T7HCT8066DECT Communicator

M166C/CL Communicator Reference Guide 1 M166C/CL DECT Communicator Reference Guide Package Contents: - M166C/CL DECT Communicator - Battery - Belt clip - Lanyard cord - Desktop Charger - Power Supply - This Reference Guide - Additional Information sheet Front View Side Views Rear View M166CL Speaker DECT Locator DLB Lanyard cord Rear View M166C Speaker Operation state LEDs Label Alarm2 button Headset / Tear-off connector 2 M166C/CL Communicator Reference Guide GETTING STARTED Press the on/off button Press the front button (Alarm1 button) to start an alarm message or call to a predefined destination Press the front button (Alarm2 button) to start an alarm message or call to a predefined destination Press front and top button simultaneously (only available if enabled by the system administrator) + Short press any button Long press (3 seconds) any button Press the front (Alarm1 button) until you hear a beep Pull the cord out of the headset connector LED Indications LEDs at the top: Green LED – Voice call (either ringing or active) Red LED – Device is charging Blue LEDs at the front side: Left + right LED flash – Night visibility flash (if activated by the system administrator) Top – left+right – bottom flash – Alarm waiting for confirmation Right-going-turn—around - Incoming call On/Off button LED Flashes at a 5 seconds interval until the device has been switched off Switching the M166 on Activatin g an Alarm by pressing the front button (Alarm1 button) Activating an Alarm by pressing the top button (Alarm2 button) Cancelling an alarm Answerin g an incoming call Re jecting (or cancelling) a call Switchin g the M166 off Makin g a pull cord alarm Additi o A Only auth o Charg the Ada p The Batt e fully Alw a • • • • Ca u • • Like inter Imp Imp Sen onal Information G Addition use this pr orised its ope ge the batter M166C/CL D pter (EU91706 M166C/CL D ery which can discharged). ays observe th Only use the the recomm e Never disasse Do not expos Do not char charger may cause the ba t ution Risk of expl Dispose of any radio‐ b ference wit portant Sa portant Ba nsitive Elec G266/G566d/G566 nal Info M166 D roduct in co eration. ry only while Desktop Char 69). Desktop Charg n be charged A typical life he following w battery deliv ended type – emble, custom se the battery rge the batt damage the ttery to explo osion if batte used batterie based equipm h other eq fety Inform attery Infor ctronic Equ 6s/Gx66 Desktop C ormatio Desktop untries whe installed in t ger powere d ger is fitted d for 300 – 5 expectancy f o with respect t vered with th NEC article c mize or short y to temperat teries by any battery and/ ode. ery is replaced es according t ment, the M quipment. H mation rmation uipment Charger/Gx66 Mul on M166 p Charg re the relev he M166C/C d by M166C/ with a 3.7V/ 00 charge cy or the battery to the battery e M166C/CL ode: EU9170 t‐circuit batte tures in exces y other mea /or the M166 d by an incorr to the instruct M166C/CL ca owever due lti Charger Rack 6C/CL a ger vant authorit L in combinat /CL Multi Re /400mAh Lit ycles (fully ch y is 2 to 3 yea y: (or a spare b 73). eries. ss of 60⁰C (14 ans! Using a 6C/CL and mi rect type. tions an potential e to the v Page 1 and ties have tion with egion AC hium‐Ion harged to ars. battery of 40⁰F). ny other ight even ly cause very low Additi o trans prove equip elect of se advis of eq Do n maki Obs e Charg Whe follo w • • • • • Ple yo u For Use Pro onal Information G smission pow es that oper pment. Even tronic equipm ensitive elect sed not to pla quipment, eve not rely on th ng indispensa erve all warn ger User Man n using the M wing: Do not ex p handset/char Do not use th Do not expos an extended Plug the AC a access/remo not cause a t Use the follo o ase also use ur telephone countries e of the M1 oduct Dispo G266/G566d/G566 wer level the c rational DECT so it is advis ment. When t ronic equipm ace the M166 en in standby he M166C/CL able calls (e.g ings and inst nual. M166C/CL De pose the M1 rger near wat he M166C/CL se the M166C period of tim adaptor in a w val of the AC rip hazard. w dedicated Ten Pao S0 0 O/P: DC 5V, 0 the other do system. in the Eur 166 Deskto osal Inform 6s/Gx66 Desktop C chances for in T phones no sed not to p the M166C/C ment incident 6C/CL on or c y mode. L as your onl g. an emergen tructions con esktop Charge 166C/CL to ter. L on premises C/CL to high t me. wall outlet so C adaptor. Ta power suppl y 04YM0500035 0.35A). cumentation ropean Uni op Charger mation Charger/Gx66 Mul nterference is ormally don’t lace the M16 L is operated tal influences close (less th y means of c ncy call). ntained in th er and its acc rain or mo subject to ex temperatures ocket near th ke care that y unit for the 5 (rating I/P: supplied wit ion lti Charger Rack s very small. t influence e 66C/CL near d in straight s can appear. an 10cm) to communicati e M166C/CL cessories obs oisture, nor xplosive haza s or direct sun e equipment the power c Desktop Cha :AC 100‐240V h the various Page 2 Research electronic sensitive nearness . You are this kind on when Desktop serve the use the rds. nlight for t for easy ord does rger, V, 0.15A; s parts of Additional Information G266/G566d/G566s/Gx66 Desktop Charger/Gx66 Multi Charger Rack Page 3 Be sure to dispose of these products as well as its packing material in an environmentally compatible way. Electrical equipment, including the battery, should not be disposed of as municipal waste. These products should be taken to a designated facility where the best available treatment, recovery and recycling techniques are available. At www.nec‐enterprise.com/About‐NEC/Environment/WEEE‐541 you can find information about separate disposal and environmentally sound recycling. For countries outside the European Union Disposal of electrical and electronic products in countries outside the European Union should be done in line with the local regulations. If no arrangement has been made with NEC or your supplier, please conta…

