T5W-ST162AIS receiver and transponder Portable Test Set

Shine Micro, Inc. AIS Test Set ST162 © Copyright Shine Micro, Inc., 2011. All rights reserved. DCM-T162-UMX Revision: 1.0 Page - 1 -of 43 Shine Micro, INC. ST162 SERIES AIS TEST SETS USER MANUAL Rev 1.0 Shine Micro, Inc. 9405 Oak Bay Road Port Ludlow, WA 98365 360-437-2503 www.shinemicro.com Shine Micro, Inc. AIS Test Set ST162 © Copyright Shine Micro, Inc., 2011. All rights reserved. DCM-T162-UMX Revision: 1.0 Page - 2 -of 43 Precautions ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. Immediately turn off the power if the equipment is emitting smoke or fire. Continued use of the equipment can cause fire or electrical shock. Contact a Shine Micro agent for service. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. AVOID storing equipment in areas with temperatures below –30°C (-22°F) or above +70°C (158°F). DO NOT place the test set where hot or cold air blows directly on it. Always remove any dirt or moisture before closing the cover. Avoid opening the battery compartments in the rain. Allowing moisture into the battery compartments can cause permanent damage to the unit. Shine Micro, Inc. AIS Test Set ST162 © Copyright Shine Micro, Inc., 2011. All rights reserved. DCM-T162-UMX Revision: 1.0 Page - 3 -of 43 Table of Contents Precautions ........................................................................................................................ - 2 - Table of Contents ............................................................................................................... - 3 - List of Figures..................................................................................................................... - 5 - List of Tables ...................................................................................................................... - 6 - 1 Introduction .................................................................................................................. - 7 - 1.1 Limited Warranty ................................................................................................... - 7 - 1.2 Return Goods Authorization Policy ....................................................................... - 7 - 1.3 FCC Warning..........................................................................................................- 8 - 1.4 Industry Canada Warning.......................................................................................- 8 - 2 Product Description & Design Features .................................................................... - 10 - 3 Technical Specifications ............................................................................................ - 11 - 4.1 Unpacking and Inspecting Equipment ................................................................. - 13 - 4.2 Required Equipment: ....................................................................................... - 13 - 4.3 Optional Equipment: ........................................................................................ - 13 - 5 Operational Overview ................................................................................................ - 14 - 5.1 VHF Antenna and Cable Considerations......................................................... - 14 - 5.2 GPS Antenna and Cable Considerations ........................................................ - 14 - 5.3 Data Connections ............................................................................................ - 14 - 5.4 Power-Up Test ................................................................................................. - 14 - 5.5 Factory Default Messages ............................................................................... - 15 - 6 Front Panel Indicators ............................................................................................... - 16 - Appendix A - RS-232 Port................................................................................................ - 18 - Appendix B – Bluetooth Serial Port (Optional)................................................................. - 19 - Overview: ................................................................................................................... - 19 - Configuring Bluetooth Communication: ..................................................................... - 19 - Appendix C – ST162 Configuration Manager .................................................................. - 22 - Test Set Customization ............................................................................................. - 22 - Use of ST162 Configuration Manager ....................................................................... - 22 - Tab: Load Configuration File............................................................................... - 23 - Tab: GPS ............................................................................................................ - 25 - Tab: Test Set Static Data .................................................................................... - 27 - Set Name, Call Sign and Dimensions: ....................................................... - 28 - Set Ship Cargo, Destination and Arrival Time:........................................... - 28 - Tab: Custom........................................................................................................ - 29 - Simulated Ships: ........................................................................................ - 30 - Shine Micro, Inc. AIS Test Set ST162 © Copyright Shine Micro, Inc., 2011. All rights reserved. DCM-T162-UMX Revision: 1.0 Page - 4 -of 43 Safety Related Message (SRM): ................................................................- 31 - SART Message:..........................................................................................- 32 - Tab: Reset ...................................................…

Text truncated - open the document above for the full version.

LAB-T162-0BT rev 1.0 Make horizontal cuts first FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 FCC ID: T5W-ST162 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162

LAB-T162-1BT rev 1.0 Make horizontal cuts first FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411 FCC ID: T5W-ST162 Contains FCC ID:T9J-R41-1 MODEL:ST162 This device complies with Part 15 of FCC Rules and with RSS-210 of the Industry Canada Certification Bureau.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Shine Micro, Inc. Made in U.S.A. IC: 7487A-ST162 Contains IC:6514A-RN411

Shine Micro, Inc. AIS Test Set Final Assembly Procedure ©Copyright Shine Micro, Inc., 2010. All rights reserved. DPA-T162-TXB Revision: 0.2 Page 5 of 5 4.4. Installation of Serial/ID label 4.4.1. The Thermal Printer is used for creating this label. Use the file named LAB-T162-SR1 fill out all of the fields with the correct unit data. Print the label. 4.4.2. The label should be applied on the back side of the enclosure between the two hinges. The highlighted green area in the figure below shows the accepted area for the serial label to be applied. 4.4.3. After the label is applied it should look something like the photo below. -End of Procedure-

