SSL2303BJoypad Game Controller

For FCC/CE Test Use PSII RF 2.4GHz Wireless Gamepad FCC/CE TEST Device (Controller)Test Mode Manipulate Manual 1. open for power switch (Power ON the Device/Controller). 2. Whether in common pulsatile frequency connect manipulate mode just the same pulsatile frequency transmit test mode under ，can pass to press the row combination key to set the new test mode Setup Different TEST MODE: u L3 + ×(Fork) into connect manipulate test mode u L3 + □(Square) into RF transmit test mode u L3 + L2 into RF receive test mode u L3 + LEFT into Sleep test mode Setup Different power estate: u L3 + ○(Circle) setup RF power for 0dB u L3 + △(Triangle) setup RF power for -5dB Setup channel : u L3 + UP setup RF channel fastness for Channel 78(2.480GHz) u L3 + RIGHT setup RF channel fastness for Channel 39(2.441Ghz) u L3 + DOWN setup RF channel fastness for Channel 0(2.402GHz) Setup motor estate: u L3 + L1 open for motor to maximal u L3 + R1 motor comeback natural estate Example 1: Under the condition of POWER switch on after the DEVICE AND HOST being placed in the connect, to want into -5dB, 78 channels transmit to test the mode, can carry out with the operation step of underneath Step 1: L3 + △ Step 2: L3 + UP Step 3: L3 + □ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Modifications not authorized by the manufacturer may void users authority to operate this device For FCC/CE Test Use

PAGE 1 OF 2 FACSIMILE To: MET Laboratories, Inc. Date: 2002-01-05 Attn. : Mr. Chris Harvey E-mail: [email protected] From: Alice Wong [EED Department] E-mail: [email protected] CC: Kitty Choy [EED Department] FCC ID: SSL2303B Subject : Apply One FCC Certificate NOT CONFIDENTIALITY Applicant: SHENZHEN HAIS ELECTRONICS CO., LTD Address: 14 Building, Chentian Industrial Zone, Baomin 2/R, Bao’an, Shenzhen, China. FRN: 0012-2815-64 Grantee Code: SSL FCC ID: SSL2303B Product: 2.4G Game Controller Model: HS-2303B If you have any question, please free feel to contact me. Please see attached sheet and following! For and on behalf of The Hong Kong Standards & Testing Centre Ltd.: Alice Wong EED Dept. Hong Kong Standards and Testing Centre 10 Dai Wang Street, Taipo Industrial Estate, NT, Hong Kong Tel : (852) 2666 1888 Fax : (852) 2665 0848 Email : [email protected] PAGE 2 OF 2 Item Description 1 Service agreement 2 Purchase Order 3 Letter of appointment 4 Letter of attestation 5 Circuit Description 6 Circuit diagram 7 Block diagram 8 PCB Layout 9 Parts List 10 User’s manual 11 FCC ID label 12 Label Location 13 Internal Photo 14 External Photo 15 Setup Photo 16 Report and Equipment list 17 Bandwidth Measuring Procedure: The procedure used was based on ANSI STANDARD C63.4-1992. The spectrum was scanned from 30MHz to 1000MHz. When an emission was found, the table was rotated to produce the maximum signal strength. The antenna was placed in both the horizontal and vertical planes and the worse case emissions were reported. The EUT was tested in vertical and cylindrical dimension, thus the orthogonal plane in X, Y and Z axis were covered.

21 03 05 Shenzhen Hais Electronic Co., Ltd. Shenzhen Hais Electronic Co., Ltd. 14 Building, Chentian Industrial Zone, Baomin 2/R Bao'an Shenzhen, China Shenzhen Hais Electronic Co., Ltd. 2005-03-21

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT

FCC ID: SSL2303B MADE IN CHINA This device complies with part 15 of the FCC Rules. Operat- ion is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, inclu- ding interference that may cause undesired operation.

PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT TOP VIEW INNER CIRCUIT BOTTOM VIEW

Field Strength of Fundamental Emission and Harmonics Emission Peak value Frequency MHz EMI Receiver Reading dBuV Antenna factor dB/m Cable Loss dB Preamplifier Gain dB Field Strength dBuV/m Field Strength uV/m Limit @ 3meter E-Field polarity 2310-2390 28.6 30.1 3.8 33.8 28.7 27.22 500 H/V 2483.5-2500 29.2 30.3 3.8 33.5 29.8 30.90 500 H/V Field Strengh (dBuV/m) =EMI receiver reading (dBμV) + Antenna factor(dB/m) + cable Loss (dB) – Preamplifier gain(dB) Limit is based on Average value * Denotes restricted band of operation. Measurements were made using a peak detector. Any emission less than 1000 MHz and falling within the restricted bands of FCC Rules Part 15 Section 15.205 and the limit of FCC Rules Part 15 Section 15.209 were applied