Text truncated - open the document above for the full version.

FCC ID: T7HCT8066

INTERTEK TESTING SERVICES External Photos –M166C external photos - 1 of 2 INTERTEK TESTING SERVICES External Photos –M166C external photos - 2 of 2

INTERTEK TESTING SERVICES External Photos- M166CL external photos - 1 of 3 INTERTEK TESTING SERVICES External Photos- M166CL external photos - 2 of 3 INTERTEK TESTING SERVICES External Photos- M166CL external photos - 3 of 3

50002044 RTX8066C Com label Daktel M166C Rev. B 29.6 12.7 2 : 1 1 : 1 Size: 29.6mm (W) x 12.7mm(H) Material: PET (comply with PGAA requirement) Barcode formt: 2D Datamatrix Color: Black text on white background Position: At the back appointed area of communicator Remarks: SN: YYWWXXXXXX YY: Manufacturing year WW: Manufacturing week of the year XXXXXX: Progressive serial no. range in decimal format. (The SN on communicator label, charger label and giftbox label must be matched). IPEI in Hex format: 0XXXXXXXXX 1st digit: 0 (fixed information) 23-04-2015 2D Barcode information: 1) EU917065 2) 0XXXXXXXXX 3) YYWWXXXXXX (Information showed horizontally after scanned: e.g. EU917063;0XXXXXXXXX;YYWWXXXXXX) 3.7V 400mAh SN: YYWWXXXXXX IPEI: 0XXXXXXXXX Model: M166C DECT Communicator Made in China FCC ID: T7HCT8066 IC: 4979B-CT8066 Electrical Safety- UL 60950-1 2D Data- matrix 127796 NEC Nederland B.V. 3.7V 400mAh SN: YYWWXXXXXX IPEI: 0XXXXXXXXX Model: M166C DECT Communicator Made in China FCC ID: T7HCT8066 IC: 4979B-CT8066 Electrical Safety- UL 60950-1 2D Data- matrix 127796 NEC Nederland B.V. 50002050 RTX8066CL Com label Daktel M166CL Rev. B23-04-2015 29.6 12.7 2 : 1 1 : 1 Barcode information: 1) EU917066 2) 0XXXXXXXXX 3) YYWWXXXXXX (Information showed horizontally after scanned: e.g. EU917064;0XXXXXXXXX;YYWWXXXXXX) Size: 29.6mm (W) x 12.7mm(H) Material: PET (comply with PGAA requirement) Barcode formt: 2D Datamatrix Color: Black text on white background Position: At the back appointed area of communicator Remarks: SN: YYWWXXXXXX YY: Manufacturing year WW: Manufacturing week of the year XXXXXX: Progressive serial no. range in decimal format. (The SN on communicator label, charger label and giftbox label must be matched). IPEI in Hex format: 0XXXXXXXXX 1st digit: 0 (fixed information) 3.7V 400mAh Model: M166CL DECT Communicator Electrical Safety- UL 60950-1 2D Data- matrix 127796 SN: YYWWXXXXXX IPEI: 0XXXXXXXXX Made in China FCC ID: T7HCT8066 IC: 4979B-CT8066 NEC Nederland B.V. 3.7V 400mAh Model: M166CL DECT Communicator Electrical Safety- UL 60950-1 2D Data- matrix 127796 SN: YYWWXXXXXX IPEI: 0XXXXXXXXX Made in China FCC ID: T7HCT8066 IC: 4979B-CT8066 NEC Nederland B.V.

