TG310G10PSTOY Transmitter

FKA Distributing Co., LLC Date: 8/3/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(5) Attestation FCC ID: TG310G10PS Grantee FRN: 0013791793 1. FKA Distributing Co., LLC certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. FKA Distributing Co., LLC (“the applicant”) certifies that, the device does not have cybersecurity and / or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered List installed on the device, nor will it be installed by the applicant anytime after certification. 3. FKA Distributing Co., LLC (“the applicant”) certifies that the RF device is not a router “produced in a foreign country”. 4. FKA Distributing Co., LLC certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Mark Straight Job Title: Senior Project Engineer Company Name: FKA Distributing Co., LLC

FKA Distributing Co., LLC Date: 7/22/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation FCC ID: TG310G10PS Grantee FRN: 0013791793 To whom it may concern: FKA Distributing Co., LLC (“the applicant”) as required by section §2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. Contact Person Mark Straight Company Name FKA Distributing Co., LLC FCC FRN: 0013791793 Company US Address 3000 N. Pontiac Trail Commerce Township, MI 48390 United States Email [email protected] Sincerely yours, Name: Mark Straight Job Title: Senior Project Engineer Company Name: FKA Distributing Co., LLC

FKA Distributing Co., LLC Date: 7/22/2026 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Company Name: FKA Distributing Co., LLC Contact Name: Mark Straight Title of Person: Senior Project Engineer Address: 3000 N. Pontiac Trail Commerce Township, MI 48390 United States

FKA Distributing Co., LLC Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: TG310G10PS To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: FKA Distributing Co., LLC Contact Name: Mark Straight Title of Person: Senior Project Engineer Address: 3000 N. Pontiac Trail Commerce Township, MI 48390 United States Date:7/22/2026

External Photographs Project No.: 4792323437 Page 2 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT Page 3 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 4 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch.

FCC Label Note: This would be a plastic label with a permanent adhesive. Label location

Internal Photographs Project No.: 4792323437 Page 2 of 3 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT Page 3 of 3 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Antenna

FCC ID: TG310G10PS According to 447498 D04 Interim General RF Exposure Guidance v01, 2.1.4 MPE-Based Exemption An alternative to the SAR-based exemption is provided in § 1.1307(b)(3)(i)(C), for a much wider frequency range, from 300 kHz to 100 GHz, applicable for separation distances greater or equal to λ/2π, where λ is the free-space operating wavelength in meters. The MPE-based test exemption condition is in terms of ERP, defined as the product of the maximum antenna gain and the delivered maximum time-averaged power.10 For this case, a RF source is an RF exempt device if its ERP (watts) is no more than a frequency-dependent value, as detailed tabular form in Appendix B. These limits have been derived based on the basic specifications on Maximum Permissible Exposure (MPE) considered for the FCC rules in § 1.1310(e)(1). B.4 SAR-based Exemption SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum time- averaged power or maximum time-averaged ERP, whichever is greater. If the ERP of a device is not easily determined, such as for a portable device with a small form factor, the applicant may use the available maximum time-averaged power exclusively if the device antenna or radiating structure does not exceed an electrical length of λ/4. As for devices with antennas of length greater than λ/4 where the gain is not well defined, but always less than that of a half-wave dipole (length λ/2), the available maximum time-averaged power generated by the device may be used in place of the maximum time-averaged ERP, where that value is not known. The separation distance is the smallest distance from any part of the antenna or radiating structure for all persons, during operation at the applicable ERP. In the case of mobile or portable devices, the separation distance is from the outer housing of the device where it is closest to the antenna. The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold Pth (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by Formula (B.2). and f is in GHz, d is the separation distance (cm), and ERP 20cm is per Formula (B.1). The example values shown in Table B.2 are for illustration only. -The maximum average field strength is 71.02 dBuV/m, the ERP= 71.02 - 97.4 = -26.38 dBm= 0.0023 mW, the maximum time-averaged power = -26.38 - 0= -27.47 dBm= 0.0023mW, the maximum time-averaged power＜3 mW. - When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Conclusion: No SAR is required.

