TQ4YWGIT-R5678902RFID READER

※※※CAUTION※※※ changes of modifications not expressly approved by the part responsible for compliance could void the user , s authority to operate the equipment。 XCRF-502C Reader User manual Table of Contents 1 INTRODUCTION..................................................... 2 2 PERFORMANCE PARAMETER............................................ 4 2.1 GENERAL FEATURES...................................................4 2.2 KEY FEATURE.......................................................4 2.3 TECHNICAL SPECIFICATION.............................................4 3 DESIGN FUNDAMENTALS.............................................. 5 3.1 DEVICE COMPOSE....................................................5 3.1.1 RF unit: .....................................................5 3.1.2 Baseband unit: ...............................................5 3.1.3 Power unit: ..................................................6 3.1.4 data interface unit: .........................................6 3.1.5 case unit: ...................................................6 3.2 FUNDAMENTAL WORKING PRINCIPLE.........................................6 4 USAGE AND OPERATION.............................................. 7 4.1 READER CONNECTION..................................................7 4.2 READER USAGE AND OPERATION...........................................7 5 USUAL FAILURE ANALYSIS AND EXCLUSION ............................. 7 6 OTHER NOTICE..................................................... 7 6.1 PRODUCTION WARRANTY................................................7 6.2 SAFETY NOTE.......................................................8 1 Introduction Thank you for using XCRF-502C reader made in Shenzhen Invengo Information Technology Co. Ltd. The reader can offer stability and reliability, while strictly following the ISO-18000-6B recommendation.. Front panel and rear panel layout XCRF-502C reader layout as below: figure 2－1: figure 2－1 XCRF-502C reader front panel layout 1－I/O port, have four input ports and four output ports with photoelectricity isolation showed on DB15 connector; 2－RS-232 serial port, a physical interface between a computer and reader. The pin no, signal name and direction list as below. And the pin number is same as the number showed on DB9 connector. pin signal direction 2 RXD input 3 TXD output 5 Ground ground 3－Network Interface between a computer and reader. Plug one end of the cable into the RJ45 jack on the back of your PC. Plug the other end into RJ45 port on the reader. Device provides 10M Ethernet interfaces. 4－antenna port1; 5－antenna port2; Note: Every antenna port must connect with an antenna or 50 ohm load before the reader power up. otherwise the reader will be damaged. XCRF-502C reader rear panel figure 2－2: figure 2－2 XCRF-502C reader rear panel figure 2－2 1－AC INLET; 2－Power Indicator, green-colour light, green light indicates that the reader power on; 3－Power Amplifier Indicator, red-colour light, Red light indicates the reader is transmitting Radio frequency power from RF port; 4－Link Indicator ,green light, green light indicates that the Reader has linked with Computer from Ethernet network port; 5－Communication, blue light, ,blue lighting indicates that the reader is communicating with computer ; 6－Receive light, green lighting indicates that the reader is communicating with the tag; 7－power switch; 2 Performance Parameter 2.1 General Features ·Operating temperature:－10°C～＋60°C(14°F～＋140°F) ·Storage temperature:－20°C～＋70°C(－4°F～＋158°F) ·Operating humidity:20％～95％ ·Power supply voltage:AC:100V～240V/200mA ·Size:29.5 x 23.0 x 7.0cm（11.6 x 9.0 x 2.8inches） ·Weight: about:3.0Kg（6.61lb） 2.2 Key feature ·Protocol:ISO-180006B ·Tag data rates:40kbps ·Number of antenna:up to 2 , electronically switched ·Antenna port isolation:≧22dB ·Transmitter type:On/Off Keying ·Usable channels:51 ·Occupied frequency bandwidth:＜400KHz 2.3 Technical specification ·Frequency of operating:902MHz ~928MHz ·Output power:1.0Watt（+30dBm） ·Frequency stability:≦±5ppm ·Operating mode: fixed-frequency /frequency hopping selective availability.maximal optional frequency number is 51pcs, frequency interval is 500KHz. ·Maximal reading distance up to 3.5~4.5m (11.48~14.75feet)（EIRP=36dBm,related to tags.） ·Write distance:Distances up to70％ of the read distance under the same condition. ·Multi-tag reading rate:≧60 pcs/second（it’s related to protocol） 3 Design fundamentals 3.1 Device compose As figure 4－1 and 4－2,XCRF-502C reader has 5 parts:RF unit, baseband unit,power unit、data interface unit、case unit. figure 4－1 reader RF unit fundamental block diagram figure 4－2 reader baseband unit fundamental block diagram 3.1.1 RF unit: →The RF unit receive baseband signal and modulate carrier,then amplify the modulated carrier signals and transmit the signals by selected antenna. →The unit receive the back scatter signal from the RFID tag.After demodulating , amplifying ,comparing the signals ,the unit transmit the signals up to baseband unit. →The unit adjust output power and frequency of the antenna interface under the control of the baseband unit. 3.1.2 Baseband unit: →The unit receive data & command from PC via RS-232 interface,or send data & results to PC ; →The unit transmit control signals of tags to RF unit; →The unit accept tag signals from RF unit, modulate signals and checkout; →The unit can modify or query configure information of reader under the control of PC command ; 3.1.3 Power unit: →converts incoming alternating current (AC) to direct current (DC),out DC power supply for the integrated equipment. 3.1.4 Data interface unit: →Standard connector to connect the COM port ,network and power interface with the rear panel of the integrated equipment ; 3.1.5 Case unit: →The reader case is made of molded-in Aluminum. 3.2 Fundamental working principle The complete RFID system is consist of XCRF-502C reader, antenna, tags, and pc. The baseband send the command to RF unit under the control of PC.RF unit send signa…

