SSVNAEPI01Oven with wireless food probe system

Integration manual for the wireless roast probe system 1 General This document describes the requirements for the oven when installing the wireless roast probe system. The wireless roast probe system consists of the electronic (EPI7674), antenna system and the wireless roast probe. The wireless roast probe will be here not describe because it is a passive device and does not matter for the installation of the system. The wireless roast probe system may only be installed due to the identical antenna system in the Miele & Cie. KG ovens with 36 inch, 30 inch und 70 cm cooking cavity. The certified Module, see picture below, will only be installed by Grantee Miele. Picture 1: label of the module 2 Electronic EPI7674: 2.1 Position of the EPI7674 on the control-/ power electronic of the oven Picture 2: Position of the EPI  Fixing of the EPI7674 carried out by latching the housing of the control-/ power electronic with a spacer. For better alignment during assembly, a round plastic dome of the control- / power electronic is next to the connector tor the antenna cable.  The distance between two electronics is ensured by the housing of the control-/ power electronic and is approximately 7 mm. 2.2 Interface to the control-/ power electronic On the control-/ power electronic is a six pin stripe with the following pin assignment On the EPI is a female connector for the contact with the interface. The power supply (3.3 V DC +/-5 %) for the EPI comes from constant-voltage source of the control electronic. 2.3 Antenna conector Jack straight PCB MCX 50 Ohm. 3 Antenna system The antenna system includes the rod antenna with the coupling plate and the rear wall of the oven. The rear wall is capacitive coupled to the rod antenna. All together generates the electric field in the cavity and a certain directivity of the radiation. Picture 3: rod antenna with the coupling plate, mcx-connector Picture 4: rod antenna with the coupling plate insalled in the cavity Picture 5: rear wall coupled to the rod antenna 4 Manual Statements The manual or instruction manual should include the following statements in English and France:  changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  This oven complies with Industry Canada licence-exempt RSS standard(s) and part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5 Label The FCC an IC identifier must be displayed on the device label in this way: contains: FCC-ID: SSVNAEPI01 ; IC: 5669B-NAEPI01

PHOENIXTESTLABGmbH ProductCertificationDepartment Königswinkel10 D 32825Blomberg To WhomIt MayConcern: Pleasebe advisedthatwe,Miele& Cie.KG,authorizethe followingpeoplefromPHOENIX TESTLABGmbH: • Mr. JulioLopez • Mr. UweDollitz • Ms.Chvi-ChenChai to handlethe applicationof TypeApprovalServicesincludingin-country-testingin the followingcountries: USA Canada PHOENIXTESTLABGmbHhasour permissionto useour technicaldocumentsfor the approvals. Unlessyoureceivefuturecorrespondencefromus, pleaseextendyourfull cooperationto PHOENIXTESTLABGmbHregardingmattersrelatingto the abovementionedproducts within24 monthsafterthe signatorydateof thisauthorization. Contactperson Positionin the company Dateof signatory Mr. WinfriedLuthe DirectorProductEngineering& Development 2014-03-26 Signatory (Signatureof the applicant)

Ersteller: D. Brandhorst Revision: 00 Erstelldatum: 02.01.2012 Datum: 00.00.0000 Seite 1 von 1 Long/Short-term Confidentiality Request PHOENIX TESTLAB GmbH Date: 04 August 2014 Product Certification Königswinkel 10 D 32825 Blomberg FCC ID: SSVNAEPI01 To Whom it may concerns, Pursuant to sections 0.457(d) and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, we hereby requests long-term confidential treatment of information accompanying this application as outlined below: Schematics Parts List Block Diagram Tune-Up Info Operational Description In addition we hereby request the following exhibits contained in this application to be temporarily (short-term confidentilality) withheld from the public disclosure for an initial period of days until: not applicable External Photos Test Setup Photos Internal Photos Users Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to rule 0.457(d), disclosure of this application and all accompanying documentation will not be made before the date of the GRANT for this application. Thank you for your attention in this matter. Signing Party : Signature : Name / Position : Uwe Dollitz Graduated Certification Specialist

