ST2-IT712ESingle-Use Patient Tag IT-712E/IT-709E/IT-722E

© CenTrak 2014. All Rights Reserved. Proprietary and Confidential. Case length1.5 in (39.5 mm) Case width1.2 in (31 mm) Case height (thickness)0.3 in (8.5 mm) Case weight (with battery) 0.42 oz (12 g) IT‐712 Mini Asset Tag •Small size, lightweight •Integrates with CenTrak’s RTLS and Guardian Security Solutions •Gen2IR™ Technology for Clinical‐Grade Locating™ applications •LF enabled to support choke point and egress detection •Internal tamper sensor to send alerts when tag is removed •Fully waterproof for easier cleaning •Battery access while attached to asset The tag is fully waterproof to allow for easy cleaning of all assets with the operation of other hospital or personal medical equipment. It is also resistant to soiling and UV light, and may be cleaned with a disinfectant solution. With a remarkably small profile, the tag is ideal for all medical equipment –partic ularly smaller assets like scopes and today’s more compact equipment. The tag communicates with CenTrak’s Guardian Security System as well as CenTrak’s Clinical‐Grade RTLS™, so facilities are able to continually monitor assets locations to optimize workflow and utilization, as well as prevent shrinkage. IT‐712 Mini Asset Tag CenTrak, Inc. 125 Pheasant Run Newtown, PA 18940 t: 215‐860‐2928 e: [email protected] www.centrak.com IT‐712 in use Specifications FCC/IC Operating Frequency Range902‐928 MHz (Model #IT‐712E) CE Average transmission power2 uW (average) Gen2IR SensorYES Low Frequency Sensor (125 KHz) RX Operating Temperature0 C to +50 C Sealingwaterproof This component complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) The device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Modifying or tampering with the transceiver’s or receiver’s internal component s can cause a malfunction, inva lidate th e warranty, and will void FCC authorization to use these products. This product or its systems are covered by one or more of the following U.S. patents: 5,917,425, 7,061,428, 7,378,964, 7,619,532. L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillageet (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The CenTrak Mini Asset Tag is a radio transmitter contained in a small, waterproof casing. The tag incorporates a tamper detection mechanism enabled as soon as the tag is applied to an asset. From this time forward, the tag is constantly monitored by the system. The Mini Tag features CenTrak’s Second Generation Infrared technology (Gen2IR™) and Low Frequency technology to support Clinical‐Grade Locating™ applications. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Date: December 15, 2014 FCC and IC Confidentiality Request In accordance with 0.459 & 0.457 of CFR 47, please, accept this letter as an official request to have the following kept as confidential for the reference IDs: IC: 6012A-IT712E Model numbers: IT-712E, IT-709E and IT-722E And: FCC: ST2-IT712E The information provided is for the sole purpose of inclusion as exhibits in the Application for Certificate of the FCC & IC IDs stated above: We ask to keep confidential the following Tag (model# IT-712E) documents:  Schematics and Parts List  Block Diagram  Operational description Sincerely, Israel Amir, CTO CenTrak, Inc. 5 Caufield Place, suite 102 Newtown, PA 18940 215.860.2928

Date: 5/27/2014 To whom it may concern: We, the undersigned, hereby authorize Wei Li, Advanced Compliance Labo ratory, Inc., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Advanced Compliance Laboratory, Inc. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are no t subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). I n authorizing Advanced Compliance Laboratory, Inc. as our agent, we still recognize that we are responsibl e to: • comply with the relevant provisions of the certification program; • make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; • make claims regarding certification only in respect of the scope for which certification has been granted; • do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; • upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; use certification only to indicate the products are certified as being in conformity with specified standards; • endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; • ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; • keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; • take appropriate action with respect to such complaints and any deficiencies found in products or se rvices that affect compliance with the requirements for certification; 5 Caufield Place Ste 102, Newtown PA 189 40 i Tel 215.860.2928 i Fax 215.359.0659 i www.centrak.com • document the actions taken This authorization is valid until further written notice from the a pplicant. Sincerely Yours, Printed Name: Israel Amir Title: CTO Company: CenTrak, Inc. z Page 2

EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 22 7.1 Front View EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 23 7.2 Back View

EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 8 2. PRODUCT LABELING Figure 2.1 FCC ID Label Figure 2.2 Location of Label on the Side of EUT Centrak MINI ASSET TAG Model No.: IT-712E /IT-709E/IT-722E FCC ID: ST2-IT712E IC: 6012A-IT712E This device complies with part 15 of the FCC Rules and IC RSS-210 & RSS-Gen Rules.. Operating is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Figure 2.2 Location of the Label ID Label Figuare 2.1 FCC/IC ID Label (Only ID show on the EUT)

EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 24 7.3 PCB Component Side View EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 25 7.4 PCB Foil Side View: with & without battery holder

ELECTROMAGNETIC EMISSION COMPLIANCE REPORT of MINI ASSET TAG MODEL: IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E IC:6012A-IT712E Dec. 17, 2014 This report concerns (check one): Original grant x Class II change Equipment type: Low Power Intentional Radiator Test Specifications: ____FCC Part 15C Sec. 15.249 ____Industry Canada RSS-210 (Issue 8) & RSS-Gen (Issue 3) Deferred grant requested per 47 CF 0.457(d)(1)(ii)? yes no x If yes, defer until: (date) Company agrees to notify the Commission by (date) of the intended date of announcement of the product so that the grant can be issued on that date. Report prepared for: CENTRAK, INC. Report prepared by: Advanced Compliance Lab Report number: 0048-141121-01 Lab Code: 200101 The test result in this report IS supported and covered by the NVLAP accreditation 6 Randolph Way Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 Advanced Compliance Laboratory EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 2 Table of Contents Report Cover Page .................................................................................................... 1 Table of Contents ...................................................................................................... 2 Figures ....................................................................................................................... 3 1. GENERAL INFORMATION .................................................................................. 4 1.1 Verification of Compliance ......................................................................... 4 1.2 Equipment Modifications ............................................................................ 5 1.3 Product Information ................................................................................... 6 1.4 Test Methodology ...................................................................................... 6 1.5 Test Facility ............................................................................................... 6 1.6 Test Equipment .......................................................................................... 6 1.7 Statement for the Document Use ................................................................ 7 2. PRODUCT LABELING .......................................................................................... 8 3. SYSTEM TEST CONFIGURATION ...................................................................... 9 3.1 Justification ................................................................................................ 9 3.2 Special Accessories .................................................................................... 9 3.3 Configuration of Tested System.................................................................. 9 4. SYSTEM SCHEMATICS ....................................................................................... 13 5. RADIATED EMISSION DATA ............................................................................. 14 5.1 Field Strength Calculation .......................................................................... 14 5.2 Test Methods and Conditions ..................................................................... 14 5.3 Test Data ................................................................................................... 14 6. EUT RECEIVING MODE VERIFICATION .......................................................... 20 7. PHOTOS OF TESTED EUT ................................................................................... 22 EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 3 Figures Figure 2.1 FCC/IC ID Label ..................................................................................... 8 Figure 2.2 Location of Label ..................................................................................... 8 Figure 3.1 Radiated Test Setup ................................................................................. 10 Figure 4.1 EUT Schematics ....................................................................................... 12 Figure 7.1 Front View ............................................................................................... 21 Figure 7.2 Back View ................................................................................................ 22 Figure 7.3 PCB Component Side View ..................................................................... 24 Figure 7.4 PCB Foil Side View .................................................................................. 25 EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 4 1. GENERAL INFORMATION 1.1 Verification of Compliance EUT: MINI ASSET TAG Model: IT-712E/IT-709E/IT-722E ( all models are electrical identical ) Applicant: CENTRAK, INC. Test Type: FCC Part 15.249 & IC RSS-210 (Issue 8) A2.9 & RSS-Gen (Issue 3) Result: PASS Tested by: ADVANCED COMPLIANCE LABORATORY Test Date: Dec. 17, 2014 Report Number: 0048-141121-01 The above equipment was tested by Compliance Laboratory, Advanced Technologies, Inc. for compliance with the requirement set forth in the FCC rules and regulations Part 15 subpart C. This said equipment in the configuration described in the report, shows the maximum emission levels emanating from equipment are within the compliance requirements. The estimated uncertainty of the test result is given as following. The method of uncertainty calculation is provided in Adva…

Text truncated - open the document above for the full version.

EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 10 EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 11 EUT name: MINI ASSET TAG Model No. IT-712E/IT-709E/IT-722E FCC ID: ST2-IT712E, IC:6012A-IT712E ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 12 Figure 3.1 Radiated Test Setup