SS3-GL6581502C1

User Manual Compliance Information KCC Warning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.” “해당 무선설비는 운용 중 전파혼신 가능성이 있음” In the Box Check that all of the following items have been included in your package before use. If anything is missing, please contact your local dealer. Index Name Picture Qty. 1 DJI Inspire 1 1 2 Propeller 4 3 C1 1 4 Camera with gimbal 1 5 Smart Battery 1 6 Battery Charger 1 Introduction DJI Inspire 1 package includes aircraft, C1, gimbal, camera and DJI App. Flight control system is inside the aircraft, the built‐in camera has been integrated with gimbal. C1 and DJI App are used to control the aircraft, gimbal and camera. The HD video downlink and receiver have been integrated in the aircraft, which is used for HD video transmitter and control the aircraft. Features: ‐Equipped with retractable landing gear, and unobstructed 360 degree view from the camera is made possible by simply moving the landing gear out of sight. The maximum flight height of DJI Inspire 1 is **, the maximum distance is **. DJI Inspire 1 has a battery capacity of 6S, 4500mAh. When the battery is fully charged, it has a maximum run time of **. ‐ The camera is using a 21mm bugeye lens, which has low optical distortion and high resolution. Video output can be achieved at HD 4Kp30@60Mbps and it supports many kinds of filters. A high performance gimbal enables to obtain stable images even when the aircraft is fling in high speed. －Integrated the advanced flight controller of DJI, the DJI Inspire 1 has stable performance during flight. It can automatically fly back when the C1 signal was missed. The hover assistant enable the DJI Inspire 1 to hover stable without GPS. ‐ The HD video downlink has been integrated inside the aircraft, which is used with DJI App to display real time HD aerial image, aircraft data and camera data on the mobile device. In addition, it provides ground station function which allows users to plan the flight mission and enables aircraft to flight automatically. Flight safety In GPS mode, the aircraft can be positioned accurately and hover stably, and the return home function is available. (Orientation of aircraft is under control but it could not avoid obstructer automatically). Hover assistant makes aircraft hover stable without GPS (hover assistant can work properly below height of 5m, and the floor surface have pattern variations in good light conditions). Airc GL6 [1] A [2] M [3] S [4] N [5] R [6] T [7] B [8] S [9] P [10] [11] raft 58A Antenna Mounting Po Stick Neck Strap A RTH Button Transformati Battery Leve Status LED Power Button Camera Sett Playback Bu osition Attachment ion Switch el LEDs n tings Dial utton [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] Built‐in G Propeller Motor Front L E Landing Frame a r Gimbal DJI Sma r Micro‐US Rear LED Camera M Camera M Port Hover a s GPS r ED gear rm rt Battery SB Port D Micro‐USB P Micro‐SD C ssistant cam Port ard era [12] Shutter Button [13] Flight Mode Switch [14] Video Recording Button [15] Gimbal Dial [16] HDMI Port [17] Upgrade Port [18] CAN Port [19] USB Port [20] Handle Bar [21] Reserved Button [22] Power Source Port [23] Reserved Button Start 1. Watch the tutorial video Scan the QR code or click the link shown below to watch the tutorial video. Tutorial video http://www.dji.com/Inspire1/training 2. Download DJI App Search ʺDJI” on the App Store then follow instructions for iOS version. Search ʺDJIʺ on Google Play then follow instructions for Android version. Register your e‐mail address when using the app for the very first time. App Store Google Play 3. Ensure the smart battery\C1 and the mobile device are fully charged. Please charge the device if it has low battery level. Important: Please watch the tutorial and read the quick start guide fully before using your DJI Inspire 1. * For the best experience, install and use the DJI App on tablet. ** See Appendix for checking battery levels. Refer to user manual for charging。 DJI App There are four page of GUI: Camera, ground station, tool box and user center. [1] Present flight mode [2] GPS signal status [3] Aircraft status [4] RC settings [5] HD video downlink settings [6] Smart battery information [7] General settings [8] Photo format [9] Video format/Recording time [10] Shutter/Record switch [11] Shutter/Record [12] Play back [13] Camera settings [14] Ground station [15] Aircraft orientation/Height/Distance [16] Home point settings [17] Return home [18] Gimbal mode [19] Take off Camera GUI: For display the real time HD images and aircraft data, enable shutter and video recording. Ground Station: For display the map for setting flight mission. User Center: photograph and video synchronization, flight record, DJI Shop and account information. Preparing DJI Inspire 1 1. Mounting the Gimbal Step 1：Remove the Gimbal Cover and the Gimbal Clamp from the gimbal. Step 2：Turn the Gimbal Lock to the right (when you are facing the nose of the DJI Inspire 1) until it locks in place and you hear a clicking sound. Refer to the picture below for details: Step 3: Insert the gimbal into the Gimbal Lock. Ensure the white mark on the gimbal is aligned with the white mark on the left of the Gimbal Lock. Refer to the picture below for details: Step 4: With the gimbal in place, turn the Gimbal Lock to the left (when you are facing the nose of the DJI Inspire 1) until it locks in the position shown in the below. Now the gimbal is secured: 2. Attaching the Propellers Screw the propellers, clockwise for grey nuts and anti‐clockwise for black nuts, onto the four motors. Be sure to match the black propeller nuts with the black dot motors. Important：Make sure your smart flight battery and Micro‐SD care are inserted correctly. 3. Description of Aircraft Port （See the location on P） Micro‐USB Port: For connecting aircraft and PC Assistant to upgrade firmware. Camera Micro‐ USB Port: For connecting aircraft and PC to output the data to PC. Camera Micro‐SD Card Port: For p…