Attn: Reviewing Engineer RE: PART 15 UNLICENSED LIMITED MODULAR TRANSMITTER APPROVAL To Whom It May Concern: We, Phoenix Testlab, hereby requests, in the name of Miele, for part 15 unlicensed limited modular transmitter approval of our device, described as follows: FCC ID: SSVNAEPI01 In FCC Public Notice DA 00-1407 released June 26,2000 there are eight numbered requirements that our device complies with: 1. The modular transmitter does not have its own shielding. The module is only installed by the Grantee Miele. 2. The modular transmitter includes buffered modulation/data inputs in IC PIC24FJXXGA002 3. The modular transmitter does not have its own power supply regulation and the module is limited to 3.3 V DC +/- 5%. The module is only installed by the Grantee Miele. 4. The modular transmitter complies with the antenna requirements of Section 15.203 and 15.204c. The antenna is builded directly into the oven 5. The modular transmitter was tested inside different ovens as documented in the filing 6. The modular transmitter is labelled with its own FCC ID number, refer to the integration manual 7. The modular transmitter complies with the specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. 8. The modular transmitter is exempted from the applicable RF exposure requirements. Name / Position : Uwe Dollitz Graduated Certification Specialist

ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 1 of 4 132604_1_a.JPG: H6780BP, 3-D-view 1 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 2 of 4 132604_1_e.JPG: H6780BP, 3-D.view 2 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 3 of 4 132604_1_n.JPG: H6780BP, cooking chamber (door opened) ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 4 of 4 132604_1_t.JPG: H6780BP, type plate

ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 1 of 4 132604_2_m.JPG: H6880BP, 3-D-view 1 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 2 of 4 132604_2_a.JPG: H6880BP, 3-D.view 2 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 3 of 4 132604_2_l.JPG: H6880BP, cooking chamber (door opened) ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 4 of 4 132604_2_r.JPG: H6880BP, type plate

ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 1 of 4 132604_3_a.JPG: H6780BP2, 3-D-view 1 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 2 of 4 132604_3_b.JPG: H6780BP2, 3-D.view 2 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 3 of 4 132604_3_c.JPG: H6780BP2, cooking chamber (door opened) ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 4 of 4 132604_3_h.JPG: H6780BP2, type plate

ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 1 of 4 136015_1_c.JPG: HR1622, 3-D-view 1 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 2 of 4 136015_1_e.JPG: HR1622, 3-D.view 2 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 3 of 4 136015_1_b.JPG: HR1622, cooking chamber (door opened) ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 4 of 4 136015_1_f.JPG: HR1622, type plate view

ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 1 of 3 136015_2_m.JPG: HR1934, 3-D-view 1 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 2 of 3 136015_2_n.JPG: HR1934, 3-D.view 2 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 3 of 3 136015_2_o.JPG: HR1934, cooking chamber (door opened)

ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 1 of 3 136015_3_k.JPG: HR1954, 3-D-view 1 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 2 of 3 136015_3_l.JPG: HR1954, 3-D.view 2 ANNEX B: EXTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 3 of 3 136015_3_m.JPG: HR1954, cooking chamber (door opened)

ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 1 of 7 132604_1_f.JPG: EPI7674 inside H6780BP, internal view 1 (cover removed) ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 2 of 7 132604_1_k.JPG: EPI7674 inside H6780BP, internal view to main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 3 of 7 132604_1_m.JPG: EPI7674 inside H6780BP, internal view to rf PCB on main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 4 of 7 132604_1_q.JPG: EPI7674 bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 5 of 7 132604_1_s.JPG: EPI7674 bottom view, type plate removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 6 of 7 132604_1_r.JPG: EPI7674 top view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 7 of 7 132604_1_p.JPG: EPI7674 inside H6780BP, antenna view

ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 1 of 7 132604_2_d.JPG: EPI7674 inside H6880BP, internal view 1 (cover removed) ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 2 of 7 132604_2_e.JPG: EPI7674 inside H6880BP, internal view to main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 3 of 7 132604_2_i.JPG: EPI7674 inside H6880BP, internal view to rf PCB on main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 4 of 7 132604_2_o.JPG: EPI7674 bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 5 of 7 132604_2_p.JPG: EPI7674 bottom view, type plate removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 6 of 7 132604_2_q.JPG: EPI7674 top view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 7 of 7 132604_2_k.JPG: EPI7674 inside H6880BP, antenna view

ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 1 of 7 132604_3_e.JPG: EPI7674 inside H6780BP2, internal view 1 (cover removed) ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 2 of 7 132604_3_f.JPG: EPI7674 inside H6780BP2, internal view to main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 3 of 7 132604_3_g.JPG: EPI7674 inside H6780BP2, internal view to rf PCB on main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 4 of 7 132604_3_j.JPG: EPI7674 bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 5 of 7 132604_3_k.JPG: EPI7674 bottom view, type plate removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 6 of 7 132604_3_i.JPG: EPI7674 top view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F132604E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-112604 page 7 of 7 132604_3_d.JPG: EPI7674 inside H6780BP2, antenna view

ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 1 of 6 136015_1_k.JPG: EPI7674 inside HR1622, internal view 1 (cover removed) ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 2 of 6 136015_1_j.JPG: EPI7674 inside HR1622, internal view to main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 3 of 6 136015_1_m.JPG: EPI7674 bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 4 of 6 136015_1_n.JPG: EPI7674 bottom view, type plate removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 5 of 6 136015_1_l.JPG: EPI7674 top view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E1, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 6 of 6 136015_1_i.JPG: EPI7674 inside HR1622, antenna view

ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 1 of 7 136015_2_i.JPG: EPI7674 inside HR1934, internal view 1 (cover removed) ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 2 of 7 136015_2_h.JPG: EPI7674 inside HR1934, internal view to main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 3 of 7 136015_2_c.JPG: EPI7674 bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 4 of 7 136015_2_d.JPG: EPI7674 bottom view, type plate removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 5 of 7 136015_2_b.JPG: EPI7674 top view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 6 of 7 136015_2_a.JPG: EPI7674 inside HR1934, antenna view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E2, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 7 of 7 136015_2_l.JPG: HR1934, type plate

ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 1 of 7 136015_3_g.JPG: EPI7674 inside HR1954, internal view 1 (cover removed) ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 2 of 7 136015_3_h.JPG: EPI7674 inside HR1954, internal view to main PCB ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 3 of 7 136015_3_b.JPG: EPI7674 bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 4 of 7 136015_3_f.JPG: EPI7674 bottom view, type plate removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 5 of 7 136015_3_e.JPG: EPI7674 top view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 6 of 7 136015_3_a.JPG: EPI7674 inside HR1954, antenna view ANNEX C: INTERNAL PHOTOGRAPHS Examiner: Thomas KÜHN Test Report No.: F136015E3, 2 nd version Date of issue: 23 May 2014 Order No.: 13-116015 page 7 of 7 136015_3_j.JPG: HR1954, type plate

Königswinkel 10 32825 Blomberg Germany Phone: +49 (0) 52 35 95 00-0 Fax: +49 (0) 52 35 95 00-10 Test Report Report Number: F132604E1, 2 nd version Applicant: Miele & Cie. KG Werk Oelde Manufacturer: Miele & Cie. KG Werk Oelde Equipment under Test (EUT): H6780BP with EPI7674 inside Laboratory (CAB) accredited by Deutsche Akkreditierungsstelle GmbH (DAkkS) in compliance with DIN EN ISO/IEC 17025 under the Reg. No. D-PL-17186-01-02, FCC Test site registration number 90877 and Industry Canada Test site registration IC3469A-1 Test engineer: Thomas KÜHN Report Number: F132604E1, 2 nd version Date of issue: 23 May 2014 Order Number: 13-112604 page 2 of 40 REFERENCES [1] ANSI C63.4-2009 American National Standard for Methods of Measuring of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. [2] FCC CFR 47 Part 15 (August 2013) Radio Frequency Devices [3] RSS-210 Issue 8 (December 2010) Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment [4] RSS-Gen Issue 3 (December 2010) General Requirements and Information for the Certification of Radio Apparatus TEST RESULT The requirements of the tests performed as shown in the overview (clause 4) were fulfilled by the equipment under test. The complete test results are presented in the following. RESERVATION This test report is only valid in its original form. Any reproduction of its contents in extracts without written permission of the accredited test laboratory PHOENIX TESTLAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TESTLAB GmbH is not responsible for any generalizations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report. Each page necessarily contains the PHOENIX TESTLAB Logo and the TEST REPORT NUMBER. Test engineer: Thomas KÜHN 23 May 2014 Name Signature Date Authorized reviewer: Bernd STEINER 23 May 2014 Name Signature Date Test engineer: Thomas KÜHN Report Number: F132604E1, 2 nd version Date of issue: 23 May 2014 Order Number: 13-112604 page 3 of 40 Contents: Page 1 Identification ........................................................................................................................... 4 1.1 Applicant ............................................................................................................................ 4 1.2 Manufacturer ..................................................................................................................... 4 1.3 Test laboratory ................................................................................................................... 4 1.4 EUT (Equipment Under Test) ............................................................................................ 5 1.5 Technical data of equipment .............................................................................................. 5 1.6 Dates ................................................................................................................................. 6 2 Operational states .................................................................................................................. 6 3 Additional information ............................................................................................................. 7 4 Overview ................................................................................................................................ 7 5 Test results ............................................................................................................................ 8 5.1 Calculation of the measurement results ............................................................................. 8 5.2 20 dB bandwidth .............................................................................................................. 11 5.2.1 Method of measurement (20 dB bandwidth) ........................................................... 11 5.2.2 Test results (20 dB bandwidth) ............................................................................... 12 5.3 Radiated emissions ......................................................................................................... 14 5.3.1 Method of measurement (Radiated emissions) ....................................................... 14 5.3.2 Test results (radiated emissions) ............................................................................ 21 5.3.2.1 Preliminary radiated emission measurement ...................................................... 21 5.3.2.2 Final radiated emission measurement (30 MHz to 1 GHz) ................................. 30 5.3.2.3 Final radiated emission measurement (1 GHz to 5 GHz).................................... 33 5.4 Conducted emissions on power supply lines (150 kHz to 30 MHz) .................................. 34 5.4.1 Method of measurement ......................................................................................... 34 5.4.2 Test results (conducted emissions on power supply lines) ...................................... 35 6 Test equipment and ancillaries used for tests ....................................................................... 39 7 Report history ....................................................................................................................... 40 8 List of annexes ..................................................................................................................... 40 Test engineer: Thomas KÜHN Report Number: F132604E1, 2 nd version Date of issue: 23 May 2014 Order Number: 13-112604 page 4 of 40 1 Identification 1.1 Applicant Name: Miele & Cie. KG Werk Oelde Address: Carl-Miele-Platz 1 59302 Oelde Country: Germany Name for contact purposes: Mr. Andreas FABRIZIUS Phone: +49 52 45 91 – 74 615 Fax: +49 52 45 91 – 78 46 15 eMail Address: [email protected] Applicant repre…

