SS3-E2MTR2302DJI FlyCart 30

DJI FlyCart 30 Quick Start Guide Aircraft Over View 1.Propellers 2.Motors 3.Electronic Speed Controller 4.Front LEDs 5.Aircraft Arms 6.Binocular Vision System (Up) 7.Binocular Vision System (Down) 8. DJI Cellular Module 9.FPV Gimbal Camera 10.Spolight 11.Forward Phased Array Radar 12.Parachute 13.Intelligent Flight Battery 14.Weighing Sensor 15.Onboard Storage 16.Landing Gear 17.Rear Phased Array Radar 18.Video Transmitter Antennas 19.Rear LEDs 20.GNSS Antennas Remote Controller Over View 1. External Antennas 2. Touchscreen 3. Aircraft Authority Button 4. Control Sticks 5. Internal Wi-Fi Antennas 6. Back/Function Button 7. Return to Home (RTH) Button 8. Status LED 9. Battery Level LEDs 10. Internal GNSS Antennas 11. Power Button 12. 5D Button 13. Flight Pause Button 14. Reserved Button 15. Flight Mode Switch 16. Internal Antennas 17. microSD Card Slot 18. USB-A Port 19. HDMI Port 20. USB-C Port 21. Reserved Button 22. Battery Release Button 23. Battery Compartment 24. Rear Cover Release Button Using FC30 1. Charging Charging the DB2000 Intelligent Flight Battery Use C8000 Intelligent Battery Station to charge the DB2000 Intelligent Flight Battery. The C8000 Intelligent Battery Station needs to be activated before using for the first time, and the DB2000 Intelligent Flight Battery needs to be activated using C8000 Intelligent Battery Station. Charging the Remote Controller Use the DJI USB-C Power Adapter (100W) to charge the remote controller. The internal battery of the remote controller must to be charge to activate before using for the first time. The battery level LEDs start to flash to indicate the internal battery is activated and charging started. The remote controller cannot be powered on before activating the internal battery. 2. Prepare for the Remote Controller Checking Battery Level Press once on the power button to check the battery level when powered off. Powering On/Off Press once, press and hold on the power button to power on/off the remote controller. Follow the on-screen instructions to activate the remote controller before using for the first time. Adjusting the Antennas Lift and adjust the antennas. The strength of the remote controller signal is affected by the position of the antennas. 3. Prepare for the Aircraft Unfold the aircraft a. Unfold the M3 and M4 frame arms before unfold the M1 and M2 frame arms. Lock the arm lock for each frame arms. b. Remove the propeller holder. c. Unfold the propellers Installing the Intelligent Flight Battery Install the two batteries as shown. Press down the battery until you hear two click sound in sequence. Checking the Battery Level Check the battery level: press once on the power button. Power on/off: press once, and press and hold the power button. Activating the Aircraft Power on the aircraft and remote controller, launch DJI PILOT TM 2, and follow the on-screen instructions to activate the aircraft. Using the On-board Storage 5. Flight Manual take off/landing 1. Start/stop motors 2. Take off: push the throttle stick up to take off 3. Landing: pull the throttle stick down to land. Control the Aircraft The default control stick mode is Mode 2. The left control stick controls the altitude and heading of the aircraft while the right control stick controls the forward, backward, and sideward movements. Specifications Aircraft (Model：E2MTR-30A) Operating Frequency 2.4000-2.4835 GHz; 5.725-5.850 GHz Transmitter Power（EIRP） 2.4 GHz: <33 dBm (FCC) , <20 dBm (SRRC/CE/MIC) 5.8 GHz: <33 dBm (FCC), <23 dBm (SRRC), <14 dBm (CE) RTK/GNSS Operating Frequency RTK: GPS L1/L2, GLONASS F1/F2, BeiDou B1I/B2I/B3I, Galileo E1/E5b, QZSS L1/L2 GNSS：GPS L1, GLONASS F1, BeiDou B1I, Galileo E1, QZSS L1 Operating Temperature -20°C to 45°C •Forward Phased Array Radar（Model：RD241608RF） Operating Frequency 24.05-24.25 GHz (NCC/FCC/MIC/KC/CE) Power Consumption 23 W Transmitter Power（EIRP） <20 dBm (NCC/MIC/KC/CE/FCC) Operating Voltage DC 15 V Operating Temperature -20°C to 45°C •Rear Phased Array Radar（Model：RD241608RB） Operating Frequency 24.05-24.25 GHz (NCC/FCC/MIC/KC/CE) Power Consumption 18 W Transmitter Power（EIRP） <20 dBm (NCC/MIC/KC/CE/FCC) Operating Voltage DC 15 V Operating Temperature -20°C to 45°C •Remote Contorller（Model：RM700B） Internal Battery Li-ion (6500 [email protected] V) O3 Operating Frequency 2.4000-2.4835 GHz; 5.725-5.850 GHz Transmitter Power（EIRP） 2.4 GHz: <33 dBm (FCC), <20 dBm (CE/SRRC/MIC) 5.8 GHz: <33 dBm (FCC), <14 dBm (CE), <23 dBm (SRRC) Wi-Fi Protocol Wi-Fi 6 Operating Frequency 2.4000-2.4835 GHz; 5.150-5.250 GHz; 5.725-5.850 GHz Bluetooth Protocol Bluetooth 5.1 Operating Frequency 2.4000-2.4835 GHz Transmitter Power（EIRP） <10 dBm Compliance Information FCC Compliance Notice Supplier’s Declaration of Conformity Product name: DJI FlyCart 30 Model Number: E2MTR-30A Responsible Party: DJI Research LLC Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306 Website: www.dji.com We, DJI Research LLC, being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran…

Text truncated - open the document above for the full version.

Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name SZ DJI TECHNOLOGY CO., LTD Address Lobby of T2, DJI Sky City, No 53 Xianyuan Road, Xili Community,Xili Street,Nanshan District,Shenzhen, China Grantee Code SS3 FCC ID SS3-E2MTR2302 Authorized Contact Name Gary Zeng Contact Email [email protected] Contact Phone 8675586152250 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List [SZ DJI TECHNOLOGY CO., LTD] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [SZ DJI TECHNOLOGY CO., LTD] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date:2023-06-05 Print Name: Gary Zeng Title: PM *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

UNITED STATES DESIGNATED AGENT LETTER Date: 2023-06-06 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant U.S. designated agent Company Name: SZ DJI TECHNOLOGY CO., LTD Company Name: DJI Research LLC Grantee Code: SS3 FRN: 0033569757 Contact Name: Gary Zeng Contact Name: Jie Shen Address: Lobby of T2, DJI Sky City, No 53 Xianyuan Road, Xili Community,Xili Street,Nanshan District, Address: 435 Portage Ave, Palo Alto, CA 94306 City/Province/Zip: Shenzhen City/Province/Zip: Palo Alto/California/94306 Telephone: 8675586152250 Telephone: 530-574-9905 Fax: +86 755 86965903 Fax: Email: [email protected] Email: [email protected] ATTN: Director of Certification: We, < SZ DJI TECHNOLOGY CO., LTD > and < DJI Research LLC > understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < SZ DJI TECHNOLOGY CO., LTD > and < DJI Research LLC > acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Gary Zeng Name (Printed): Jie Shen Title: PM Title: General Manager Signature: Signature:

SZ DJI TECHNOLOGY CO., LTD Date: 2023-09-19 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: SS3-E2MTR2302 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) and Keny Xu in SGS- CSTC Standards Technical Services Co., Ltd. (SGS) to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own.. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with SZ DJI TECHNOLOGY CO., LTD. This authorization is valid until further written notice from the applicant. Print Name: Gary Zeng Title: PM Signature: On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: [email protected]

SZ DJI TECHNOLOGY CO., LTD TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: SS3-E2MTR2302 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions BOM List Software Security Description The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Gary Zeng Title: PM Signature: On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 1 of 8 Appendix External Photos for SZCR2308002559AT FCC ID: SS3-E2MTR2302 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 2 of 8 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 3 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 4 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 5 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 6 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 7 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 8 of 8 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 1 of 10 Appendix Internal Photos for SZCR2308002559AT FCC ID: SS3-E2MTR2302 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 2 of 10 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 3 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 4 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 5 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 6 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 7 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 8 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 9 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 10 of 10 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 1 of 10 Keny Xu EMC Laboratory Manager 1 Cover Page Test Report Application No.: SZCR2308002559AT Applicant: SZ DJI TECHNOLOGY CO., LTD. Address of Applicant: Lobby of T2, DJI Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China. Manufacturer: SZ DJI TECHNOLOGY CO., LTD. Address of Manufacturer: Lobby of T2, DJI Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China. Equipment Under Test (EUT): EUT Name: DJI FlyCart 30 Model No.: E2MTR-30A Trade Mark: DJI FCC ID: SS3-E2MTR2302 Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2023-08-08 Date of Test: 2023-08-18 to 2023-09-08 Date of Issue: 2023-09-18 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 2 of 10 Revision Record Version Chapter Date Modifier Remark 01 2023-09-18 Original Authorized for issue by: Darren Yuan/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 3 of 10 2 Contents Page 1 Cover Page .................................................................................................................................. 1 2 Contents ...................................................................................................................................... 3 3 General Information..................................................................................................................... 4 3.1 General Description of E.U.T. ................................................................................................ 4 3.2 Details of E.U.T. .................................................................................................................... 4 3.3 Test Location ........................................................................................................................ 8 3.4 Test Facility ........................................................................................................................... 8 4 FCC Radiofrequency radiation exposure limits ......................................................................... 9 5 Measurement and Calculation .................................................................................................. 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 4 of 10 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. Power supply: Powered by Lithium-Ion Polymer Rechargeable Battery Battery Information Model: BAX101-38000mAh-52.22V Nominal Voltage: 52.22V Rated Capacity: 38000mAh, 1984.4Wh SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 5 of 10 2.4G SDR Operation Frequency: 1.4MHz: 2403.5MHz-2469.5MHz and 2405.12MHz-2479.12MHz 3MHz: 2405.5MHz-2468.5MHz and 2408.2MHz-2471.2MHz 10MHz: 2407.5MHz-2467.5MHz 20MHz: 2412.5MHz-2462.5MHz 40MHz: 2422.5MHz-2452.5MHz Modulation Type: OFDM Channel Spacing: 1.4MHz: 2MHz 3MHz: 3MHz 10MHz: 1MHz 20MHz: 1MHz 40MHz: 1MHz Number of Channels: 1.4MHz: 72 3MHz: 44 10MHz: 61 20MHz: 51 40MHz: 31 Antenna Type: PIFA Antenna Antenna Gain: ANT0&ANT1&ANT2&ANT3: 4.5dBi SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 6 of 10 5.8G SDR Operation Frequency: 1.4MHz: 5728.5MHz-5846.5MHz and 5730.12MHz-5848.12MHz 3MHz: 5727.5MHz-5844.5MHz and 5730.2MHz-5847.2MHz 10MHz: 5730.5MHz-5844.5MHz 20MHz: 5735.5MHz-5839.5MHz 40MHz: 5745.5MHz-5829.5MHz Modulation Type: OFDM Channel Spacing: 1.4MHz: 2MHz 3MHz: 3MHz 10MHz: 1MHz 20MHz: 1MHz 40MHz: 1MHz Number of Channels: 1.4MHz: 120 3MHz: 80 10MHz: 115 20MHz: 105 40MHz: 85 Antenna Type: PIFA Antenna Antenna Gain: ANT0&ANT1&ANT2&ANT3: 4dBi SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 7 of 10 Forward Phased Array Radar (RD241608RF), it includes single board radar and omnidirectional radar Operation Frequency: 24.00GHz to 24.25GHz Modulation: FMCW Antenna type: Linear Antenna Antenna Gain: 10dBi (Provided by the manufacturer) Rear Phased Array Radar (RD241608RB) Operation Frequency: 24.00GHz to 24.25GHz Modulation: FMCW Antenna type: Linear Antenna Antenna Gain: 10dBi (Provided by the manufacturer) Remark:The information in this section is provided by the applicant or manufacturer, SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. Separation Distance Minimum test separation distance: 20cm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255904 Page: 8 of 10 3.3 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 1 of 188 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2308002559AT Applicant: SZ DJI TECHNOLOGY CO., LTD. Address of Applicant: Lobby of T2, DJI Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China. Manufacturer: SZ DJI TECHNOLOGY CO., LTD. Address of Manufacturer: Lobby of T2, DJI Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China. Equipment Under Test (EUT): EUT Name: DJI FlyCart 30 Model No.: E2MTR-30A Trade Mark: DJI FCC ID: SS3-E2MTR2302 Standard(s) : 47 CFR Part 15, Subpart E 15.407 Date of Receipt: 2023-08-08 Date of Test: 2023-08-18 to 2023-09-08 Date of Issue: 2023-09-18 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 2 of 188 Revision Record Version Chapter Date Modifier Remark 01 2023-09-18 Original Authorized for issue by: Darren Yuan/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 3 of 188 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart E 15.407 N/A 47 CFR Part 15, Subpart C 15.203 Pass Transmission in the Absence of Data N/A 47 CFR Part 15, Subpart E 15.407 (c) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Duty Cycle 47 CFR Part 15, Subpart E 15.407 KDB 789033 II B 1 KDB 789033 D02 II B 1 Pass 99% Bandwidth KDB 789033 II D N/A Pass Minimum 6 dB bandwidth (5.725- 5.85 GHz band ) KDB 789033 D02 II C 2 47 CFR Part 15, Subpart E 15.407 (e) Pass Maximum Conducted output power KDB 789033 D02 II E 47 CFR Part 15, Subpart E 15.407 (a) Pass Peak Power spectrum density KDB 789033 D02 II F 47 CFR Part 15, Subpart E 15.407 (a) Pass Radiated Emissions which fall in the restricted bands KDB 789033 D02 II G 47 CFR Part 15, Subpart C 15.209 & Subpart E 15.407(b) Pass Radiated Emissions (Above 1GHz) KDB 789033 D02 II G 47 CFR Part 15, Subpart C 15.209 & Subpart E 15.407(b) Pass Radiated Emissions (Below 1GHz) KDB 789033 D02 II G 47 CFR Part 15, Subpart C 15.209 & Subpart E 15.407(b) Pass Frequency Stability ANSI C63.10 (2013) Section 6.8 47 CFR Part 15, Subpart E 15.407 (g) Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 4 of 188 3 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Test Summary ........................................................................................................................................... 3 3 Contents .................................................................................................................................................... 4 4 General Information .................................................................................................................................. 6 4.1 Details of E.U.T. ................................................................................................................................. 6 4.2 Description of Support Units .............................................................................................................. 6 4.3 Measurement Uncertainty .................................................................................................................. 7 4.4 Test Location ...................................................................................................................................... 8 4.5 Test Facility ........................................................................................................................................ 8 4.6 Deviation from Standards ................................................................................................................... 8 4.7 Abnormalities from Standard Conditions ........................................................................................... 8 5 Equipment List .......................................................................................................................................... 9 6 Radio Spectrum Technical Requirement ............................................................................................. 13 6.1 Antenna Requirement ...................................................................................................................... 13 6.1.1 Test Requirement: ....................................................................................................................... 13 6.1.2 Conclusion ................................................................................................................................... 13 6.2 Transmission in the Absence of Data .............................................................................................. 14 6.2.1 Test Requirement: ....................................................................................................................... 14 6.2.2 Conclusion ................................................................................................................................... 14 7 Radio Spectrum Matter Test Results .................................................................................................... 15 7.1 Duty Cycle ........................................................................................................................................ 15 7.1.1 E.U.T. Operation ............................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 107 of 188 3M_HCH_5847.2MHz_Ant0_NTNV 3M_HCH_5847.2MHz_Ant1_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 108 of 188 3M_HCH_5847.2MHz_Ant2_NTNV 3M_HCH_5847.2MHz_Ant3_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 109 of 188 10M_LCH_5730.5MHz_Ant0_NTNV 10M_LCH_5730.5MHz_Ant1_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 110 of 188 10M_LCH_5730.5MHz_Ant2_NTNV 10M_LCH_5730.5MHz_Ant3_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 111 of 188 10M_MCH_5787.5MHz_Ant0_NTNV 10M_MCH_5787.5MHz_Ant1_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 112 of 188 10M_MCH_5787.5MHz_Ant2_NTNV 10M_MCH_5787.5MHz_Ant3_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 113 of 188 10M_HCH_5844.5MHz_Ant0_NTNV 10M_HCH_5844.5MHz_Ant1_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 114 of 188 10M_HCH_5844.5MHz_Ant2_NTNV 10M_HCH_5844.5MHz_Ant3_NTNV SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230800255903 Page: 115 of 188 2…

Text truncated - open the document above for the full version.