SS4BIP6000MAXIDRFID Reader

BIP-6000 1 www.bluebirdsoft.com FCC (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technical for help. – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technical for help. – WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept ant interference received, including interference that may cause undesirable operation. PIDION aims for leading brand in the future mobile industry. As a global brand representing the image of reliability, representativeness, and cutting-edge technologies, this mark has been registered by Bluebird Soft Inc. around the world to be protected under trademark-related laws. ※ Please read warnings and cautious before use. Device typeUser’s guidance A-level (IT device at work) This device is registered as suitable for electromagnetic wave use at workplace. It should be appropriately considered by dealers or users. If you sell or buy this device by mistake, please replace it with a product for home use. Type registration This wireless device may cause propagation interference, and so, it cannot be used for life-saving services. User’s guidance Trademark This User’s Manual is protected under the related copyright laws. This User’s Manual is produced by Bluebird Soft Inc. The company has made every effort to avoid errors and omissions. Please understand that some parts may not reflect the actual state. The supplied basic programs are protected under. Reproduction, transfer or deletion of the programs without prior consent is strictly prohibited. Depending on users’ environments, programs or peripherals, some parts of this Product may not work normally. This wireless device may cause propagation interference, and so, it cannot be used for life-saving services. Copyright BIP-6000 1 Contents 2 Safety Instructions I 3 Safety Instructions II 4 About the product 1. Checking components 2. Checking names of parts 3. Buttons 4. Features 5. Communication spec. 12 Learning basics 1. Mounting/Dismounting battery 2. Inserting/Removing USIM/USAM card 3. Setting password 4. Inserting/removing MicroSD card 5. Charging a terminal with a desktop charger 6. How to use 4Slot Cradle 7. About battery 8. Switching On/Off power 9. Communication status indication 5. Managing Delected Items 6. Managing Sent Messages 49 Camera 1. Taking photos 2. Viewing album 52 Settings 1. Setting personal environment 2. Setting system environment 3. Setting connection environment 67 Value Pack Details 70 Q & A 71 Knowing the product 73 Customer Service 74 Service Center Information 76 Warranty Certificate 38 Inputting text 1. Selecting Text Input Mode 2. Block Recognizer 3. Key Pad 4. Keyboard 5. Letter Recognizer 6. Transcriber 41 Phone program 1. Making a call 2. Receiving a call 3. Rejecting calls 4. Ending calls 43 Phonebook 1. Searching phonebook 2. Registering entry 3. Viewing menu 46 Text Message 1. Creating a Text Message 2. Sending a Text Message 3. Viewing Text Messages 4. Managing Draft Messages 10. Adjusting screen 11. Using stylus pen 12. Using earjack 13. Resetting terminal 14. Hard-resetting 15. Using IrDA 28 Using USB cable 29 Connecting ActiveSync 1. Installing ActiveSync 2. Using ActiveSync 34 Using barcode reader 1. Using barcode 2. Scanning barcode 3. Reading barcode 36 Today Screen 1. Viewing Today Screen 2. Setting photo image as the background image 3. Adjusting volume 4. Checking battery 2 BIP-6000 Manual Read these instructions and warnings to use the Product in a safe manner and to prevent accidents. Cautions in relation with batteries Batteries may explode when damaged, impacted, heated, flooded or taken apart with a gimlet. Make sure to keep the batteries out of reach of children or pets. Do not use the Product in the area with the risk of explosion. If the Product is wet, do not put it in a device that may heat the terminal (heater, microwave oven, etc.). Heating batteries may cause an explosion, deformation or fault. (Water or any other liquid will change the color of the label inside the terminal. In this case, no warranty service will be provided.) Safety Guideline Do not use the Product on an airplane or in a hospital. Do not operate the Product or search a phone number while driving a car. If it is unavoidable, please use a hands-free kit or stop the car. Batteries may become deformed and get in …

Text truncated - open the document above for the full version.

