SI2315LT81Remote Control Transmitter

FCC ID: S I 23 15LT81 T H I S DEV I CE COM P L I ES W I T H P A RT 15 O F T H E F C C RUL E S . OPER A T ION IS SU B J EC T TO T H E FO LLOW I N G TW O CONDI T I ONS : (1) T H I S DEV I CE M A Y NO T CAU S E HARM F U L I N T E RF E R E N CRE AND (2) T H I S DEV I CE M U S T ACCE P T ANY I N T E RF E R E N C E RE CE IV E D , I N CL UDI N G I N T E R F E R E N CE T H AT M A Y CAUS E U N D ESIR E D O PER A T I O N . 1.75” 1” ENCLOSURE VIEWED FROM REAR Title FCC Certification Label For LT8-1 Transmitter Date : 09/16/04 Drawn By: DGL LANCO Electronics Inc. 915 W. Hawthorne Lane West Chicago, IL. 60185

Page 1 of 17 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE Engineering Test Report No. 34077-01 Measurement of RF Interference from a Model LT8-1 Transmitter For : Lanco, Inc. West Chicago, IL P.O. No. : 09130104 Date Received : September 14, 2004 Date Tested : September 14, 2004 Test Personnel : Richard E. King Specification : FCC "Code of Federal Regulations” Title 47 Part 15, Subpart C Test Report By : Richard E. King Witnessed by : David Lambert Lanco Inc. Approved By : Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 34077-01 THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 17 NO. 1.0 INTRODUCTION....................................................................................................................................3 1.1 Description of Test Item........................................................................................................................3 1.2 Purpose................................................................................................................................................3 1.3 Deviations, Additions and Exclusions......................................................................................................3 1.4 Applicable Documents...........................................................................................................................3 1.5 Subcontractor Identification....................................................................................................................3 1.6 Laboratory Conditions............................................................................................................................3 2.0 TEST ITEM SETUP AND OPERATION.................................................................................................3 2.1 Power Input..........................................................................................................................................4 2.2 Grounding.............................................................................................................................................4 2.3 Peripheral Equipment.............................................................................................................................4 2.4 Interconnect Cables...............................................................................................................................4 2.5 Operational Mode..................................................................................................................................4 2.6 Test Item Modifications.........................................................................................................................4 3.0 TEST EQUIPMENT.................................................................................................................................4 3.1 Test Equipment List...............................................................................................................................4 3.2 Calibration Traceability..........................................................................................................................4 3.3 Measurement Uncertainty......................................................................................................................4 4.0 REQUIREMENTS, PROCEDURES AND RESULTS...............................................................................5 4.1 Powerline Conducted Emissions.............................................................................................................5 4.1.1 Requirements.................................................................................................................................5 4.2 Duty Cycle Factor Measurements.........................................................................................................5 4.2.1 Procedures....................................................................................................................................5 4.2.2 Results..........................................................................................................................................6 4.3 Radiated Measurements........................................................................................................................6 4.3.1 Requirements.................................................................................................................................6 4.3.2 Procedures.....................................................................................................................................6 4.3.3 Results...........................................................................................................................................7 4.4 Occupied Bandwidth Measurements.......................................................................................................7 4.4.1 Requirement...................................................................................................................................7 4.4.2 Procedures.....................................................................................................................................7 4.4.3 Results...........................................................................................................................................8 5.0 CONCLUSIONS......................................................................................................................................8 6.0 CERTIFICATION....................................................................................................................................8 7.0 ENDORSEMENT DISCLAIMER........................................…

Text truncated - open the document above for the full version.