INTERTEK TESTING SERVICES Internal photos internal photos - 1 of 7 INTERTEK TESTING SERVICES Internal photos internal photos - 2 of 7 INTERTEK TESTING SERVICES Internal photos internal photos - 3 of 7 INTERTEK TESTING SERVICES Internal photos internal photos - 4 of 7 INTERTEK TESTING SERVICES Internal photos internal photos - 5 of 7 INTERTEK TESTING SERVICES Internal photos internal photos - 6 of 7 INTERTEK TESTING SERVICES Internal photos internal photos - 7 of 7

INTERTEK TESTING SERVICES Internal photos internal photos - 1 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 2 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 3 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 4 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 5 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 6 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 7 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 8 of 9 INTERTEK TESTING SERVICES Internal photos internal photos - 9 of 9

Report No.: 15010541HKG-001 Page 1 of 91 - The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com Specific Absorption Rate (SAR) Evaluation Report For DECT Communicator Model Number: M166CL Additional Model: M166C Brand Name: NEC FCC ID: T7HCT8066 Test Report: 15010541HKG-001 Date of Report: 13 April 2015 Prepared for RTX Hong Kong Limited 8/F, Corporation Square, 8 Lam Lok Street, Kowloon Bay, Hong Kong Prepared and Checked by: Approved by: Chan Chun Foo, Bike Senior Lead Engineer Date: 13 April, 2015 Nip Ming Fung, Melvin Assistant Manager Date: 13 April, 2015 Report No.: 15010541HKG-001 Page 2 of 91 Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com Table of Contents 1 Test Result Summary.................................................................................................. 3 2 General Information..................................................................................................... 4 3 Measurement System Description and Procedure ...................................................... 6 4 Tissue Verificaiton ..................................................................................................... 14 5 SAR Measurement System Verification.................................................................... 16 6 SAR Evaluation ......................................................................................................... 18 7 Test Insturments........................................................................................................ 24 8 Measurement Uncertainty ........................................................................................ 25 9 E-Field Probe and Dipole Antenna Calibration ......................................................... 25 10 References ............................................................................................................... 25 APPENDIX A – System Verification Data...................................................................... 26 APPENDIX B – SAR Evaluation Data ........................................................................... 28 APPENDIX C – E-Field Probe and Dipole Antenna Calibration .................................... 44 APPENDIX D – SAR Tissue Specification .................................................................... 90 APPENDIX E – SAR System Validation........................................................................ 91 Report No.: 15010541HKG-001 Page 3 of 91 Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com 1. Test Result Summary *Note: 1. Model: M166C is the same as the Model: M166CL in Electrical designs, including software&firmware and PCB layout. The only difference in Cosmetic details, model number, pluggable low frequency location detector module, rear housing and speaker between these models are for marketing purpose only. The maximum spatial peak SAR value for the sample device averaged over 1g was found to be: Highest Reported SAR Band Operating Mode TX Frequency (MHz) 1g In-front-of face 1g Body 1.9GHz Voice Transmission 1921.536 – 1928.448 0.074 W/kg 0.095 W/kg This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment / general population exposure limits specified in ANSI/IEEE C95.1. Applicant : RTX Hong Kong Limited Applicant Address : 8/F, Corporation Square, Lam Lok Street, Kowloon Bay, Hong Kong Model* : M166CL M166C Brand Name : NEC EUT Description : DECT Communicator Exposure Category : General Population/Uncontrolled Exposure Test Device : Production Unit Date of Sample Received : 15 January, 2015 Date of Test : 10 February, 2015 to 11 February, 2015 Date of Report : 13 April, 2015 Place of Testing : Intertek Testing Services Hong Kong Workshop No. 3, G/F, World-wide Industrial Centre, 43-47 Shan Mei Street, Fotan Shatin, N.T., Hong Kong Temperature: +20 to 25°C Environmental Conidtions : Humidity 30 to 70% Test Specification : ANSI/IEEE C95.1: 1992 IEEE Std 1528: 2003 IEEE Std 1528a: 2005 FCC KDB Publication 447498 D01 v05r02 FCC KDB Publication 865664 D01 v01r03 FCC KDB Publication 865664 D02 v01r01 Report No.: 15010541HKG-001 Page 4 of 91 Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com 2. General Information 2.1. Description of Equipment under test (EUT) Nominal and Maximum Output Power Specifications The EUT operates using the following maximum and nominal output power specifications…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES FCC ID: T7HCT8066 Page of 2 1 Front, 0mm separation Back, 0mm separati on INTERTEK TESTING SERVICES FCC ID: T7HCT8066 Page of 2 2 Back with belt clip, 0mm separation