NO DescriptionSpecificationQty Place 1 SMD Resistor 10Ω ±5%,0805 2R4,R7 2 SMD Resistor 1KΩ ±5%,0805 2R2-3, 3 SMD Resistor 2.7KΩ ±5%,0805 17R1,R5-6,R16-28,R45 4 SMD Resistor 3.9KΩ ±5%,0805 4 R8-10，R36 5 SMD Resistor 10KΩ ±5%,0805 6R42,R11-15 6 SMD Resistor 20KΩ ±5%,1206 1R39 7 SMD Resistor 39KΩ ±5%,0805 1R33 8 SMD Resistor 100KΩ ±5%,0805 1R30 9SMD Capacitor 22P ±10%,0805 2C4-5 10SMD Capacitor 100P ±5%,0805 3C10-11,C13 11SMD Capacitor 103P ±5%,0805 1C7 12SMD Capacitor 104P ±10%,0805 7C3,C8-9,C14,CC1-3, 13SMD DIODEIN4148/12062D1-2 14SMT ICHT75331U2 15SMT TransistorSOT-23 80503 Q1，Q2，Q21 16SMT TransistorSOT-23 9012/855014 Q3-15，Q18 17 IC SN8P17O7(MAS-3401-01) 1 U1 1MOTOR φ24.4＊12.5mm，3V,Wheel 12*4.8mm 1 M1 2MOTOR φ24.4＊12.5mm，3V,Wheel 18*6mm 1 M2 3 3D Variable Resistors B10K 2 L3，R3 4 PCB1 2303-01-13 132*47*1.2mm,R=19K OHM 1 5 PCB2 2303-02-13 85*28*1.2mm 1 3D VR PCB 6 PCB3 2303-03-13 17*6.7*1.2mm 1 SW PCB 7 PCB4 2303-04-13 18*28*1.2mm R=19KOHM 2 L,R SMALL PCB 8E.Capacitance4.7UF/16V 4*7mm±10%1C6 9 E.Capacitance 47UF/16V 5*7mm±20%1C2 10 E.Capacitance 100UF/16V 7*7mm±20%1C1 11CRYSTAL:12MHZ" h=3.5mm 1Y1 12 1PIN Lead the line BLACK,L=60mm 1SW PCB 138PIN Lead the line L=34+3+3mm 1 BIG PCB 143PIN WHITE Lead the line L=24+3+3mm 2CON5,CON4 15LEDOrange 2X5X7mm1ANA 16LEDgreen 2X5X7mm1MARCO 17+/"-"The battery plays slice2+1 18"+"The battery plays slice8.5*10MM1 19"-"The battery plays slice8.5*10MM1 201P1T SwitchG51POWER SW 21 12PIN 0.5*0.5*9mm Socket L=2.0 MM 1 RFMODUL PCB 222PIN Lead the line 75+4+4mm，L=2.0mm， 1 Connect POWER 23 RFMODUL REV:320*30*1.6mm 1 1 1,Rubber key E179 (4PCSKEY)1 Direction KEY 2 2,Rubber key E182 (3+1KEY) 1 Inside key 3 3,Rubber key E131B (4PCSKEY)1R KEY 4 4,Rubber key ZH-0064 2R1,L1 key RF2.4G PS2 JOY PAD B.O.M HS2303B configuration part: Electronics part weld part 5 5,Rubber key E104 4 R2，L2,TURBO， SLOW key 6 top Hull 1 7 Bottom hull 1 8Left adornment plank 1 9Right adornment plank 1 10Direction KEY 1 11 Left/Right 1& 2 key 4 R1，R2，L1，L2 12TURBO，SLOW key2 13 LOGO,Slice 1 14 X△□○ key 4 15 EVA Sponge Only with dauby 8*8*5.5MM2MOTOR 16 EVA Sponge Only with dauby 12*12*5MM 1 RFMODUL 17Mushroom pole BLACK 2 18screw PA2.3*8mm 7 19 screw PWA2.3*8mm 4 PCB 20 screw PA2.0*6mm 2 sw PCB