MACQM7 ITEM PA RT MOD E REVIS ISSUE LAST ACKNOW 730-06 REV.0 A : Quadr NAME : EL NAME SION : 0 E DATE : SAVED : BUYER WLEDGED BY 0 CERAMI APP ME rifilar M MQMA 6 E : BIP-6 May 0 4 : May 04 R : 아이디로 M ICS ＆ RF COMPO ROV ESSRS eander A 60SH939 6000 (KO 4, 2012 4, 2012 로(주) MAC technol ONENTS FOR TEL VAL . 아이 Antenna -A OREA) D ogies Inc. ECOMMUNICATIO L SH 이디로 a SUPPLIER DRAWN # 301, O N SYSTEMS HEE (주) R : MAC tech CHECKED Star enterprise cent Ochang-eub, Cheong Tel : +8 A4 (2 ET hnologies Inc D APP ter, Technopark, 685 gwon-gun, Chungbuk 2 43 275 2485 Fax 10x297) 1 c. ROVED 5-1 Yangcheong-ri, k, KOREA, 363-883 : +82 43 275 2487 Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 2 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS Revision Log This log identifies those portions of this document, which have been revised since the original issue and the date of each revision. Rev. Authorizing Document Summary of Changes to Previous Version Date Approval Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 3 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS Table of Contents Scope 4 Part Name Information 4 Composition and Materials 4 Mechanical Dimensions 5 Electrical Specifications 6 Test Fixture 6 S11 Measurement Data 7 Environmental Specifications 8 Radiation Patterns after Set Ass’y 9,10 Remark 11 Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 4 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS 1. Scope. This specification covers the characteristics of the quadrifilar meander antenna element for the ISM band. 2. Part Name Information. Part Name : M QMA 60S H 939 - A ⓛ ② ③ ④ ⑤ ⑥ ⓛ : MAC technologies Inc. ② : Quadrifilar Meander Antenna ③ : 60 mm Bottom substrate, 60 mm Top substrate, Square (Size) : ④9 mm Thickness (A : 2 mm, B : 3 mm, C : 4 mm ...) : ⑤Center Frequency : 939 MHz ⑥ : Assembly : cable 3. Composition and Materials. 3-1. Substrate : Keeping a secret from outsides 3-2. Metal Connector : Metal and teflon Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 5 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS 4. Mechanical Dimensions. (unit : mm) 4-1. Antenna Element [SIDE VIEW][BOTTOM VIEW][TOP VIEW] 9.0±0.3 MACINSIDE MQMA60S Feed Network MAC technologies Inc. (REV.0 2012.xxxx) 4-R2.0 60.0±0.2 60.0±0.260.0±0.2 4-R2.0 60.0±0.2 8.8 10.0±0.3 (Connector pins) 4-2. Cable Ass’y Unit : mm Ass'y Part Antenna Element After Ass'y 80 IPX Cable [SIDE VIEW][FRONT VIEW][SIDE VIEW] 10.0±0.3 (Connector pins) 11.0 MAX 4-R2.0 Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 6 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS 5. Electrical Specifications. NO. Parameter Spec. Unit Remark Cable Ass’y Set Ass’y 1 Center Frequency 939.0 ± 3 919.0 ± 3 MHz 2 Band Width min. 15 min. MHz @ -10 dB R.L 3 VSWR max. 2.0 : 1 max. Ratio 4 Impedance 50 Ohms 5 Peak Gain min. -1.5 min. dBiL @ 919 MHz Set Ass’y 6 Polarization RHCP 7 Beam Width typ. 105 typ. Deg. 6. Test Fixture. Styrofoam Jig IPX-80 mm Antenna Protek A333 NETWORK ANALYZER 300 kHz - 3.2 GHz Preset USB CONTROL ENTRY NAVIGATION Port 2 50 ? Port 1 50 ? Title Docume Revisio Issue D MACQM 7 7. 7-1. C 7-2. S ent Number n & Date ate 730-06 REV.0 S11 Me Cable Ass’y Set Ass’y RFID Qu MACQM7 0 May 04, 0 CERAMI easurem uarifilar Meande 730-06-12006 2012 MAC ICS ＆ RF COMPO ent Data er Ant. Specifica technologies ONENTS FOR TEL a. ation s Inc. ECOMMUNICATIO N SYSTEMS A4(21 10x297) 7 Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 8 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS 8. Environmental Specifications. ** Operation conditions : Temperature range : -30 °C ~ +85 °C Humidity range : 45 ~ 85 % RH The device should satisfy the electrical characteristics specified in paragraph 4 after the following tests. Measurements should be done after putting in the typical condition (20~30 °C / 55~75 % RH) for 2 hours minimum. 8-1. Temperature Characteristics The device should satisfy the electrical characteristics specified in paragraph 4 at the temperature range of –30 °C ~ +85 °C. 8-2. Heat Proof The device should satisfy the electrical characteristics specified in paragraph 4 after exposed to the temperature85 ± 2 °C for 72 hours. 8-3. Cold Proof The device should satisfy the electrical characteristics specified in paragraph 4 after exposed to the temperature –30 ± 2 °C for 72 hours. 8-4. Moisture Proof The device should satisfy the electrical characteristics specified in paragraph 4 after exposed to the temperature 40 ± 2 °C and the humidity 95 % RH for 72 hours. 8-5. Vibration The device should satisfy the electrical characteristics specified in paragraph 4 after applied to the vibration of 10 to 50 Hz with amplitude of 1.5 mm & sw of 1min for 2 hours each of x, y and z directions. Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date May 04, 2012 MACQM730-06 REV.0 MAC technologies Inc. A4(210x297) 9 CERAMICS ＆ RF COMPONENTS FOR TELECOMMUNICATION SYSTEMS 9. Radiation Patterns after Set Ass’y (Test date 2012.05.04) 9-1. H-pol (Frequency 917.0, 919.0, 921.0, 923.0 MHz) 9-2. V-pol (Frequency 917.0, 919.0, 921.0, 923.0 MHz) Title RFID Quarifilar Meander Ant. Specification Document Number MACQM730-06-12006 Revision & Date 0 Issue Date M…

Text truncated - open the document above for the full version.

Bluebird Soft Inc. 1242, Gaepo-dong, Gangnam-gu, Seoul, Korea Date: December 05, 2012 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

Bluebird Soft Inc. 1242, Gaepo-dong, Gangnam-gu, Seoul, Korea Date: December 05, 2012 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of DIGITAL EMC CO., LTD. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: SS4BIP6000MAXID including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of DIGITAL EMC CO., LTD. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Bluebird Soft Inc. Sincerely, Joo-Hyung Lee Director

Bluebird Soft Inc. 1242, Gaepo-dong, Gangnam-gu, Seoul, Korea Date: December 05, 2012 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: SS4BIP6000MAXID To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Bluebird Soft Inc. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Bluebird Soft Inc. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Operational Description 3 Schematics 4 Part Lists and Tune-Up Procedure SHORT-TERM 5 Internal Photos 6 Users Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Joo-Hyung Lee Director

Bluebird Soft Inc. 1242, Gaepo-dong, Gangnam-gu, Seoul, Korea Date: December 05, 2012 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA DECLARATION FOR ADDITIONAL FREQUENCY HOPPING REQUIREMENTS To whom it may concern: We hereby declare that the Bluetooth of SS4BIP6000MAXID meet following FCC requirements of the Section 15.247(a)(1) : 1. The hopping sequence is pseudorandom. 2. All channels are used equally on average. 3. The receiver input bandwidth approximately equal the transmit bandwidth. 4. The receiver hop in sequence with the transmit signal. Sincerely, Joo-Hyung Lee Director

FCCID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. View 1 FCCID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. View 2 FCCID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. View 3

FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase The label is attached to this device by an adhesive. The adhesive is permanent type with strong strength. Additionally, the label is readily to the purchaser at the time of purchase.

FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. View 1 FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. View 2 FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. View 3 FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, DIGITAL EMC Co., Ltd. RFID Antenna Minimum test separation distance for calculating SAR test exclusion threshold level

MHzmm = ± =[ / ]*[√ ] = [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW 50 Step 2-1) SAR test exclusion thresholds for 100MHz to 1500MHz at test separationn distances > 50 mm = N/A 4.86 ≤ 7.5, for 10g extrmity SAR Copyright Ⓒ 2013, Digital EMC Co., Ltd. Step 2-2) SAR test exclusion thresholds for 1500MHz to 6GHz at test separationn distances > 50 mm = N/A January 17, 2013 928 - Min. test separation distance = mW 23.61 24.00 dBm dB Typical Power:Measured Power: 23.00 dBm 1.00 dBm Please refer to internal photo for the distance. - Min. transmitting frequency = SS4BIP6000MAXID 252.00 0.928 50 - Max. power with turn-up tolerance = 252 Used Step 1) SAR test exclusion thresholds for 100MHz to 6GHz at te st separationn distances ≤ 50 mm = [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] FCC ID : Standalone SAR test exclusion considerations

FCC ID : SS4BIP6000MAXID DEMC1207-01217 Report No.: DRTFCC1212-0862 TRF-RF-212(00)101214 Page 2 / 30 Copyright ○ C 2012, Digital EMC Co., Ltd. Table of Contents 1. General Information ............................................................................................................... 4 1.1 Testing Laboratory ........................................................................................................ 4 1.2 Details of Applicant ....................................................................................................... 4 1.3 Support Equipment ....................................................................................................... 4 1.4 Description of EUT ........................................................................................................ 4 1.4. Declaration by the manufacturer ................................................................................... 4 1.6. Test Equipment List ........................................................................................................ 5 1.7. Summary of Test Results ................................................................................................ 6 1.8 Conclusion of worst-case and operation mode ............................................................ 7 1.9 Test report revision .......................................................................................................... 7 2. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission ............ 8 2.1. Test Setup ......................................................................................................................... 8 2.2. Limit .................................................................................................................................. 8 2.3. Test Procedures .............................................................................................................. 9 2.3.1. Test Procedures for Radiated Spurious Emissions ................................................ 9 2.3.2. Test Procedures for Conducted Spurious Emissions ............................................ 9 2.4. Test Results .................................................................................................................... 10 2.4.1. Radiated Emission .................................................................................................... 10 2.4.2. Conducted Spurious Emissions ............................................................................. 11 3. Carrier Frequency Separation ............................................................................................. 16 3.1. Test Setup .................................................................................................................... 16 3.2. Limit ................................................................................................................................ 16 4. Number of Hopping Frequencies ..................................................................................... 18 4.1. Test Setup .................................................................................................................... 18 4.2. Limit ................................................................................................................................ 18 5. 20dBc BW .............................................................................................................................. 20 5.1. Test Setup ....................................................................................................................... 20 5.2. Limit ................................................................................................................................ 20 5.3. Test Procedure .............................................................................................................. 20 5.4. Test Results .................................................................................................................... 20 6. Time of Occupancy (Dwell Time) ........................................................................................ 23 6.1. Test Setup ....................................................................................................................... 23 6.2. Limit ................................................................................................................................ 23 6.3. Test Procedure .............................................................................................................. 23 6.4. Test Results .................................................................................................................... 23 7. Maximum Peak Output Power Measurement .................................................................... 25 7.1. Test Setup ....................................................................................................................... 25 7.2. Limit ................................................................................................................................ 25 7.3. Test Procedure ............................................................................................................... 25 7.4. Test Results .................................................................................................................... 26 FCC ID : SS4BIP6000MAXID DEMC1207-01217 Report No.: DRTFCC1212-0862 TRF-RF-212(00)101214 Page 3 / 30 Copyright ○ C 2012, Digital EMC Co., Ltd. 8. Transmitter AC Power Line Conducted Emission ............................................................ 29 8.1. Test Setup ....................................................................................................................... 29 8.2. Limit ................................................................................................................................ 29 8.3. Test Procedures ...........................................…

Text truncated - open the document above for the full version.

FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 1 FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 2 FCC ID: SS4BIP6000MAXID Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 3