Text truncated - open the document above for the full version.

2 ） L RTH USB HDM Upg CAN 3. C o S S S Lower: The l Deforma H Button：P The ent Poi con B Port: Conn aircraf MI Port: Con cam grade Port: U fir yo N Port: Rese onnecting Mob Step 1: Positio mount Step 2: Attach t Step 3: Press th landing gear ation of aircraf Press and ho e LED arou tering RTH int. Press th ntrol of the a nect your mo ft features av nnect an HD mera sees in f Use this port rmware. The our compute erved for fut bile Device an on the mobile ting hole and t the holder to n he button on th r will lower ft on the groun old this butt nd the RTH mode. The a his button a aircraft. obile device vailable in th D compatibl full HD. t to connect e relevant A er. ture use. nd C1 e device hold tighten the scr neck strap atta he side to hold to its lowest nd do not use ton to start H Button wil aircraft will gain to can c to the USB P he DJI app. e monitor t o the GL658A Assistant soft der as the pic rew. achment and t d the mobile d t position fo function, so a the Return ll blink whi then return cel the RTH Port to acces o the HDMI A to a PC or tware must b cture shown, tighten. device and sec or landing. as not to dam to Home (R ite to indica n to the last H procedure ss all of the port to see w Mac and up be installed then plug th cure. age the came RTH) proced ate the aircra recorded H e and regain camera and what your pgrade the and open o n he holder into ra. dure. aft is Home n the n o the Step 4: Connect the mobile device to C1 USB port via micro‐USB cable. 4. Powering on C1 Press the power button once to check the current battery level. Press once and then press again and hold for 2 seconds to power on the C1. (Repeat the above steps again to power off the C1) Ready to Fly 1. Place the aircraft on flat ground in an open place with rear LED flight indicators facing you, and then power on the C1 and aircraft. 2. Connect C1 and mobile device. 3. Launch DJI App, make sure the GPS mode has been selected. 4. Calibrating Compass Always calibrate compass before your flight. Step 1: Go into the App camera GUI and tap the button, select “calibrate compass” to start the process, the rear LED flight indicator will be solid blue at this time. Step 2: Hold aircraft horizontally then rotate 360° around the center axis until rear LED flight indicator will be solid green. Step 3: Hold aircraft vertically with nose pointing to the ground, rotate 360° around the center axis until rear LED flight indicator will be blink purple. The process is completed. If rear LED flight indicator is solid red, calibration has failed. Re‐calibrate by repeating step 1‐3. 5. Description of rear LED indicator Blinking purple：GPS〉＝6 or hover assistant is functioning，it is safe for flight. Blinking yellow: No GPS protection. Blinking red: System error occurs. * Refer to Appendix for more information. 6. Go into the camera GUI and tap check list, ensure everything is functioning normal. Flight 1. Taking off：Start motors by pulling both control sticks to the bottom corners. Release sticks once motors start. Slowly push the left(throttle) stick up to take off. Landing：Switch the transformation switch to lower position before landing. Gently pull the left (throttle) stick down to lower the aircraft until it touches the ground. When landing on the ground, pull the throttle stick to the bottom, then pull both sticks to bottom corners to stop motors. Power off the aircraft prior to power off the C1. 2. C1 Operation This section explains how to use the various features of the C1. C1 (Mode 2) Aircraft ( indicates nose direction) Remarks Moving the left stick up and down changes the aircraft’s elevation. Push the stick up to ascend and down to descend. Push the throttle stick up to takeoff. When both sticks are centered, the DJI Inspire 1 will hover in place. The more the stick is pushed away from the center position, the faster the DJI Inspire 1 will change elevation. Always push the stick gently to prevent sudden and unex pected elevation changes. Moving the left stick to the left or right controls the rudder and rotation of the aircraft. Push the sick left to rotate the aircraft counter clock‐wise, and push the stick right to rotate the aircraft clockwise. If the stick is centered, the DJI Inspire 1 will stay facing its current direction. The more the stick is pushed away from the center position, the faster the DJI Inspire 1 will rotate. Moving the right stick up and down changes the aircraft’s forward and backward pitch. Push the stick up to fly forward and down to fly backward. The DJI Inspire 1 will hover in place if the stick is centered. Push the stick further away from the center 3. Re P th Aer i 1. Se butto tilt a 2. Se can a 3. Sy Ap p eturn Home Press and hold he return hom It is reco Do not s ial Photograph et the part of on\record but angle of gimb et all of the ca also be use wh ynchronize th pendix d the return ho me procedure i ommend to ta stop the moto h f camera para tton and play al by using th amera parame hen you are u e SD card dat ome button for is in process. P ake off the airc r during fligh ameter throug y back button he gimbal dial eter, control ca using ground ta to mobile d position and fast Moving changes Push lef Inspire 1 Push th position and fast Gimbal camera to the l downw current r a while until Press once to s craft until the r ht. gh the camera to shutter\re l. amera to shut station functi device. n for a large ter flight. the right s the aircraft’ ft to fly left 1 will hover he stick fu n for a large ter flight. Dial: Turn will shift to left, and th ards. The position wh l the LED surr stop the proce rear LED light a setting butt cording and p tter \recording ion. er pitch ang stick contr ’s left and rig and right to in place if th rther away er pitch ang the dial to o point upw he camera w camera w hen dial is st round the butt edure. t blinks purple ton on the C preview the p g and play ba gle (maximu rol left and ght pitch. o fly right. T he stick is cen y from the gle (maximu the r…