1 2 3 4 56 ABCD 6 5 4 3 2 1 D CBA Title Number Revision Size B Date: 6-Dec-2004 Sheet of File: D:\lzh\ddb\88.ddb Drawn By: VCC K2Right K3Up K4 Left K1Down K5R1 K6R2 K7L2 K8L1 R93.9K K12BD K11BR K10BU K9BL R10 3.9K Q158550 VCC A -+ LM Q18050 Vbat R410 R52.7K D14148 C9104 A -+ RM Q28050 R710 R62.7K D24148 C14104 Vbat C7 103 VPPD0D1D2D3D4D5D6D7 VCC CECLKOEPGMRST Please stay a test order to used for burning to record VPP Y112M C522P C4 22P CLK C64.7uF R12.7K VCC CE D0D1D2D3 PGM OE VCC R12 10K R13 10K R11 10K LED1 macro R2 1K K15L3 K16 SELECT K17R3 K18 START CC2104 C11100p C13 100p RST R1510K R1410K R83.9K C10100p Q38550 Q48550 Q58550 Q68550 Q78550 Q88550 Q98550 Q108550 VCC VCC VCC VCC VCC VCC VCC VCC Q118550 Q128550 Q138550 Q148550 VCC VCC VCC VCC K14 macro VCC R16 2.7K R172.7K R182.7K R192.7K R28 2.7K R202.7K R212.7K R222.7K R232.7K R242.7K R252.7K R262.7K R272.7K RY B10K RXB10K LY B10K LXB10K 1 VPP 2 P0.0/INT0 3 P0.1/INT1 4 P0.2/INT2 5 RST 6 P1.5 7 P1.4 8 P1.3 9 VDD 10 P1.2 11 P1.1 12 P1.0 13 P2.0 14 P2.1 15 P2.2 16 P2.3 17 VSS 18 AVSS 19 P4.7/AIN7 20 P4.6/AIN6 21 P4.5/AIN5 22 P4.4/AIN4 23 P4.3/AIN3 24 P4.2/AIN2 25 P4.1/AIN1 26 P4.0/AIN0 27 AVREF 28 VDD/AVDD 29 DAO 30 P5.7 31 P5.6 32 P5.5 33 P5.4/TC0/PWM0 34 P5.3/TC1/PWM1 35 P5.2/SO 36 P5.1/SI 37 P5.0/SCK 38 P2.4 39 P2.5 40 P2.6 41 P2.7 42 VSS 43 XOUT 44 XIN U1SN8P17O7(MAS-3401-01) VCC D4 D5 D6 D7 ADC_VREF ADC_VREF Up-GND Right-VDD DATA 2 CLK1 3 DR1 4 CS 5 DOUT2 6 CLK2 7 DR2 8 CE 9 PWR_UP 10 VDD 11 GND 12 GND 1 J1RF NRF2401_PORT VCC Connect RF Module K19Turbo K20 CLEAR LEFT_MOTOR LEFT_MOTOR R4210K VCC C3104P GND 1 VIN 2 VOUT 3 U2HT7533 P1-vccBattery C1100uF CC1104 C247uF VCC Vbat 1.5V*4 sw1Power switch Q18S9012 R363.9K R3920K R3339K K13mode LED2 mode R3 1K Q21S8050 R30100K R452.7K LVD_C LVD_C LowVvoltage Detect 2303B.sch( PS2 RF JOY PAD) BT1/2aaa1.5v*2 Bt3/4 aaa1.5v*2 VCC CC3104 L3D R3D 1234567891011121314151617181920

香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 1 of 19 No. : HM151412 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Applicant: SHENZHEN HAIS ELECTRONICS CO., LTD 14 Building, Chentian Industrial Zone, Baomin 2/R, Bao’an, Shenzhen, China Description of Samples: Model name: 2.4G Game Controller Model no.: HS-2303B Brand name: N/A FCC ID: SSL2303B Date Samples Received: 2004-06-08 Date Tested: 2004-07-02 to 2004-11-18 Investigation Requested: FCC Part 15 Regulations-Subpart C Conclusions: The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remarks: ---- K C Lee, EMC for Chief Executive 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 2 of 19 No. : HM151412 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). CONTENT: Cover Page 1 of 18 Content Page 2-3 of 18 1.0 General Details 1.1 Test Laboratory Page 4 of 19 1.2 Applicant Details Page 4 of 19 Applicant HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 19 Description of EUT operation 1.4 Date of Order Page 5 of 19 1.5 Submitted Sample Page 5 of 19 1.6 Test Duration Page 5 of 19 1.7 Country of Origin Page 5 of 19 1.8 Additional Information of EUT Page 6 of 19 2.0 Technical Details 2.1 Investigations Requested Page 7 of 19 2.2 Test Standards and Results Summary Page 7 of 19 3.0 Test Results 3.1 Radiated Emission Page 8-13 of 19 3.2 Conducted Emission Page 14 of 19 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 3 of 19 No. : HM151412 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Appendix A List of Measurement Equipment Page 15 of 19 Appendix B Duty Cycle Correction During 100 msec Page 16-17 of 19 Appendix D Photographs Page 18-19 of 19 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 4 of 19 No. : HM151412 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong 1.2 Applicant Details Applicant SHENZHEN HAIS ELECTRONIC CO., LTD 14 Building, Chentian Industrial Zone, Baomin 2/R, Bao’an, Shenzhen, China HKSTC Code Number for Applicant SZH001 Manufacturer SHENZHEN HAIS ELECTRONIC CO., LTD 14 Building, Chentian Industrial Zone, Baomin 2/R, Bao’an, Shenzhen, China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 5 of 19 No. : HM151412 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.3 Equipment Under Test [EUT] Description of Sample Product: 2.4G Game Controller Manufacturer: Shenzhen Hais Electronic Co., Ltd. Brand Name: N/A Model Number: HS-2303B Input Voltage: 6Vd.c. (“AAA” size battery x 4) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is a 2.4G Game Controller, the transmission signal is frequency hopping with channel frequency range 2.402-2.480 GHz. 1.4 Date of Order 2004-06-08 1.5 Submitted Sample(s): 10 Samples per model 1.6 Test Duration 2004-07-02 to 2004-11-18 1.7 Country of Origin China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 6 of 19 No. : HM151412 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2005-03-04 TEST REPORT Page 7 of 19 No. : HM151412 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 2.0 Technical Details 2.1 Investigations Requested Pe…

Text truncated - open the document above for the full version.

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP