SI5WUB310AWireless 802.11g Portable USB Adapter

1 802.11b/g Wireless USB Adapter User's Guide Version 1.0 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device was tested for typical by stander conditions that may occur during use. To comply with FCC RF exposure requirements a minimum separation distance of 1.5cm must be maintained between the user’s body and the device, including the antenna. 3 CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. 4 Table of Contents Federal Communications Commission (FCC) Interference statement 2 CE Mark Warning 3 Chapter 1 - Getting Started 1.1 About Your 802.11b/g WLAN USB Adapter 5 1.2 Package Content 5 1.3 System Requirement 5 1.4 LED Definition 6 1.5 Adapter Hardware and Utility Installation 6 1.6 Using the Utility to Configure Your Network 14 Chapter 2 – Maintenance 2.1 The Version Screen 25 2.2 Uninstalling the Driver 25 2.3 Uninstall the Client Utility 25 2.3 Upgrading the Wireless Utility 25 5 Chapter 1 - Getting Started This chapter introduces the Adapter and prepares you to use the Wireless Utility. 1.1 About Your 802.11b/g WLAN USB Adapter The Adapter is an IEEE 802.11b, and 802.11g compliant wireless LAN adapter. With the Adapter, you can enjoy wireless mobility within almost any wireless networking environment. The following lists the main features of your Adapter. 9 Your Adapter can communicate with other IEEE 802.11b/g compliant wireless devices. 9 Automatic rate selection. 9 Standard data transmission rates up to 54 Mbps. 9 Offers 64-bit, 128-bit and 152-bit WEP (Wired Equivalent Privacy) data encryption for network security. 9 Supports IEEE802.1x and WPA (Wi-Fi Protected Access). 9 Low CPU utilization allowing more computer system resources for other programs. 9 A built-in antenna. 9 Driver support for Windows XP/2000. 1.2 Package Content ¾ 802.11b/g WLAN USB Adapter ¾ Installation and Manual CD ¾ Quick Start Guide ¾ Warranty/Registration Adapter 1.3 System Requirement z Pentium class notebook computers with at least one available USB slot z Microsoft Windows XP or 2K z CD-ROM drive 6 1.4 LED Definition The following table describes the LED on the 802.11b/g WLAN USB Adapter LED COLOR STATUS DESCRIPTION OFF The Adapter has no connection Blinking SlowlyThe Adapter is connected LINK Green Blinking The Adapter is sending or receiving data 1.5 Adapter Hardware and Utility Installation NOTE: If you have connected the USB Adapter to your computer, please remove it first. Follow the instructions below to install the USB Adapter and Utility. STEP 1 Insert the Driver and Utility CD into CD drive STEP 2 If your CD Autorun is enabled, the Main Installation Menu will show. (Otherwise open your CD folder and double-click on the “setup.exe” file) 7 STEP 3 Click the button of INSTALL. The InstallShield wizard prepares for installation. STEP 4 The InstallShield Wizard prompts you for confirmation. Click Next on the following menu. 8 STEP 5 Choose to install client utility and driver or install driver only. We recommend proceeding with “Install Client Utilities and Driver” STEP 6 A warning question will pop up, click “Yes” on it. STEP 7 In the destination Folder screen you are asked to confirm the Destination Folder for the application software. If you would like, you may change the destination folder to another location. Click Next 9 STEP 8 Select a program folder and click on Next. 10 STEP 9 The installation gives you information regarding the Client Utility to be used. Click Next on it. STEP 10 Choose the client utility. Click Next. 11 STEP 11 At this moment please insert your USB Adapter to your Laptop and click OK. STEP 12 You will get the “Found News Hardware Wizard” menu; click on Cancel. 12 STEP 13 At the hardware installation menu click Continue Anyway. (Our product has been tested under Windows XP and found to be fully compatible click Continue Anyway.) 13 STEP 14 The setup configuration shows the installation progress STEP 15 Click Finish to complete the client utility installation. Your c…

Text truncated - open the document above for the full version.

