T34NHXN118RLF

NOTE This device complies with part 18 of the FCC Rules. 1, Before commissioning this oven please read this instruction manual and keep it carefully. 2, There must be more than 30cm high space necessary above the top surface of oven. 3, Do not repair the oven yourself, please consult an authorized expert. 4, The contents of feeding bottles and bay food jars are to be stirred or shaken and the temperature is to be checked before consumption, in order to avoid burns. 5, Check the oven and the cable regularly for damage. If there is any kind of damage, the oven should not be used. „ Do not attempt to operate this oven with the door open since open- door operation can result in harmfulexposure to microwave energy. It is important not to defeat or tamper with the safety interlocks. „ Carefully clean door seala and sealing surfaces. „ Do not operate the oven if it is damaged. It is particularly important that the oven door close properly and that there is no damage to the : (1) door(bent). (2) hinges and latches( broken or loosened). (3) door seals and sealing surfaces. „ Utensils sould be checked to ensure that they are suitable for use in microwave ovens. „ When heating food in plastic or paper containers, check the oven frequently due to the possibility of ignition. „ Microwave heating of beverages can result in delayed eruptive boiling, therefore care has to be taken when handling the container. „ If smoke is observed, switch off or unplug the appliance and keep the door closed in order to stifle any flames. „ Egg in their shell and whole hard- bolled eggs shall not be heated in microwave ovens since they may explode. „ If the door or door seals are damaged. The oven must not be operated until it has been repaired by a trained person. „ Liquids or other foods must not be heated in sealed containers since they are liable to explode. Warning: 1, It is hazardous for anyone other than a trained person to carry out any service or repair operation, which involves the removal of any cover which gives protection against exposure to microwave energy. 2, Only allow children to use the oven without supervision when adequate instructions have been given so that the children is able to use the oven in a safe way and understands the hazards of improper use. 3, If the supply cord is damaged, it must be replaced by the manufacture of its service agent or a similarly qualified person in order to avoid a hazard. 4, This product will make disturbance in AV product, if any disturbance is occurred, use different electrical source jack to supply electricity or use low power or away from them. Note: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZATED MODIFICATIONS TO THIS EQUIPMENT .SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

External Photos Model: XN126 EUT-Top View EUT-Bottom View Model: XNXXX EUT-Top View EUT-Bottom View Model: XN118 EUT-Top View EUT-Bottom View Model: XN213 EUT-Top View EUT-Bottom View Model: XN218 EUT-Top View EUT-Bottom View Model: XN226 EUT-Top View EUT-Bottom View Model: XN130 EUT-Top View EUT-Bottom View Model: XN132 EUT-Top View EUT-Bottom View Model: XN142 EUT-Top View EUT-Bottom View

ID Label Label FCC ID: T34NHXN118

ID Label/Location Label Location Information Specifications: Text is Black or white in color and is left justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Label Location Model: XN126 Model: XNXXX Model: XN118 Model: XN213 Model: XN218 Model: XN226 Model: XN130 Model: XN132 Model: XN142

Internal Photos Model: XN126 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XNXXX EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN118 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN213 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN218 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN226 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN130 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN132 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View Model: XN142 EUT-Uncovered View (1) EUT-Uncovered View (2) EUT-Inside View EUT-PCB Top View EUT-PCB Bottom View

Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Bay Area Compliance Lab Corp. (ShenZhen). This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the US Government. FCC PART 18 EMI MEASUREMENT AND TEST REPORT For XING NAN LIGHTING CO., LTD Luowu Road, Luocun Town, Nanhai, Foshan, Guangdong, China FCC ID: T34NHXN118 April 28, 2006 This Report Concerns: Original Report Equipment Type: RLF Test Engineer: Louise Lu Report Number: RSZ06031481 Test Date: April 26, 2006 Reviewed By: Chris Zeng Prepared By: Bay Area Compliance Lab Corp. (ShenZhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone, ShenZhen, GuangDong 518038, P.R.China Tel: +86-755-33320018 Fax: +86-755-33320008 XING NAN LIGHTING CO., LTD FCC ID: T34NHXN118 Report # RSZ06031481 Page 2 of 30 FCC Part 18 ID Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................................3 O BJECTIVE ...................................................................................................................................................................3 R ELATED S UBMITTAL ( S )/G RANT ( S ).............................................................................................................................3 T EST M ETHODOLOGY ..................................................................................................................................................3 TEST FACILITY.............................................................................................................................................................3 EXTERNAL I/O CABLE.................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 JUSTIFICATION.............................................................................................................................................................5 EQUIPMENT MODIFICATIONS.......................................................................................................................................5 CONFIGURATION OF TEST SETUP.................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................5 CONDUCTED EMISSION...........................................................................................................................................6 MEASUREMENT UNCERTAINTY....................................................................................................................................6 EUT SETUP..................................................................................................................................................................6 EMI TEST RECEIVER SETUP........................................................................................................................................7 TEST EQUIPMENT LIST AND DETAILS...........................................................................................................................7 TEST PROCEDURE........................................................................................................................................................7 TEST RESULTS SUMMARY............................................................................................................................................7 TEST DATA..................................................................................................................................................................8 P LOT ( S ) OF T EST D ATA ..............................................................................................................................................12 XING NAN LIGHTING CO., LTD FCC ID: T34NHXN118 Report # RSZ06031481 Page 3 of 30 FCC Part 18 ID Report GENERAL INFORMATION Product Description for Equipment Under Test (EUT) The XING NAN LIGHTING CO., LTD ’s model: XN126, XNXXX, XN118,XN213,XN218,XN226,XN130,XN132,XN142, or the “EUT” as referred to in this report is a RLF which measures approximately 11.6 cmL x 5.1 cmW x 2.0 cmH, rated input voltage: AC 120V/60Hz. * The test data gathered are from production sample, serial number: 0603203 provided by the manufacturer, we received EUT on 2006-3-14. Objective The following test report is prepared on behalf of XING NAN LIGHTING CO., LTD in accordance with Part 2, Subpart J, and Part 18, Subparts A, B and C of the Federal Communication Commissions rules and regulations. The objective of the manufacturer is to determine compliance with FCC Part 18 limits. Related Submittal(s)/Grant(s) No related submittal(s). Test Methodology All measurements contained in this report were conducted with MP-5, FCC Methods of Measurements of Radio Noise Emissions from ISM Equipment, February 1986. All measurement was performed at Bay Area Compliance Lab Corp. (ShenZhen). The radiated testing was performed at an antenna-to-EUT distance of 3 meters. Test Facility The Test site used by Bay Area Compliance Lab Corp. (ShenZhen) to collect radiated and conducted emission measurement data is located in the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone, ShenZhen, GuangDong 518038, P.R.China. Test site at Bay Area Compliance Lab Corp. (…

Text truncated - open the document above for the full version.

Test Setup Photos Model: XN126 Conducted Emission - Front View Conducted Emission – Side View Model: XNXXX Conducted Emission - Front View Conducted Emission – Side View Model: XN118 Conducted Emission - Front View Conducted Emission – Side View Model: XN213 Conducted Emission - Front View Conducted Emission – Side View Model: XN218 Conducted Emission - Front View Conducted Emission – Side View Model: XN226 Conducted Emission - Front View Conducted Emission – Side View Model: XN130 Conducted Emission - Front View Conducted Emission – Side View Model: XN132 Conducted Emission - Front View Conducted Emission – Side View Model: XN142 Conducted Emission - Front View Conducted Emission – Side View