Text truncated - open the document above for the full version.

Block Diagram 1．System Module Block Diagram Radio Frequency Module Oscilator Fre=12.8MHz Base Band Module FPGA Fre=24.0MHz MCU Fre=24.0MHz LED Display Data Interface Power Module Power Data Signal RF signal System Module Block Diagram 2．Radio Frequency Module Block Diagram Radio Frequency Module Block Diagram 3．Base Band Module Block Diagram FPGA Fre=24.0M Hz MCU Fre=24.0M Hz LED Display power Data or I/O interface RF Module Oscilator Fre=12.8M Hz Base Band Module Block Diagram 4．Power Module Block Diagram AC/DC Module Input AC100~ 240V+5.0V +12V Power Module Block Diagram

Top View of EUT Bottom View of EUT Front View of EUT Back View of EUT Left View of EUT Right View of EUT Cable of System Antenna of System

Model Name: XCRF-502C Made in China FCC ID: TQ4YWGIT-R5678902 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Model Name: XCRF-502C Made in China FCC ID: TQ4YWGIT-R5678902 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Internal of EUT-1 Internal of EUT-2 Internal of EUT-3 Internal of EUT-4 Internal of EUT-5 Internal of EUT-6 Internal of EUT-7 Internal of EUT-8 Internal of EUT-9

System Description 1．System Structure Diagram Radio Frequency Module Oscilator Fre=12.8MHz Base Band Module FPGA Fre=24.0MHz MCU Fre=24.0MHz LED Display Data Interface Power Module Power Data Signal RF signal Diagram 1：System Structure Diagram The system is consist of radio frequency module, base band module, power module, data interface and LED display. under the control of base band module, radio frequency module transmits the modulated carrier signal with varying frequency and power. transmit the signal to a certain area by antenna within which the tags receive signal then feedback its signal. after going into the radio frequency module, the feedback signal will be demodulated to form base band signal. Base band performs decoding the tag signal and communicating with PC. and power module provide all the direct voltage. 2．Radio Frequency Structure Diagram Diagram 2：Radio Frequency Structure Diagram The radio frequency module is consist of transmitting and receiving parts controlled by Baseband circuit. the phase lock loop generates carrier with frequency range from 902MHz~928Mhz,which could be amplified by the front amplifier and end amplifier, then emitted by the antenna that return tag , s signal via demodulator to mixer where the signal is detected and amplified to output to the baseband circuit. The radio frequency module is consist of transmitting and receiving part, ·transmitting part The transmitting part is as below according to the RF signal flow. Temperature-compensated oscillator (12.8MHz) → PLL915A phase lock loop → RF2302 power front amplifier → end amplifier with power adjustable → microwave switcher with maximum output power 30dBm(1W). ·receiving part The receiving part is as below according to the return signal flow Demodulated network → front differential amplifier → end amplifier → comparator output → output double channel digital signal. 3．Base Band Structure Diagram FPGA Fre=24.0M Hz MCU Fre=24.0M Hz LED Display power Data or I/O interface RF Module Oscilator Fre=12.8M Hz Base Band Structure Diagram The baseband module is consist of coding/decoding part, and control parts, which respectively is FPGA and MCU. The coding/decoding part employs built-in-FLASH modeled FPGA .the FPGA performs coding/decoding for tag signal and controlling the transmitting circuit. The control unit employs MCU produced by Ubicom. with 19200serial interface and 10Mbps Etherent network interface, MCU performs order analyzing , data uploading ,and data storage etc. 4．Power Structure Diagram AC/DC Module Input AC100~ 240V+5.0V +12V Power Structure Diagram AC/DC Module input AC100~240V, Output voltage are +5VDC@3A and +12VDC@1A.

1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA File: 1 YWGIT 1 Time: Page Total Authorize WenyiqingStandardizationAuditor WenyiqingDesigner LiuTao C30.5pFC40.5pFC10.5pFC20.5pF C50.5pF OUTA 1 +INA 2 -INA 3 GND 4 +INB 5 -INB 6 OUTB 7 VCC 8 U36 MAX942 C660.1uF RF OUT R641.5k R67 1.2k L5 BLM31PG391 L6 BLM31PG391 R52 1k DEM1 R704.7k R71 4.7k C2010nF DEM4 C21 10nF DEM3 L9 8.2nH DEM2 L10 8.2nH R7851 R7951 +5V C71 100pF R84 1.2k R85 1.2k R88 200 C440.1uF D61N4148 R531k R80 120 R72 4.7k C101 0.1uF R734.7k 2 13 U32A MAT04 13 1412 U32B MAT04 6 75 U32CMAT04 D4 2822 D32822C8447pF C85 47pF C8 100pF C9100pF R3 62K R4 62K 9 810 U32D MAT04 D71N4148 C92 0.1uF C93 0.1uF C10710nF 2 13 U33A MAT04 C10610nF 13 1412 U33B MAT04 6 75 U33CMAT04 C100 0.1uF 9 810 U33D MAT04 C990.1uF C76100pF C103 4n7 C102 4n7 C75100pF C940.1uF C95 0.1uF C10410nF 9 810 U35D MAT04 C10510nF 6 75 U35C MAT04 13 1412 U35BMAT04 2 13 U35A MAT04 C98 0.1uF C97 0.1uF D51N4148 9 810 U34D MAT04 R2 62K R1 62K C7 100pF C6 100pF C89 47pF C8847pFD12822 D2 2822 6 75 U34CMAT04 13 1412 U34B MAT04 2 13 U34A MAT04 R774.7k C96 0.1uF R76 4.7k R83 120 R55 1k D81N4148 C55 0.1uF R89 200 R651.5k R87 1.2k R681.2k R86 1.2k R69 1.2k C72 100pF L7 BLM31PG391 +5V L8 BLM31PG391 R82 51 R54 1k R81 51 R744.7k R75 4.7k L12 8.2nH C2210nF L11 8.2nH C23 10nF R661.2K CHANNEL-SEL0 RF1 1 GND 2 RF2 3 VB 4 RFC 5 VA 6 U8SW-425 C1147pFC1247pF C13 47pF 1 J21PIN VA VB RF1RF2 2 4 U9TC7S04/E5 2 4 U10TC7S04/E5 RF IN C140.1uF +5V RF IN 1 J11PIN Vin 1 GND 2 +8V 3 U104 LM7809T 12V C2050.1uF C2060.1uF C204 100UF/16V L3 BLM31PG391 1 1 2 2 L2BLM31PG391 CLOCK 1 DATA 2 ENABLE 3 OSC IN 4 GND 6 VCCVCO 7 NC 8 RF OUT 9 NC 5 NC 10 RETECT 11 VCCCHI 12 U2PLL400-915 Vin 1 GND 2 +5V 3 U4 L78M05ACDT +5V C3060.1uF C3050.1uF Pin 1 Vapc 2 Vdd 3 Pout 4 U6PF01411A L4 BLM31PG391 L0 100nH 1 1 2 2 W 3 VR110K EN 1 IN 2 GND 3 OUT 4 ADJ 5 U3MIC29302 C30447pF C30347pF C302 47pF L1 BLM31PG391 +5V 13 2 4 T1 12.8MHz PLL-CLKPLL-DATAPLL-ENPOWER ON R5200R64.7K C31833pF C317 1.0nF C31010nF C3151.0nF C3160.1uF C1747pF C319220UF/10V C314 220UF/10V C308 2.2UF/16V C3072.2UF/16V C3010.1uF C313100pF D102.2V +5V ASK IN R81K B 1 C 2 E 3 U223904 9V C31147pF 9V RF OUT VCC RF IN 1 VCC 2 GND 3 GND 4 GC 5 GND 6 RFOUT 7 PD 8 U5RF2302 L2010nH +5V +5V +5V D202.7V C402 15pF C40312pF R17100 C40722pF C408 1.0nF C404 1nF C401 1.0uF C409 1.0uF C326220UF/10V C328 10nF R13 470 C4000.1uF +5V 123456789 101112131415 J0CON15 VCCVCCPLL-CLKPLL-DATAPLL-RDYCHANNEL-SEL1ASK-OUT012VPOWER ONASK INGNDPLL-ENCHANNEL-SEL2 CHANNEL-SEL0 ASK-OUT1 ASK-OUT0ASK-OUT1 TMS 1 TCK 2 TDI 3 TDO 4 /CS 5 CAL 6 ENSPI 7 GND 8 VREFOUT 9 IN- 10 IN+ 11 TEST 12 OUT_ 13 OUT+ 14 TEST 15 Vs 16 U37PAC80 TMS 1 TCK 2 TDI 3 TDO 4 /CS 5 CAL 6 ENSPI 7 GND 8 VREFOUT 9 IN- 10 IN+ 11 TEST 12 OUT_ 13 OUT+ 14 TEST 15 Vs 16 U38PAC80 TMS1 TDI1TDO1CAL1TCK1 ENSPI1 +5V L30 BLM21AH102SN1D C30 1uF +5V TMS2TCK2TDI2TDO2CAL2ENSPI2 +5V +5V L31 BLM21AH102SN1D C321uF C101uF R40 360 +5V Q303904 GND 1 RFI 2 GND 3 GND 6 RFO 5 GND 4 U11SF2049B R37 51 C311.0UF C33 1.0UF R9360 R74.7K +5V R304.7K R324.7K R334.7K R35 4.7K R195.1K GND 1 LO 2 GND 3 N.G 4 GND 8 RF 7 GND 6 IF 5 U7HMC207S8 C1547pF R1651 TMS 1 TCK 2 TDI 3 TDO 4 /CS 5 CAL 6 ENSPI 7 GND 8 VREFOUT 9 IN- 10 IN+ 11 TEST 12 OUT_ 13 OUT+ 14 TEST 15 Vs 16 U1PAC80 TMS0TCK0TDI0TDO0CAL0 ENSPI0 +5V L13 BLM21AH102SN1D C16 1uF +5V C18 1.0UF R114.7KR104.7K R14249 +5V R151k R12249 RFIN1 RFIN2 RFIN3 RFIN4 RFIN5 RFIN6RFIN7 XCRF-502C Reader Oscillator 1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA ASK_OUT0 C301 56pF C302 56pF C30356pF C30456pF C305 56pF C306 56pF C307 56pF C30856pF C309 56pF POWER_ONASK_INPLL_CLKPLL_DATAPLL_ENPLL_RDYCHANNEL_SEL0ASK_OUT1 P_RDYBACK0BACK1ANT_SEL0P_CLKD_OUTRFPOWER R311 100 R310 100 R309 100 R308 100 R307 100 R306 100 R305 100 R304 100 R303 100 LED_3LED_1LED_2 LED1LED2 L1011000 E11110uF/16V E10210uF/16V C1010.1uF R1041k R1021.2k C1120.1uF C1030.1uF E10310UF/16V E10447uF/16V R101680 3.3V L1021000 R1051k C1040.1uF C1050.1uF E10510uF/16V E10647uF/16V R106470 2.5V L1031000 VCC VCC R103470 