FCC ID Label Location (FCC ID: SI5WUB310A)

50 +0.00-0.25 18 +0. 0 0-0 . 25 WUB-310A_FCC Label Label Location : WUB-310A FCC ID: SI5WUB310A Wireless 802.11g Portable USB Adapter

Page 3 Page 4 Page 5

FCC ID: SI5WUB310A Report No.RF940317L18 Operational Description This device is a Wireless 802.11g Portable USB Adapter which operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by host equipment. The antenna used in this product is Printed antenna without connector. The other instruction, please have a look at the users manual.

D3: DAE SN: 510

APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION D1: SAM PHANTOM

A - 1 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA A1: TEST CONFIGURATION Tip of EUT Position The Bottom of the EUT to the flat phantom distance 9 mm A - 2 Bottom of EUT Position The Bottom of the EUT to the flat phantom distance 10 mm A - 3 EUT Photo A - 4 Liquid Level Photo MSL 2450MHz D=150mm A - 5 Date/Time: 2005/5/30 70:25:37 Test Laboratory: Advance Data Technology WUB-310A EVO N800C Horizontal Mode 1 11b DUT: Wireless 802.11g Portable USB Adapter ; Type: WUB-310A ; Test Frequency: 2412 MHz Communication System: 802.11b ; Frequency: 2412 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2412 MHz; σ = 1.98 mho/m; ε r = 54; ρ = 1000 kg/m 3 ; Liquid level : 150mm Phantom section: Flat Section ; Separation distance : 9 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Low Channel 1/Area Scan (5x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.267 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 11.4 V/m Peak SAR (extrapolated) = 0.527 W/kg SAR(1 g) = 0.275 mW/g; SAR(10 g) = 0.149 mW/g Maximum value of SAR (measured) = 0.295 mW/g A - 6 A - 7 Date/Time: 2005/5/30 07:41:07 Test Laboratory: Advance Data Technology WUB-310A EVO N800C Horizontal Mode 1 11b DUT: Wireless 802.11g Portable USB Adapter ; Type: WUB-310A ; Test Frequency: 2437 MHz Communication System: 802.11b ; Frequency: 2437 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2437 MHz; σ = 2.02 mho/m; ε r = 53.9; ρ = 1000 kg/m 3 ; Liquid level : 150mm Phantom section: Flat Section ; Separation distance : 9 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Mid Channel 6/Area Scan (5x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.270 mW/g Mid Channel 6/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 11.1 V/m Peak SAR (extrapolated) = 0.510 W/kg SAR(1 g) = 0.260 mW/g; SAR(10 g) = 0.139 mW/g Maximum value of SAR (measured) = 0.284 mW/g A - 8 Date/Time: 2005/5/30 08:11:13 Test Laboratory: Advance Data Technology WUB-310A EVO N800C Horizontal Mode 1 11b DUT: Wireless 802.11g Portable USB Adapter ; Type: WUB-310A ; Test Frequency: 2462 MHz Communication System: 802.11b ; Frequency: 2462 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2462 MHz; σ = 2.04 mho/m; ε r = 53.8; ρ = 1000 kg/m 3 ; Liquid level : 150mm Phantom section: Flat Section ; Separation distance : 9 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 High Channel 11/Area Scan (5x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.196 mW/g High Channel 11/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 9.88 V/m Peak SAR (extrapolated) = 0.384 W/kg SAR(1 g) = 0.196 mW/g; SAR(10 g) = 0.106 mW/g Maximum value of SAR (measured) = 0.210 mW/g High Channel 11/Zoom Scan (7x7x7)/Cube 1: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 9.88 V/m Peak SAR (extrapolated) = 0.332 W/kg SAR(1 g) = 0.138 mW/g; SAR(10 g) = 0.070 mW/g Maximum value of SAR (measured) = 0.159 mW/g A - 9 Date/Time: 2005/5/30 08:37:54 Test Laboratory: Advance Data Technology WUB-310A EVO N800C Horizontal Mode 2 11g DUT: Wireless 802.11g Portable USB Adapter ; Type: WUB-310A ; Test Frequency: 2412 MHz Communication System: 802.11g ; Frequency: 2412 MHz ; Duty Cycle: 1:1 ; Modulation type: OFDM Medium: MSL2450 Medium parameters used: f = 2412 MHz; σ = 1.98 mho/m; ε r = 54; ρ = 1000 kg/m 3 ; Liquid level : 150mm Phantom section: Flat Section ; Separation distance : 9 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Low Channel 1/Area Scan (5x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.121 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 7.22 V/m Peak SAR (extrapolated) = 0.210 W/kg SAR(1 g) = 0.109 mW/g; SAR(10 g) = 0.060 mW/g Maximum value of SAR (measured) = 0.118 mW/g A - 10 Date/Time: 2005/5/30 09:08:54 Test Laboratory: Advance Data Technology WUB-310A EVO N800C Horizontal Mode 2 11g DUT: Wireless 802.11g Portable USB Adapter ; Type: WUB-310A ; Test Frequency: 2437 MHz Communication System: 802.11g ; Frequency: 2437 MHz ; Duty Cycl…

