboratory calibration program. The equipment fulfils the requirements included in the relevant standards. The traceability of the test equipment used is ensured by compliance with the regulations of our management system. Detailed information regarding test conditions, equipment and measurement uncertainty is available in the test laboratory and could be provided on request. 2 Wie vertraglich vereinbart, wurde dieses Dokument nur digital unterzeichnet. Der TÜV Rheinland hat nicht überprüft, welche rechtlichen oder sonstigen diesbezüglichen Anforderungen für dieses Dokument gelten. Diese Überprüfung liegt in der Verantwortung des Benutzers dieses Dokuments. Auf Verlangen des Kunden kann der TÜV Rheinland die Gültigkeit der digitalen Signatur durch ein gesondertes Dokument bestätigen. Diese Anfrage ist an unseren Vertrieb zu richten. Eine Umweltgebühr für einen solchen zusätzlichen Service wird erhoben. As contractually agreed, this document has been signed digitally only. TUV Rheinland has not verified and unable to verify which legal or other pertaining requirements are applicable for this document. Such verification is within the responsibility of the user of this document. Upon request by its client, TUV Rheinland can confirm the validity of the digital signature by a separate document. Such request shall be addressed to our Sales department. An environmental fee for such additional service will be charged. 3 Prüfklausel mit der Note * wurden an qualifizierte Unterauftragnehmer vergeben und sind unter der jeweiligen Prüfklausel des Berichts beschrieben. Abweichungen von Prüfspezifikation(en) oder Kundenanforderungen sind in der jeweiligen Prüfklausel im Bericht aufgeführt. Test clauses with remark of * are subcontracted to qualified subcontractors and descripted under the respective test clause in the report. Deviations of testing specification(s) or customer requirements are listed in specific test clause in the report. 4 Die Entscheidungsregel für Konformitätserklärungen in diesem Prüfbericht basiert auf der "Null-Grenzwert- Regel" und der "Einfachen Akzeptanz" gemäß ILAC G8:2019 und IEC Guide 115:2021, es sei denn, in der auf Seite 1 dieses Berichts genannten angewandten Norm ist etwas anderes festgelegt oder vom Kunden gewünscht. Dies bedeutet, dass die Messunsicherheit nicht berücksichtigt wird und daher auch nicht im Prüfbericht angegeben wird. The decision rule for statements of conformity in this test report is based on the “Zero Guard Band Rule” and “Simple Acceptance” in accordance with ILAC G8:2019 and IEC Guide 115:2021, unless otherwise specified in the applied standard mentioned on Page 1 of this report or r…

Text truncated - open the document above for the full version.