SRQ-V769MWCDMA Digital Mobile Handset

Android Mobile Phone User Manual The manual is applicable for the V769M mobile phone. Copyright © 2014 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice. Google, Android, Android Market, Google Mail are trademarks of Google, Inc. Other trademarks and trade names are the property of their respective owners. Third-party Software Statement When you install the software from a third-party, the phone might be restarted repeatedly or the software might not be used normally due to the incompatibility of the software itself. It is not the fault of the phone itself. Version 1.0 2014 -1- Using your phone Thanks for choosing the V769M, It’s a WCDMA Digital Mobile Phone, which will refer to as ‘phone’ from now on. Powered by Android TM , the phone supports 3G high-speed Internet access, which brings you brand new experiences. Don’t worry if the pictures we use to demonstrate your phone’s functions look a little different from what you see on the screen. It’s the functions that matter. -2- Before getting started Inserting and removing the SIM 1. Switch off your phone and disconnect any external power. 2. Remove the back cover and then the battery. 3. Hold your SIM on the cut corner, and slide it face down into the card holder. 4. Insert the battery. 5. Replace the back cover. Inserting a memory card 1. Remove the back cover. 2. Push tightly until the card is installed in the correct position and replace the back cover. -3- Using the battery Inserting the battery 1. Open the battery cover on the back of your phone. 2. Align the battery's contact points with those of the phone and gently press the battery down into place. 3. Replace the battery cover clicking it back into position. Removing the battery 1. Switch off your phone. 2. Open the battery cover. 3. Lift the battery up and out of your phone. -4- Charging the battery The battery is not fully charged when you unpack it for the first time. Please exhaust the capacity of the battery before you recharge it for the first time. To ensure the battery is always in its best condition, please charge the battery 8 hours for the first time and recharge it later at least 2 hours each time. 1. Connect the charger to the phone, and insert the charger to the standard power socket. 2. Please disconnect the charger from the power socket after the charging is completed. Tips:  To charge the battery, you can also connect the phone to the PC through the USB cable.  During charging, the phone and charger may normally become hot. -5- Touch screen Back key Home key Menu key Earpiece Camera Power key Volume keys Headset jack Front camera Microphone Speaker USB port Getting to know your phone -6- Descriptions of Keys Keys Functions Menu key Touch it to open a menu with items that affect the current screen or application. Home key Touch it to open the home screen. If you’re viewing the left or right extended home screen, Press it to open the central home screen. Back key Touch it to open the previous screen you were working in. If the onscreen keyboard is open, touch it to close the keyboard. Power key Press it to turn on/off the display. Long press it to open a menu with options for Airplane mode, for Silent mode, for Vibration mode, and for powering off and for rebooting the phone. Volume keys Adjust the volume. Long press it to quickly adjust the ring tone volume to maximum or minimum. -7- Onscreen icons Icon s Descriptions Icon s Descriptions Signal strength Full battery Charging Missed calls You have an unread message. You have an unread E-mail. In a call Music playing New calendar reminder Airplane mode Connected to a PC Alarm clock on Vibration mode Silent mode Wi-Fi function on Bluetooth ® function is on -8- Power on/off Powering on Long press the Power key until the power-on animation appears. Powering off Long press the Power key to display the phone options and select Power off. -9- Basic Operation Screen control You can control your phone through a series of operations on the screen.  Touch: you can touch the items on the screen to select them, to open the applications, or using the keyboard to input characters.  Swipe or slide: Quickly move your finger across the surface of the screen, without pausing when you first touch (so you don't drag something instead).  Touch & hold: you can touch & hold some items to get the item’s available menu.  Drag: you can drag some items on the screen to realize some operations.  Switch between landscape mode and portrait mode: you can switch to the landscape mode by rotating your phone. The landscape mode is only valid under some interfaces, such as text input interface, message viewing interface, etc.  Pinch: In some apps (such as Maps, Browser, and Gallery), you can zoom in and out by placing two fingers on the screen at once and pinching them together (to zoom out) or spreading them apart (to zoom in). -10- Home screen Arrange & work with apps To see all your apps, touch the All Apps Icon on any Home screen. After opening the All Apps, press an icon to enter the corresponding application. Touch the Back key to return to the previous screen. Touch the Home key to return to the home screen. From All Apps, you can:  Explore your widgets: Touch the widgets tab at the top of any All Apps screen.  Get more apps.: Touch the Play Store icon at the top of any All Apps screen. Favorites tray Status bar Shows the signal strength, battery status, etc. Notification bar Drag the notification bar down from the top of the screen to open the notifications panel. -11- Switch to a recently used application On the home screen, touch & hold the Home key, opens a list of thumbnail images of apps…

Text truncated - open the document above for the full version.

ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Date: February 24, 2014 Power of Attorney To whom it may concern, Please be notified that I, Zhang Min, have designated Ivy.Zhu in Shenzhen Morlab Communications Technology Co., Ltd. and David Gong in ZTE CORPORATION as the persons being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Ivy Zhu in Shenzhen Morlab Communications Technology Co., Ltd., and David Gong in ZTE CORPORATION on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: SRQ- V769M If you have any acknowledgement and response, please send it to Shenzhen Morlab Communications Technology Co., Ltd. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, Contact Person: 错误！未找到引用源。 Company: ZTE CORPORATION TEL: +86-21-68897541 FAX: +86-21-68891070 E-mail: [email protected]

ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: SRQ- V769M Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Schematics Block Diagram Parts List Operation Description Tune Up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Yours Sincerely, Zhang Min ZTE product approval manager

External Photos 1. EUT front view 2. EUT rear view 3. EUT left side view 4. EUT right side view 5. EUT top view 6. EUT bottom view

FCC label and label location 1. Label 2. Label location Label location

Internal Photos 1. EUT uncover view 2. Mainboard front view with shielding 3. Mainboard rear view with shielding 4. Mainboard front view without shielding 5. Mainboard rear view without shielding 6. GSM/WCDMA chip view 7. CPU chip view 8. BT/WIFI chip view 9. GSM/WCDMA antenna view 10. BT/WIFI antenna view 11. GPS antenna view

Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 2 of 166 DIRECTORY 1. TESTING LABORATORY .................................................................................................................... 4 1.1 IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION ................................................................... 4 1.2 ACCREDITATION CERTIFICATE .............................................................................................................. 4 1.3 LIST OF TEST EQUIPMENTS .................................................................................................................. 4 2. TECHNICAL INFORMATION .............................................................................................................. 5 2.1 IDENTIFICATION OF APPLICANT ............................................................................................................. 5 2.2 IDENTIFICATION OF MANUFACTURER ..................................................................................................... 5 2.3 EQUIPMENT UNDER TEST (EUT) .......................................................................................................... 5 2.3.1 PHOTOGRAPHS OF THE EUT ............................................................................................................. 6 2.3.2 IDENTIFICATION OF ALL USED EUT ..................................................................................................... 6 2.4 APPLIED REFERENCE DOCUMENTS ...................................................................................................... 6 2.5 DEVICE CATEGORY AND SAR LIMITS .................................................................................................... 6 2.6 TEST ENVIRONMENT/CONDITIONS ........................................................................................................ 7 3. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................. 8 3.1 INTRODUCTION .................................................................................................................................... 8 3.2 SAR DEFINITION .................................................................................................................................. 8 4. SAR MEASUREMENT SETUP ........................................................................................................... 9 4.1 THE MEASUREMENT SYSTEM ............................................................................................................... 9 4.2 PROBE ................................................................................................................................................ 9 4.3 PROBE CALIBRATION PROCESS ......................................................................................................... 11 4.3.1 DOSIMETRIC ASSESSMENT PROCEDURE .......................................................................................... 11 4.3.2 FREE SPACE ASSESSMENT PROCEDURE .......................................................................................... 11 4.3.3 TEMPERATURE ASSESSMENT PROCEDURE ....................................................................................... 11 4.4 PHANTOM .......................................................................................................................................... 12 4.5 DEVICE HOLDER ................................................................................................................................ 12 5. TISSUE SIMULATING LIQUIDS ........................................................................................................ 13 6. UNCERTAINTY ASSESSMENT ........................................................................................................ 15 Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 3 of 166 6.1 UNCERTAINTY EVALUATION FOR EUT SAR TEST ..................................................................... 15 6.2 UNCERTAINTY FOR SYSTEM PERFORMANCE CHECK ............................................................. 16 7. SAR MEASUREMENT EVALUATION ............................................................................................... 18 7.1 SYSTEM SETUP .................................................................................................................................. 18 7.2 VALIDATION RESULTS ........................................................................................................................ 19 8. OPERATIONAL CONDITIONS DURING TEST ................................................................................ 20 8.1 INFORMATION ON THE TESTING ........................................................................................................... 20 8.2 BODY-WORN CONFIGURATIONS .......................................................................................................... 21 8.3 MEASUREMENT PROCEDURE .............................................................................................................. 21 8.4 DESCRIPTION OF INTERPOLATION/EXTRAPOLATION SCHEME ................................................................ 21 9. MEASUREMENT OF CONDUCTED PEAK OUTPUT POWER ........................................................ 23 10. TEST RESULTS LIST ...................................................................................................................... 27 11. HOTSPOT MODE EVALUATION PROCEDURE ............................................................................ 32 12. MULTIPLE TRANSMITTERS EVALUATION ...........................................................................…

Text truncated - open the document above for the full version.

Report No.:SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd. Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 1. EUT Right Head Touch Cheek Position 2. EUT Right Head Tilt15 Position Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 2 of 7 3. EUT Left Head Touch Cheek Position 4. EUT Left Head Tilt15 Position Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 3 of 7 5. Side Position with earphone 6. Back Side Position 10mm 10mm Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 4 of 7 7. Face Side Position 8. Edge A 10mm 10mm Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 5 of 7 9. Edge B 10. Edge C 10mm 10mm Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 6 of 7 11. Edge D Liquid Level Photo Head Liquid Liquid depth: 15.1cm 10mm Report No.: SZ14010135S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 7 of 7 Liquid Level Photo Body Liquid Liquid depth :15.5cm

Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 2 of 135 TABLE OF CONTENTS 1. 1.1 EUT DESCRIPT ION.................................................................................................................................. GENERAL INFORMATION .................................................................................................................... 3 3 1.2 TES T STANDARDS AND RES U LTS............................................................................................................. 5 1.3 FACILI TI ES AND ACCREDITATIONS ........................................................................................................... 6 2. 2.1 CONDUCT ED RF OUTP UT POW ER ........................................................................................................... 47 CFR PART 2, PART 22H & 24E REQUIREMENTS ......................................................................... 7 7 2.2 PEA K TO AVERAGE RADIO .................................................................................................................... 19 2.3 99% OCCUPI ED BANDW IDTH................................................................................................................. 25 2.4 FREQUENCY STABIL IT Y ......................................................................................................................... 45 2.5 CONDUCT ED OUT OF BAND EMISSIONS................................................................................................. 51 2.6 BAND EDGE .......................................................................................................................................... 83 2.7 TRANSMI TT ER RADI AT ED POW ER (EIRP/ERP) ..................................................................................... 94 2.8 RADI AT ED OUT OF BAND EMISS IONS .................................................................................................. 104 Change History Issue Date Reason for change 1.0 2014-2-24 First edition Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 3 of 135 1. GENERAL INFORM ATION 1.1 EUT Description EUT Type ..............................: WCDMA Digital Mobile Handset Serial No................................: (n.a, marked #1 by test site) Hardware Version .................: V769M_V1B MB_A Software Version ...................: Applicant................................: Manufacturer .........................: V769M_VE Vtelca_1.00 ZTE Corporation ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China ZTE Corporation ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Frequency Range .................: GSM 850MHz: Tx: 824.20 - 848.80MHz (at inter vals of 200kHz); Rx: 869.20 - 893.80MHz (at intervals of 200kHz) GSM 1900MHz: Tx: 1850.20 - 1909.80MHz (at intervals of 200kHz); Rx: 1930.20 - 1989.80MHz (at inter vals of 200kHz) WCDMA 850MHz Tx: 826.4 - 846.6MHz (at intervals of 200kHz); Rx: 871.4 - 891.6MHz (at intervals of 200kHz) WCDMA 1900MHz Tx: 1852.4 - 1907.6MHz (at inter vals of 200kHz); Rx: 1932.4 - 1987.6MHz (at intervals of 200kHz) Modulation Type ....................: GSM,GPRS Mode with GMSK Modulation EDGE Mode with 8PSK Modulation WCDMA Mode with QPSK Modulation HSDPA Mode with QPSK Modulation HSUPA Mode with QPSK Modulation Multislot Class .......................: GPRS: Multislot Class12,EGPRS: Multislot Class12 Antenna Type ........................: PIFA Antenna Emission Designators ...........: GSM 850:249KG XW,GSM 1900:249KGXW EGPRS850:249KG7W, EGPRS1900:250KG7W, WCDMA 850:4M17F9W ,WCDMA1900:4M16F9W Note 1: The transmitter (Tx) frequency arrangement of the Cellular 850MHz band used by the EUT can be represented with the formula F(n)=824.2+0.2*(n-128), 128<=n<=251; the lowest, middle, highest channel numbers (ARFCHs) used and tested in this report are separately 128 (824.2MHz), 190 (836.6MHz) and 251 (848.8MHz). Note 2: The transmitter (Tx) frequency arrangement of the PCS 1900MHz band used by the E UT can be represented with the formula F(n)=1850.2+0.2*(n-512), 512<=n<=810; the lowest, middle and Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 4 of 135 highest channel numbers (ARFCHs) used and tested in this report are separately 512 (1850.2MHz), 661 (1880.0MHz) and 810 (1909.8MHz). Note 3: The transmitter (Tx) frequency arrangement of the WCDMA 850MHz band used by the EUT can be represented with the formula F(n)=826.4+0.2*(n-4132), 4132<=n<=4233; the lowest, middle and highest channel numbers (ARFCHs) used and tested in this report are separately 4132 (826.4MHz), 4175(835MHz) and 4233 (846.6MHz). Note 4: The transmitter (Tx) frequency arrangement of the WCDMA 1900MHz band used by the EUT can be represented with the formula F(n)=1852.4+0.2*(n-9262), 9262<=n<=9538; the lowest, middle and highest channel numbers (ARFCHs) used and tested in this report are separately 9262 (1852.4MHz), 9400 (1880MHz) and 9538 (1907.6MHz). Note 5: For a more detailed description, please refer to Specification or User ’s Manual supplied by the applicant and/or manufacturer. Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 5 of 135 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 2, Part 22 and Part 24 for the EUT FCC ID Certification: No. Identity Document Title 1 47 CFR Part 2 (10-1-0 9 Edition) …

Text truncated - open the document above for the full version.

Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 61 of 135 (Plot C3: EDGE 850MHz Channel = 251, 30MHz to 1GHz) (Plot C3.1: EDGE 850MHz Channel = 251, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 62 of 135 (Plot D1: EDGE 1900MHz Channel = 512, 30MHz to 1GHz) (Plot D1.1: EDGE 1900MHz Channel = 512, 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 63 of 135 (Plot D2: EDGE 1900MHz Channel = 661, 30MHz to 1GHz) (Plot D2.1: EDGE 1900MHz Channel = 661,1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 64 of 135 (Plot D3: EDGE 1900MHz Channel = 810, 30MHz to 1GHz) (Plot D3.1: EDGE 1900MHz Channel = 810, 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 65 of 135 (Plot E1: WCDMA850MHz Channel = 4132, 30MHz to 1GHz ) (Plot E1.1: WCDMA850MHz Channel = 4132, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 66 of 135 (Plot E2: WCDMA850MHz Channel = 4175, 30MHz to 1GHz) (Plot E2.1: WCDMA850MHz Channel = 4175, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 67 of 135 (Plot E3: WCDMA850MHz Channel = 4233, 30MHz to 1GHz) (Plot E3.1: WCDMA850MHz Channel = 4233, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 68 of 135 (Plot F1: WCDMA1900MHz Channel = 9262, 30 MHz to 1 GHz ) (Plot F1.1: WCDMA1900MHz Channel = 9262, 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 69 of 135 (Plot F2: WCDMA1900MHz Channel = 9400, 30MHz to 1GHz) (Plot F2.1: WCDMA1900MHz Channel = 9400, 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 70 of 135 (Plot F3: WCDMA1900MHz Channel = 9538, 30MHz to 1GHz) (Plot F3.1: WCDMA1900MHz Channel = 9538 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 71 of 135 (Plot G1: HSDPA 850MHz Channel = 4132, 30MHz to 1GHz) (Plot G1.1: HSDPA 850MHz Channel = 4132, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 72 of 135 (Plot G2: HSDPA 850MHz Channel = 4175, 30MHz to 1GHz) (Plot G2.1: HSDPA 850MHz Channel = 4175, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 73 of 135 (Plot G3: HSDPA850MHz Channel = 4233, 30MHz to 1GHz) (Plot G3.1: HSDPA850MHz Channel = 4233, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 74 of 135 (Plot H1: HSDPA1900MHz Channel = 9262, 30MHz to 1GHz) (Plot H1.1: HSDPA1900MHz Channel = 9262, 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 75 of 135 (Plot H2: HSDPA1900MHz Channel = 9400, 30MHz to 1GHz) (Plot H2.1: HSDPA1900MHz Channel = 9400, 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 76 of 135 (Plot H3: HSDPA1900MHz Channel = 9538, 30MHz to 1GHz) (Plot H3.1: HSDPA1900MHz Channel = 9538 1GHz to 20GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 77 of 135 (Plot I 1: HSUPA 850MHz Channel = 4132, 30MHz to 1GHz) (Plot I1.1: HSUPA 850MHz Channel = 4132, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 78 of 135 (Plot I 2: HSUPA 850MHz Channel = 4175, 30MHz to 1GHz) (Plot I2 .1: HSUPA 850MHz Channel = 4175, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 79 of 135 (Plot I 3: HSUPA850MHz Channel = 4233, 30MHz to 1GHz) (Plot I3.1: HSUPA850MHz Channel = 4233, 1GHz to 9GHz) Re port No.: SZ14010135W01 Shenzhen Morl…

Text truncated - open the document above for the full version.

Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 101 of 135 (Plot G: WCDMA 850 MHz Channel = 4132, 4175, 4233) (Plot H: HSDPA 850 MHz Channel = 4132, 4175, 4233) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 102 of 135 (Plot I: HSUPA 850 MHz Channel = 4132, 4175, 4233) (Plot J: WCDMA 1900 MHz Channel = 9262, 9400, 9538) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 103 of 135 (Plot K: HSDPA1900 MHz Channel = 9262, 9400, 9538) (Plot L: HSUPA1900 MHz Channel = 9262, 9400, 9538) Re port No.: SZ14010135W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.m orlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 104 of…

Text truncated - open the document above for the full version.