Text truncated - open the document above for the full version.

B - 1 APPENDIX B: ADT SAR MEASUREMENT SYSTEM C - 1 APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION

FCC ID: SI5WUB310A Report No.: SA940317L181Report Format Version 2.0.1 SAR TEST REPORT REPORT NO.: SA940317L18 MODEL NO.: WUB-310A RECEIVED: Mar. 18, 2005 TESTED: May 30, 2005 ISSUED: Jun. 02, 2005 APPLICANT: U-MEDIA Communications, Inc. ADDRESS: 9F, No.1, Jin-shan 7th St., Hsinchu 300, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 31 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: SI5WUB310A Report No.: SA940317L182Report Format Version 2.0.1 Table of Contents 1.CERTIFICATION .........................................................................................................3 2.GENERAL INFORMATION..........................................................................................4 2.1 GENERAL DESCRIPTION OF EUT............................................................................4 2.2 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................5 2.3 GENERAL INOFRMATION OF THE SAR SYSTEM .............................................. ....5 2.4 GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION ..................9 3.DESCRIPTION OF TEST MODES AND CONFIGURATIONS ..................................13 4.DESCRIPTION OF SUPPORT UNITS ......................................................................14 5.TEST RESULTS ........................................................................................................15 5.1 TEST PROCEDURES ...............................................................................................15 5.2 MEASURED SAR RESULT .......................................................................................16 5.3 SAR LIMITS...............................................................................................................18 5.4 RECIPES FOR TISSUE SIMULATING LIQUIDS ......................................................18 5.5 TEST EQUIPMENT FOR TISSUE PROPERTY ........................................................20 6.SYSTEM VALIDATION ..............................................................................................21 6.1 TEST EQUIPMENT ...................................................................................................21 6.2 TEST PROCEDURE .................................................................................................21 6.3 VALIDATION RESULT...............................................................................................23 6.4 SYSTEM VALIDATION UNCERTAINTIES ................................................................24 7.MEASUREMENT SAR PROCEDURE UNCERTAINTIES.........................................25 7.1 PROBE CALIBRATION UNCERTAINTY ...................................................................25 7.2 ISOTROPY UNCERTAINTY......................................................................................25 7.3 BOUNDARY EFFECT UNCERTAINTY .....................................................................26 7.4 PROBE LINEARITY UNCERTAINTY ........................................................................26 7.5 READOUT ELECTRONICS UNCERTAINTY ............................................................26 7.6 RESPONSE TIME UNCERTAINTY...........................................................................27 7.7 INTEGRATION TIME UNCERTAINTY ......................................................................28 7.8 PROBE POSITIONER MECHANICAL TOLERANCE................................................28 7.9 PROBE POSITIONING .............................................................................................29 7.10 PHANTOM UNCERTAINTY ......................................................................................29 7.11 DASY4 UNCERTAINTY BUDGET.............................................................................30 8.INFORMATION ON THE TESTING LABORATORIES ..............................................31 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION FCC ID: SI5WUB310A Report No.: SA940317L183Report Format Version 2.0.1 1. CERTIFICATION PRODUCT : Wireless 802.11g Portable USB Adapter MODEL NO. : WUB-310A BRAND NAME : U-MEDIA APPLICANT : U-MEDIA Communications, Inc. TESTED : May 30, 2005 TEST SAMPLE : ENGINEERING SAMPLE STANDARDS : FCC Part 2 (Section 2.1093), FCC OET Bulletin 65, Supplement C (01-01), RSS-102 The above equipment has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY:, DATE:Jun. 02, 2005 ( Andrea Hsia ) TECHNICAL ACCEPTANCE :, DATE:Jun. 02, 2005 Responsible for RF ( Ansen Lei ) APPROVED BY :, DATE:Jun. 02, 2005 ( Cody Chang, Deputy Manager ) FCC ID: SI5WUB310A Report No.: SA940317L184Report Format Version 2.0.1 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT PRODUCT Wireless 802.11g Portable USB Adapter MODEL NO. WUB-310A POWER SUPPLY3.3Vdc from host equipment CLASSIFICATION Portable device, production unit MODULATION TYPE CCK, QPSK, BPSK for DSSS, 64QAM, 16QAM, QPSK, BPSK for OFDM RADIO TECHNOLOGY DSSS, OFDM TRANSFER RATE 802.11b: 11/5.5/2/1Mbps 8…