Antenna Frequency (MHz) Antenna Type Maximum Antenna Gain (dBi) 1 2407-2477 PCB antenna 0 Antenna Size:

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. CFR 47 FCC PART 15 SUBPART C ISED RSS-210 Issue 11 TEST REPORT For TOY Transmitter MODEL NUMBER: 10G10PS REPORT NUMBER: 4792323437-1-RF-1 ISSUE DATE: Aug 5, 2026 FCC ID: TG310G10PS IC: 20834-10G10PS Prepared for For FCC: FKA Distributing Co., LLC 3000 N. Pontiac Trail Commerce Township, MI 48390 United States For ISED: HoMedics, Inc. 3000 Pontiac Trail Commerce Township MI 48390 United States Of America Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Room 101, Building 2, No.4, Information Road, Songshan Lake, Dongguan, Guangdong, China Tel: +86 769 22038881 Fax: +86 769 33244754 Website: www.ul.com REPORT NO.: 4792323437-1-RF-1 Page 2 of 56 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 Aug 5, 2026 Initial Issue Rex Huang REPORT NO.: 4792323437-1-RF-1 Page 3 of 56 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Clause Test Items ISED Rules Test Results 1 20dB Bandwidth CFR 47 FCC §15.215 (c) ISED RSS-Gen Clause 6.7 Pass 2 Radiated Emission CFR 47 FCC §15.249 (a)(d)(e) CFR 47 FCC §15.205 and §15.209 ISED RSS-210 Annex B B.10 RSS-GEN Clause 8.9 RSS-GEN Clause 8.10 Pass 3 Conducted Emission Test for AC Power Port CFR 47 FCC §15.207 RSS-GEN Clause 8.8 N/A (Note 2) 4 Antenna Requirement CFR 47 FCC §15.203 ISED RSS-Gen Clause 6.8 Pass Note 1: This test report is only published to and used by the applicant, and it is not for evidence purpose in China. Note 2: Conducted Emission Test for AC Power Port is not applicable, because the EUT is powered by non-rechargeable battery. Note 3: The measurement result for the sample received is <Pass> according to < CFR 47 FCC PART 15 SUBPART C, ISED RSS-210 ISSUE 11 >when <Simple Acceptance> decision rule is applied. REPORT NO.: 4792323437-1-RF-1 Page 4 of 56 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. CONTENTS 1. ATTESTATION OF TEST RESULTS ...................................................................................... 5 2. TEST METHODOLOGY .......................................................................................................... 6 3. FACILITIES AND ACCREDITATION ...................................................................................... 6 4. CALIBRATION AND UNCERTAINTY ..................................................................................... 7 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................ 7 4.2. MEASUREMENT UNCERTAINTY ............................................................................. 7 5. EQUIPMENT UNDER TEST .................................................................................................... 8 5.1. DESCRIPTION OF EUT ............................................................................................. 8 5.2. CHANNEL LIST .......................................................................................................... 8 5.3. MAXIMUM FIELD STRENGTH .................................................................................. 9 5.4. TEST CHANNEL CONFIGURATION ......................................................................... 9 5.5. THE WORSE CASE POWER SETTING PARAMETER ............................................ 9 5.6. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................ 9 5.7. DESCRIPTION OF TEST SETUP ............................................................................ 10 6. MEASURING EQUIPMENT AND SOFTWARE USED ......................................................... 11 7. ANTENNA PORT TEST RESULTS ...................................................................................... 12 7.1. 99% OCCUPIED BANDWIDTH ................................................................................ 12 7.2. DUTY CYCLE ........................................................................................................... 19 8. RADIATED TEST RESULTS ................................................................................................ 21 8.1. FUNDAMENTAL EMISSION .................................................................................... 30 8.2. RESTRICTED BANDEDGE ..................................................................................... 33 8.3. SPURIOUS EMISSIONS (1 GHZ ~ 3 GHZ) ............................................................. 37 8.4. SPURIOUS EMISSIONS (3 GHZ ~ 18 GHZ) ........................................................... 43 8.5. SPURIOUS EMISSIONS (9 KHZ ~ 30 MHZ) ........................................................... 49 8.6. SPURIOUS EMISSIONS (18 GHZ ~ 26 GHZ) ......................................................... 52 8.7. SPURIOUS EMISSIONS (30 MHZ ~ 1 GHZ) ........................................................... 54 9. ANTENNA REQUIREMENT .................................................................................................. 56 REPORT NO.: 4792323437-1-RF-1 Page 5 of 56 UL Verification Services (Gu…

Text truncated - open the document above for the full version.

Appendix II Setup Photographs Project No.: 4792323437-1 Page 2 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Radiated Band edge and Spurious Emission RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz) MEASUREMENT POSITION MEASUREMENT POSITION (X axis) Page 3 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. MEASUREMENT POSITION (Y axis) MEASUREMENT POSITION (Z axis) Page 4 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. RADIATED RF MEASUREMENT SETUP (30MHz~1GHz) RADIATED RF MEASUREMENT SETUP (Below 30MHz)