Text truncated - open the document above for the full version.

Königswinkel 10 32825 Blomberg Germany Phone: +49 (0) 52 35 95 00-0 Fax: +49 (0) 52 35 95 00-10 Test Report Report Number: F132604E2, 2 nd version Applicant: Miele & Cie. KG Werk Oelde Manufacturer: Miele & Cie. KG Werk Oelde Equipment under Test (EUT): H6880BP with EPI7674 inside Laboratory (CAB) accredited by Deutsche Akkreditierungsstelle GmbH (DAkkS) in compliance with DIN EN ISO/IEC 17025 under the Reg. No. D-PL-17186-01-02, FCC Test site registration number 90877 and Industry Canada Test site registration IC3469A-1 Test engineer: Thomas KÜHN Report Number: F132604E2, 2 nd version Date of issue: 23 May 2014 Order Number: 13-112604 page 2 of 40 REFERENCES [1] ANSI C63.4-2009 American National Standard for Methods of Measuring of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. [2] FCC CFR 47 Part 15 (August 2013) Radio Frequency Devices [3] RSS-210 Issue 8 (December 2010) Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment [4] RSS-Gen Issue 3 (December 2010) General Requirements and Information for the Certification of Radio Apparatus TEST RESULT The requirements of the tests performed as shown in the overview (clause 4) were fulfilled by the equipment under test. The complete test results are presented in the following. RESERVATION This test report is only valid in its original form. Any reproduction of its contents in extracts without written permission of the accredited test laboratory PHOENIX TESTLAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TESTLAB GmbH is not responsible for any generalizations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report. Each page necessarily contains the PHOENIX TESTLAB Logo and the TEST REPORT NUMBER. Test engineer: Thomas KÜHN 23 May 2014 Name Signature Date Authorized reviewer: Bernd STEINER 23 May 2014 Name Signature Date Test engineer: Thomas KÜHN Report Number: F132604E2, 2 nd version Date of issue: 23 May 2014 Order Number: 13-112604 page 3 of 40 Contents: Page 1 Identification ........................................................................................................................... 4 1.1 Applicant ............................................................................................................................ 4 1.2 Manufacturer ..................................................................................................................... 4 1.3 Test laboratory ................................................................................................................... 4 1.4 EUT (Equipment Under Test) ............................................................................................ 5 1.5 Technical data of equipment .............................................................................................. 5 1.6 Dates ................................................................................................................................. 6 2 Operational states .................................................................................................................. 6 3 Additional information ............................................................................................................. 7 4 Overview ................................................................................................................................ 7 5 Test results ............................................................................................................................ 8 5.1 Calculation of the measurement results ............................................................................. 8 5.2 20 dB bandwidth .............................................................................................................. 11 5.2.1 Method of measurement (20 dB bandwidth) ........................................................... 11 5.2.2 Test results (20 dB bandwidth) ............................................................................... 12 5.3 Radiated emissions ......................................................................................................... 14 5.3.1 Method of measurement (Radiated emissions) ....................................................... 14 5.3.2 Test results (radiated emissions) ............................................................................ 21 5.3.2.1 Preliminary radiated emission measurement ...................................................... 21 5.3.2.2 Final radiated emission measurement (30 MHz to 1 GHz) ................................. 30 5.3.2.3 …

Text truncated - open the document above for the full version.