Text truncated - open the document above for the full version.

FCC ID: SI5WUB310A Report No.: RF940317L181Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF940317L18 MODEL NO.: WUB-310A RECEIVED: Mar. 18, 2005 TESTED: May 20 ~ May 23, 2005 ISSUED: May 26, 2005 APPLICANT: U-MEDIA Communications, Inc. ADDRESS: 9F, No.1, Jin-shan 7th St., Hsinchu 300, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 62 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: SI5WUB310A Report No.: RF940317L182Report Format Version 2.0.2 Table of Contents 1.CERTIFICATION ..................................................................................................... 4 2.SUMMARY OF TEST RESULTS ............................................................................. 5 2.1MEASUREMENT UNCERTAINTY .......................................................................... 5 3.GENERAL INFORMATION...................................................................................... 6 3.1GENERAL DESCRIPTION OF EUT........................................................................ 6 3.2DESCRIPTION OF TEST MODES.......................................................................... 7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ..................................................... 7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: ......................... 8 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 10 3.4DESCRIPTION OF SUPPORT UNITS .................................................................. 10 4.TEST TYPES AND RESULTS ............................................................................... 11 4.1CONDUCTED EMISSION MEASUREMENT ........................................................ 11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...................................... 11 4.1.2 TEST INSTRUMENTS........................................................................................... 11 4.1.3 TEST PROCEDURES ........................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 12 4.1.5 TEST SETUP ........................................................................................................ 13 4.1.6 EUT OPERATING CONDITIONS .......................................................................... 13 4.1.7 TEST RESULTS .................................................................................................... 14 4.2RADIATED EMISSION MEASUREMENT ............................................................. 20 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT........................................... 20 4.2.2 TEST INSTRUMENTS........................................................................................... 21 4.2.3 TEST PROCEDURES ........................................................................................... 22 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 22 4.2.5 TEST SETUP ........................................................................................................ 23 4.2.6 EUT OPERATING CONDITIONS .......................................................................... 23 4.2.7 TEST RESULTS .................................................................................................... 24 4.36dB BANDWIDTH MEASUREMENT .................................................................... 31 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................. 31 4.3.2 TEST INSTRUMENTS........................................................................................... 31 4.3.3 TEST PROCEDURE.............................................................................................. 32 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 32 4.3.5 TEST SETUP ........................................................................................................ 32 4.3.6 EUT OPERATING CONDITIONS .......................................................................... 32 4.3.7 TEST RESULTS .................................................................................................... 33 4.4MAXIMUM PEAK OUTPUT POWER .................................................................... 39 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT..................... 39 4.4.2 INSTRUMENTS..................................................................................................... 39 4.4.3 TEST PROCEDURES ........................................................................................... 40 4.4.4 DEVIATION FROM TEST STANDARD ................................................................. 40 4.4.5 TEST SETUP ........................................................................................................ 40 4.4.6 EUT OPERATING CONDITIONS .......................................................................... 40 4.4.7 TEST RESULTS .................................................................................................... 41 4.5POWER SPECTRAL DENSITY MEASUREMENT................................................ 42 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT ............................. 42 4.5.2 TEST INSTRUMENTS...........................................................................................…

Text truncated - open the document above for the full version.

FCC ID: SI5WUB310A Report No.: RF940317L1860Report Format Version 2.0.2 5. PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: SI5WUB310A Report No.: RF940317L1861Report Format Version 2.0.2 RADIATED EMISSION TEST