R129680R126680R125680 P_DATAP_EN SPEAKER N_CSN_RD# N_WR#N_INT# R1191k R10710 LED_4LED_GF2N_CNTN_LINKLED_GF1 R3022680R3023680R3024330R3025330R3021680 LED3LED4 GND 3.3V XCRF-610-netXCRF-610W_NET_V10.sch N_ALE 1234 J001 XH5082-R-4P 12V L11.7mH L21.7mH L31.7mH L41.7mH E11000uF/16V 12 E21000uF/16V E31000uF/16V E41000uF/16V 5V C50.1uF C70.1uFC80.1uF C60.1uF 5V_RF12V_RF XCRF-502C Reader File: Time: page 1 total 2 Authorize wenyiqingStandardizationAuditor wenyiqingDesigner Liuchunjiang pcb: R128680 3.3V 5V 5V 5V 12V NC 1 GND 2 CLK 3 VCC 4 U203 OSC FRE=24MHz GND GND/RD/WRA0A1A2A3A4A5A6A7A8A9A10A11A12A13A14A15A16A17A18 D0D1D2D3D4D5D6D7 A0 12 A1 11 A2 10 A3 9 A4 8 A5 7 A6 6 A7 5 A8 27 A9 26 A10 23 A11 25 A12 4 A13 28 A14 29 A15 3 A16 2 A17 30 A18 1 DQ0 13 DQ1 14 DQ2 15 GND 16 CE 22 OE 24 WE 31 VCC 32 DQ3 17 DQ4 18 DQ5 19 DQ6 20 DQ7 21 U202AM29F040_PLC32 GNDVCC IO 1 NC 2 IO/GTS1 3 IO/GTS2 4 VCCIN 5 IO 6 NC 7 IO 8 IO 9 IO 10 IO 11 IO 12 IO 13 IO 14 IO 15 IO 16 IO 17 IO 18 NC 19 IO 20 GND 21 IO/GCK1 22 IO/GCK2 23 NC 24 IO 25 VCCIO 26 IO/GCK3 27 IO 28 IO 29 IO 30 GND 31 IO 32 IO 33 NC 34 IO 35 IO 36 IO 37 VCCIO 38 IO 39 IO 40 IO 42 NC 43 GND 44 TDI 45 NC 46 TMS 47 TCK 48 IO 49 IO 50 VCCIO 51 IO 52 IO 53 IO 54 IO 55 IO 56 VCCIN 57 IO 58 IO 59 IO 60 IO 61 GND 62 IO 63 IO 64 IO 65 IO 66 IO 67 IO 68 GND 69 IO 70 IO 71 IO 72 NC 73 IO 74 GND 75 IO 76 IO 77 IO 78 IO 79 NC 80 IO 81 IO 82 TDO 83 GND 84 IO 85 IO 86 IO 87 VCCIO 88 IO 89 IO 90 IO 91 IO 92 IO 93 IO 94 IO 95 IO 96 IO 97 VCCIN 98 IO/GSR 99 GND 100 IO 41 U201XC95144LVTQ100 D0D1D2D3D4D5 D6 D7A0A1A2A3A4A5A6A7A8A9A10A11A12A13A14A15A16A17A18/RD/WR 123456 J2026PIN 3.3VGND 3.3VGNDD_TDID_TMSD_TCKD_TDO D_TDID_TMSD_TCKD_TDO CCLK INITDONEDINPROGRAM F_TDOF_TCKF_TMSF_TDI F_TDOF_TCKF_TMSF_TDI 12345678 J2018PIN GNDD_EN D_EN R203 4.7k R202 4.7k R201 4.7k 3.3V INITDONED_EN 3.3V CLOCK C2040.1uF R204 68 C205 0.1uF 3.3V USER0USER1 3.3V 3.3V VCCO 1 TCK 2 I/O 3 I/O 4 I/O VREF 5 I/O 6 I/O 7 GND 8 VCCINT 9 I/O 10 I/O 11 I/O VREF 12 I/O 13 VCCINT 14 I,GCK3 15 V…