1 Clark, RandyFrom: [email protected] Sent: Thursday, March 10, 2011 1:32 PM To: TCB Subject: Response to Inquiry to FCC (Tracking Number 665555) (TCB) Importance: High FCC Home | Search | RSS | Updates | E-Filing | Initiatives | Consumers | Find Peopl e Office of Engineering and Technology Inquiry: We have a product with an alternate label placement requiring FCC review because the product does not meet the normal criteria specified in KDB 784748. The product is a benchtop device which comes in a s ealed closable NEMA rated enclosure. The lid closes with snap-lock style clasps. The manufacturer has requested the ID label placement on the interior of the lid of the enclosure. In review of KDB 784748, we believe that this represents a valid placement because: 1) The lid is not intended to be removed, it is secured with non-removable pins. 2) In order to operate the equipment, the lid must be opened making the ID Label readily visible during use of t he equipment. 3) There are no special tools require d to open the lid Please let us know if this placem ent ca n be approved. Response: The placement shows the proposed label as being rea dily visible during use of the equipment. You also attest to the fact there are ?no special tools required to open the lid?. This placement can be ap proved. Do not reply to this message. Please select the Reply to an Inquiry Response link from the OET Inquiry System to add any additio nal information pertaining to this inquiry.

This report contains a total of 33 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Shine Micro INC. ADDENDUM TEST REPORT TO 91642‐5 AIS Test Set, ST162 Tested To The Following Standards: FCC Part 15 Subpart C Sections 15.209 and RSS‐210 Issue 8 Report No.: 91642‐5A Date of issue: March 10, 2011 This test report bears the accreditation symbol indicating that the testing performed herein meets the test and reporting requirements of ISO/IEC 17025 under the applicable scope of EMC testing for CKC Laboratories, Inc. We strive to create long‐term, trust based relationships by providing sound, adaptive, customer first testing services. We embrace each of our customers’ unique EMC challenges, not as an interruption to set processes, but rather as the reason we are in business. Page 2of 33 Report No.: 91642‐5A TABLE OF CONTENTS Administrative Information .......................................................................................................................... 3 Test Report Information ............................................................................................................................................ 3 Revision History ......................................................................................................................................................... 3 Report Authorization ................................................................................................................................................. 3 Test Facility Information ............................................................................................................................................ 4 Site Registration & Accreditation Information .......................................................................................................... 4 Summary of Results ................................................................................................................................................... 5 Conditions During Testing ......................................................................................................................................... 5 Equipment Under Test ............................................................................................................................................... 6 Peripheral Devices ..................................................................................................................................................... 6 FCC Part 15 Subpart C ................................................................................................................................... 7 15.209(a) Power Output ............................................................................................................................................ 7 15.209(a) Radiated Spurious Emissions ..................................................................................................................... 9 15.209(a) Bandedge ................................................................................................................................................. 25 15.215(c) 20dB Bandwidth ...................................................................................................................................... 28 RSS‐210 ....................................................................................................................................................... 30 99 % Bandwidth ....................................................................................................................................................... 30 Supplemental Information .......................................................................................................................... 32 Measurement Uncertainty ...................................................................................................................................... 32 Emissions Test Details .............................................................................................................................................. 32 Page 3of 33 Report No.: 91642‐5A ADMINISTRATIVE INFORMATION Test Report Information REPORT PREPARED FOR: REPORT PREPARED BY: Shine Micro INC. 9405 Oak Bay Road Port Ludlow, WA 98365 Joyce Walker CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 Representative: Mark SupikProject Number: 91642 Customer Reference Number: 1102171CKC05 DATE OF EQUIPMENT RECEIPT: February23, 2011 DATE(S) OF TESTING: February23 ‐24, 2011 Revision History Original: Testing of the AIS Test Set, ST162 to FCC Part 15 Subpart C Sections 15.209 and RSS‐210 Issue 8 Addendum A: To add clarification when readings were actually ambient readings and to add a separate data sheet just for power output. Report Authorization The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be used to claim product endorsement by A2LA or any government agencies. This test report has been authorized for release under quality control from CKC Laboratories, Inc. Steve Behm Director of Quality Assurance & Engineering Services CKC Laboratories, Inc. Page 4of 33 Report No.: 91642‐5A Test Facility Information Our laboratories are configured to effectively test a wide variety of product types. CKC utilizes first class test equipment, anechoic chambers, data acquisition and information services to create accurate, repeatable and affordable test results. TEST LOCATION(S): CKC Laboratories, Inc. 22116 23rd Drive S.E., Suite A Bothell, WA 98021‐4413 Site Registration & Accreditation Information Location CB # Japan Canada FCC Bothell US0081 R‐2296, C‐2506, T‐1489 & G‐2…

Text truncated - open the document above for the full version.