Text truncated - open the document above for the full version.

PERMANENT AND SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Circuit Description 3 Schematic SHORT-TERM 4 External and Internal Photos 5 Test-Setup Photos 6 User Manual SZ DJI TECHNOLOGY CO., LTD. Add:14th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave, Nanshan, Shenzhen, Guangdong ,China Tel: 0755‐86152250 Fax: 0755-86965903 Date: 2015-2-3 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 RE: Request of confidentiality for FCC ID: SS3-GL6581502 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, SZ DJI TECHNOLOGY CO., LTD.hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give SZ DJI TECHNOLOGY CO., LTD. temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows: The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, Signature: Lisa Li Certification Supervisor

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT – Top View EUT – Bottom View EUT – Side View EUT – Side View

EXHIBIT A - FCC ID LABELING AND LOCATION FCC ID Label Proposed FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Label Here

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Uncover View EUT –Uncover View EUT – HDMI Top View EUT –HDMI Bottom View EUT – Uncover View EUT – Port Top View EUT – Port Bottom View EUT –Uncover View EUT – Uncover View EUT – Main Board Top View EUT –Main Board Bottom View EUT –Main Board Top Unshielded View EUT –2.4G Circuit View EUT – Uncover View EUT –5.8G RF Module Top View EUT –Unshielded View EUT –5.8G RF Module Bottom View EUT –Antenna View EUT –Battery Top View EUT –Battery Bottom View

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15.247 TEST REPORT For SZ DJI TECHNOLOGY CO., LTD 14th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave, Nanshan, Shenzhen, Guangdong, China Report Type: Original Report Product Type: Remote Controller Test En gineer: Allen Qiao Re port Number: RDG150203002-00A Re port Date: 2015-02-11 Reviewed B y: Sula Huang RF Engineer Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn FCC ID: SS3-GL6581502 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG150203002-00A FCC Part 15.247 Page 2 of 24 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 4 TEST METHODOLOGY .................................................................................................................................................. 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 5 SUMMARY OF TEST RESULTS ............................................................................................................................... 6 FCC §15.247 (i) & §1.1310 & §2.1093- RF EXPOSURE ............................................................................................... 7 APPLICABLE STANDARD .............................................................................................................................................. 7 FCC §15.203 - ANTENNA REQUIREMENT ............................................................................................................. 8 APPLICABLE STANDARD .............................................................................................................................................. 8 ANTENNA CONNECTOR CONSTRUCTION ...................................................................................................................... 8 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS ............................................................................... 9 APPLICABLE STANDARD .............................................................................................................................................. 9 MEASUREMENT UNCERTAINTY .................................................................................................................................... 9 EUT SETUP .................................................................................................................................................................. 9 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP .............................................................................................. 10 TEST PROCEDURE ...................................................................................................................................................... 10 CORRECTED AMPLITUDE & MARGIN CALCULATION ................................................................................................. 11 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 11 TEST RESULTS SUMMARY .......................................................................................................................................... 11 TEST DATA ................................................................................................................................................................ 11 FCC §15.247(a) (2) – 6dB BANDWIDTH.................................................................................................................. 15 APPLICABLE STANDARD ............................................................................................................................................ 15 TEST PROCEDURE ...................................................................................................................................................... 15 TEST EQUIPMENT LIST AND DETAILS ...............................................................................................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View