SE506HAC2115FM transmitter

Federal Communication Commission Interference Statement This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Notice: (1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord by used. (2) Use only shielded cables to connect I/O devices to this equipment. (3) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Neutron Engineering Inc. B1, No. 37, Lane 365, Yang-Kuang St., Nei-Hu Dis., Taipei, Taiwan, R.O.C. Applicant: IN WIN DEVELOPMENT INC. FCC ID: SE506HAC2115 Request for Confidentiality Dear Sir/Madam, We are the agent of IN WIN DEVELOPMENT INC. and represent them to apply for FCC ID: SE506HAC2115. In this case, the IN WIN DEVELOPMENT INC. would like to request for confidentiality for some portions of the data contained in this application pursuant to 47 CFR 0.459 of the Commission Rules. As the following: 1. Schematics 2. Block Diagrams 3. Operational description Thank you very much. Sincerely, Andy Chiu Neutron Engineering Inc.

Project No.: 0605048 Page 2 of 5 Neutron Engineering Inc. 0605048 060504 8

Report No.: NEI-FCCP-1-0605048 Page 20 of 20 Neutron Engineering Inc. 6. PRODUCT LABELING -- FCC ID label -- The remained portion of label statement required by FCC is attached in the user’s manual. -- Location of Label on EUT -- 0.4 cm 3.2 cm

Project No.: 0605048 Page 3 of 5 Neutron Engineering Inc. 0605048 060504 8 Project No.: 0605048 Page 4 of 5 Neutron Engineering Inc. 0605048 060504 8 Project No.: 0605048 Page 5 of 5 Neutron Engineering Inc. 0605048 060504 8

Report No.: NEI-FCCP-1-0605048 Page 2 of 20 Neutron Engineering Inc. Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: NEI-FCCP-1-0605048 Page 3 of 20 Neutron Engineering Inc. Table of Contents Page 1 . CERTIFICATION 4 2 . SUMMARY OF TEST RESULTS 5 2.1 TEST FACILITY 6 2.2 MEASUREMENT UNCERTAINTY 6 3 . GENERAL INFORMATION 7 3.1 GENERAL DESCRIPTION OF EUT 7 3.2 DESCRIPTION OF TEST MODES 8 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9 3.4 DESCRIPTION OF SUPPORT UNITS 10 4 . EMC EMISSION TEST 11 4.1 RADIATED EMISSION MEASUREMENT 11 4.1.1 RADIATED EMISSION LIMITS 11 4.1.2 MEASUREMENT INSTRUMENTS LIST 12 4.1.3 TEST PROCEDURE 12 4.1.4 DEVIATION FROM TEST STANDARD 12 4.1.5 TEST SETUP 13 4.1.6 EUT OPERATING CONDITIONS 13 4.1.7 TEST RESULTS 14 5 . EUT TEST PHOTO 19 6 . PRODUCT LABELING 20 Report No.: NEI-FCCP-1-0605048 Page 4 of 20 Neutron Engineering Inc. 1. CERTIFICATION E q u i p m e n t : FM transmitter Trade Name : digidock M o d e l N o . : AC-211X(X=0~9) A p p l i c a n t : IN WIN DEVELOPMENT INC. Data of Test : May 11, 2006 ~ Jun. 01, 2006 Te s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C / RSS-210: 2004/ ANCI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-0605048) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and CNLA according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: NEI-FCCP-1-0605048 Page 5 of 20 Neutron Engineering Inc. 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: (Antenna to EUT distance is 3 m) FCC Part15, Subpart C Standard Test Item Judgment 15.207 Conducted Emission N/A Note(2) 15.209 15.239(c) Radiated Emission PASS 15.239(a) Occupied Bandwidth PASS 15.239(b) Radiated Output Power PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2)The EUT’s power source from battery. Report No.: NEI-FCCP-1-0605048 Page 6 of 20 Neutron Engineering Inc. 2.1 TEST FACILITY The test facilities used to collect the test data in this report is OS02 at the location of No.132-1, Lane 329, Sec. 2, Palain Road, Shijr City, Taipei, Taiwan. 2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE C01 ANSI150 KHz ~ 30MHz 1.94 B. Radiated Measurement : Test Site Method Measurement Frequency Range Ant. H / V U，(dB) NOTE OS-01 ANSI30MHz ~ 200MHz V 3.82 30MHz ~ 200MHz H 3.60 200MHz ~ 1,000MHz V 3.86 200MHz ~ 1,000MHz H 3.94 OS-02 ANSI30MHz ~ 200MHz V 2.48 30MHz ~ 200MHz H 2.16 200MHz ~ 1,000MHz V 2.50 200MHz ~ 1,000MHz H 2.66 Report No.: NEI-FCCP-1-0605048 Page 7 of 20 Neutron Engineering Inc. 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment FM transmitter Trade Name digidock Model No. AC-211X(X=0~9) OEM Brand/Model No. N/A Model Difference Model AC-211X, X may be 0 to 9. Model difference between each other only the changes in which not effective the EMI performance. Product Description The EUT is a FM transmitter. Key features: ＊ All-in-one FM Transmitter / Charger. ＊ Compatible with any audio device. ＊ Charge USB-Powered device. ＊ High Fidelity, full stereo sound. ＊ Safety fuse protects against power spikes. ＊ 6 channels selection for better audio quality. ＊ LED indicator for power status. ＊ No batteries needed. Specifications: ＊ FM Channel: 6 channels (88.5/ 88.7/ 88.9/ 107.5/ 107.7/ 107.9 MHz) ＊ Operation temp: 0°C~60°C ＊ Storage temp: -10°C~70°C ＊ Power input: DC+12V (car cigar lighter socket) ＊ USB output: +5V / 700mA (MAX) ＊ Dimension: 40*147*26mm ＊ Net Weight: 70g Power Supply Input: DC+12V (car cigar lighter socket) USB output: +5V / 700mA (MAX) Connecting I/O Port(s) Please refer to the User's Manual Products Covered N/A Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Report No.: NEI-FCCP-1-0605048 Page 8 of 20 Neutron Engineering Inc. 3.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following …

Text truncated - open the document above for the full version.

Report No.: NEI-FCCP-1-0605048 Page 19 of 20 Neutron Engineering Inc. 5. EUT TEST PHOTO Radiated Measurement Photos Radiated Emission Test Set-UP, Frequency Between 30 - 1000MHz