Text truncated - open the document above for the full version.

Shenzhen Huatongwei International Inspection Co., Ltd REPORT NO: WE06070008 FCC ID: TQ4YWGIT-R5678902 DATE: 08/11/2006 Page 1 Rev. 00 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Reader FCC ID:TQ4YWGIT-R5678902 MODEL No.: XCRF-502C BRAND NAME: N/A REPORT NO: WE06070008 ISSUE DATE: Aug 11, 2006 Prepared for INVENGO INFORMATION TECHNOLOGY CO., LTD. 3/F. NO. T2-B. HIGH-TECH INDUSTRIAL PARK SOUTH, SHENZHEN, CHINA Prepared by SHENZHEN HUATONGWEI INTERNATIONAL INSPECTION CO., LTD d.b.a. SHENZHEN HUATONGWEI INTERNATIONAL INSPECTION CO., LTD HUATONGWEI BUILDING, KEJI RD. 12 S., HIGH-TECH PARK, NANSHAN DISTRICT, SHENZHEN, GUANGDONG , P.R.CHINA TEL: 86-755-26748099 FAX: 86-755-26748089 Shenzhen Huatongwei International Inspection Co., Ltd REPORT NO: WE06070008 FCC ID: TQ4YWGIT-R5678902 DATE: 08/11/2006 Page 2 Rev. 00 VERIFICATION OF COMPLIANCE Applicant: Invengo Information Technology Co., LTD. 3/F. No. T2-B. High-Tech Industrial Park South, Shenzhen, China Manufacturer Invengo Information Technology Co., LTD. 3/F. No. T2-B. High-Tech Industrial Park South, Shenzhen, China Product Description: RFID Reader Brand Name: N/A Model Number: XCRF-502C Serial Number: N/A File Number: WE06070008 Date of Test: July 30, 2006 ~ Aug 07, 2006 We hereby certify that: The above equipment was tested by SHENZHEN HUA TONG WEI INTERNATIONAL INSPECTION CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003) and the energy emitted by the sample EUT tested as described in this report is in compliance with radiated emission limits of FCC Rules Part 15.247. The test results of this report relate only to the tested sample identified in this report. Approved By Reviewed By Jimmy Li / Executive Manager Tracy Qi / Testing Engineer SHENZHEN HUA TONG WEI SHENZHEN HUA TONG WEI INTERNATIONAL INSPECTION CO., LTD INTERNATIONAL INSPECTION CO., LTD Shenzhen Huatongwei International Inspection Co., Ltd REPORT NO: WE06070008 FCC ID: TQ4YWGIT-R5678902 DATE: 08/11/2006 Page 3 Rev. 00 Table of Contents 1. GENERAL INFORMATION................................................................................................ 4 1.1 Product Description ............................................................................................................................ 4 1.2 Related Submittal(s) / Grant (s)......................................................................................................... 4 1.3 Test Methodology ................................................................................................................................ 4 1.4 Test Facility ......................................................................................................................................... 4 2. SYSTEM TEST CONFIGURATION .................................................................................. 6 2.1 Configuration of Tested System......................................................................................................... 6 3. Summary of Test Result.........................................................................................................7 4. DESCRIPTION OF TEST MODES..................................................................................... 7 5. MEASUREMENT PARAMETERS ..................................................................................... 8 5.1 Conduction Emission .......................................................................................................................... 8 5.2 Hopping Channels............................................................................................................................. 10 5.3 Channel Separation........................................................................................................................... 12 5.4 20 dB Bandwidth ............................................................................................................................... 13 5.5 Operation Frequency ........................................................................................................................ 14 5.6 Peak Output Power ........................................................................................................................... 15 5.7 Spurious Emission at Transmitting Mode ...................................................................................... 18 5.8 Band Edge .......................................................................................................................................... 20 5.9 Spurious Emission at Receiving Mode ............................................................................................22 5.10 Dwell Time ......................................................................................................................................... 24 Shenzhen Huatongwei International Inspection Co., Ltd REPORT NO: WE06070008 FCC ID: TQ4YWGIT-R5678902 DATE: 08/11/2006 Page 4 Rev. 00 1 GENERAL INFORMATION 1.1 Product Description The EUT is an short range, lower power, RFID reader and writer designed as an “ Input Device”. It is designed by way of utilizing the FHSS technology to achieve the system operation. A major technical descriptions of EUT is described as following: A). Operation Frequency: Form 902 MHz – 928 MHz total 51 channels with 500 KHz intervals ( 902.5 MHz, 903.0 MHz,......, 927.5MHz ) B). Modulation: FHSS C). Antenna Designation: Dedicated Antenna with 6 dB Gain (Replace by end user is not permitted) D). Power Supply: AC 120 V/60 Hz 1.2 Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: TQ4YWGIT-R5678902 filing to comply with Section 15.247 of the FCC Part 15, Subpart C Rules. 1.3 Test Methodology Both conducted and radiated testing were performed according to the procedures i…

Text truncated - open the document above for the full version.

Shenzhen Huatongwei International Inspection Co., Ltd REPORT NO: WE0607 0008 FCC ID: TQ4YWGIT-R5678902 DATE: 08/11/2006 Page 27 Rev. 00 Conducted Emission Setup Photos Radiated Emission Setup Photos