INTERTEK TESTING SERVICES FCC ID: T7HCT8066 Page 1 of 2 EUT Photo Figure 1 – Handset Unit front view Figure 2 – Handset Unit back view INTERTEK TESTING SERVICES FCC ID: T7HCT8066 Page 2 of 2 Figure 3 – Handset Unit With Belt Clip back View

- Intertek’s standard Terms and Conditions can be obtained at our website: http://www.intertek.com/terms/. - The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report Number: 15010540HKG-001 Application For Original Grant of 47 CFR Part 15 Certification New Family of RSS-213 Issue 3 Equipment Certification Unlicensed Personal Communication Service Devices/ 2 GHz License-exempt Personal Communications Service Devices (DECT Communicator) FCC ID: T7HCT8066 IC: 4979B-CT8066 Prepared and Checked by: Approved by: Chak Chun Yin, Ray Nip Ming Fung, Melvin Assistant Engineer Assistant Manager March 26, 2015 INTERTEK TESTING SERVICES Test Report Number: 15010540HKG-001 Page 1 of 62 FCC ID: T7HCT8066 IC: 4979B-CT8066 GENERAL INFORMATION Applicant Name: RTX Hong Kong Limited Applicant Address: 8/F., Corporation Square, 8 Lam Lok Street, Kowloon Bay, Hong Kong FCC Specification Standard: FCC Part 15, October 1, 2013 Edition FCC ID: T7HCT8066 FCC Model(s): M166C, M166CL IC Specification Standard: RSS-213 Issue 3, March 2015 RSS-Gen Issue 3, December 2010 IC: 4979B-CT8066 IC Model(s): M166C, M166CL Type of EUT: Unlicensed Personal Communications Service Devices Description of EUT: DECT Communicator Serial Number: N/A Sample Receipt Date: January 15, 2015 Date of Test: February 11 - March 11, 2015 Report Date: March 26, 2015 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Test Report Number: 15010540HKG-001 Page 2 of 62 FCC ID: T7HCT8066 IC: 4979B-CT8066 Table of Contents 1.0 Test Results Summary & Statement of Compliance.............................................. 5 1.1 Summary of Test Results ....................................................................................... 5 1.2 Statement of Compliance ....................................................................................... 7 2.0 General Description................................................................................................. 9 2.1 Product Description ................................................................................................. 9 2.2 Technical Description .............................................................................................. 9 2.3 Test Methodology.................................................................................................... 9 2.4 Test Facility............................................................................................................. 9 3.0 System Test Configuration.................................................................................... 11 3.1 Justification ........................................................................................................... 11 3.2 Conducted Emission Test Configuration ................................................................ 12 3.3 Conducted Monitoring and Operational Test Configuration .................................... 12 3.4 EUT Exercising Software....................................................................................... 12 3.5 Details of EUT and Description of Accessories ...................................................... 13 3.6 Measurement Uncertainty ..................................................................................... 13 4.0 Measurement Results............................................................................................ 15 4.1 Antenna Requirement ........................................................................................... 15 4.2 Digital Modulation Techniques............................................................................... 15 4.3 Emission Bandwidth .............................................................................................. 16 4.4 Directional Gain of the Antenna ............................................................................. 19 4.5 Peak Transmit Power ............................................................................................ 20 4.6 Power Spectral Density ......................................................................................... 23 4.7 Automatic Discontinuation of Transmission............................................................ 26 4.8 Unwanted Emission Inside the Sub-Band .............................................................. 27 4.9 Emissions Outside the Sub-Band .......................................................................... 31 4.9.1 Radiated Emissions Configuration Photographs ................................................. 32 4.9.2 Radiated Emissions Data ................................................................................... 32 4.9.3 Field Strength Calculation................................................................................... 39 4.9.4 Average Factor Calculat…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: T7HCT8066 IC: 4979B-CT8066 Radiated Emission (M166C and M166CL) Front View Rear View