TQ8-FOB-4F46Remote Keyless Entry

Manual for vehicle manufacturer Model name: FOB-4F46, FOB-4F47 OUTLINE1. How to use FOB-4F46, FOB-4F47 ‐ FOB-4F46, FOB-4F47 is a part of Remote Keyless System. ‐ This unit controls door lock/door unlock/panic/remote engine start-stop/tailgate open/panic wirelessly. 2. Introduction of Transmitter ( FOB-4F46, FOB-4F47 ) - FOB-4F46 and FOB-4F47 share same PCB but the number of button is different.‐ FOB-4F46 has 5 buttons. ‐ FOB-4F47 has 4 buttons. - Th ese unit s use the battery ‐ Frequency is 433.92MHz GENERAL DESCRIPTION PRIMARY FUNCTION ‐ Remote door lock/door unlock/panic/remote engine start-stop/tailgate open/panic ‐ Operating voltage: 3V DC ‐ Center freq.: 433.92MHz MANUAL1. LOCK Button If the LOCK button is pressed, then TRANSMITTER sends the LOCK data. 2. UNLOCK Button If the UNLOCK button is pressed, then TRANSMITTER sends the UNLOCK data. 3. HOLD Button If the HOLD button is pressed, then TRANSMITTER sends HOLD data. 4 . TAILGATE Button If the TAILGATE button is pressed, then TRANSMITTER sends TAILGATE data. 5 . PANIC Button If the PANIC button is pressed, then TRANSMITTER sends PANIC data. FCC/ISED NOTICE [FCC]This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to this device not explicitly approved by manuf actur er could avoid your authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC [ISED]This device contains licence ‐ ex empt tr ansmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence ‐ exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le pr ésent appar eil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipmen t complies with ISED ra diation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the ISED Cet appareil est conforme aux limites d'exposition aux rayonnements de l’ISDE pour un environnement non con t rôlé. L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur, à moins d'y être autorise par I'ISDE.

Hyundai MOBIS Co., Ltd. 203, Teheran-ro, Gangnam-gu, Seoul, 06141, Korea Tel. +82-31-260-2707, Fax. +82-31-899-1788 Letter of Declaration Product Equality We, Hyundai MOBIS Co., Ltd., as a manufacturer of following models, hereby declare that they have the following differences in supported features. _________________________ Seung Hoon Choe Representative Hyundai MOBIS Co., Ltd. Model NameDescription FOB-4F46Basic model FOB-4F47 Same as basic model, but the difference in the number of external buttons of the product.

Hyundai MOBIS Co., Ltd. 203, Teheran-ro, Gangnam-gu, Seoul, 06141, Korea Tel. 82-3 1-2 60-0 092 April 10, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 Request of Confidentiality for FCC ID: TQ8-FOB-4F46 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Hyundai MOBIS Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04- 1705. This provision will give Hyundai MOBIS Co., Ltd. temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: CONFIDENTIAL LIST Permanent 1 Block Diagram 2 Operational Descriptions 3 Schematics Short-Term 4 External Photos 5 Internal Photos 6 Test -Setup Photos 7 User ’s Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, __________________________ Seung Hoon Choe Senior Researcher Hyundai MOBIS Co., Ltd.

Hyundai MOBIS Co., Ltd. 203, Teheran‐ro, Gangnam‐gu, Seoul, 06141, Korea Tel. 82‐31‐260‐0092 April 10, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 Letter of Authorization We, Hyundai MOBIS Co., Ltd. hereby authorize SGS Korea Co., Ltd. (JOOHEE PARK, Hyuncahe You) to act on our behalf in all matters of certification. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti‐Drug Abuse Act of 1988, 21 U.S.C. 853(a). Any and all acts carried out by SGS Korea on our behalf shall have the same effect as acts of our own. This authorization is valid until further written notice. Sincerely, __________________________ Seung Hoon Choe Senior Researcher Hyundai MOBIS Co., Ltd.

External photos of EUT Top view of EUT Bottom view of EUT Side view of EUT

External photos of EUT Top view of EUT Bottom view of EUT Side view of EUT

Label Information FOB-4F46 LABEL MODEL: FOB-4F46 FCC ID: TQ8- FOB-4F46 IC: 5074A- FOB4F46 Inside battery compartment Label Label Position Hyundai MOBIS Co., Ltd. Label Information FOB-4F4 7 LABEL MODEL: FOB-4F4 7 FCC ID: TQ8- FOB-4F46 IC: 5074A- FOB4F46 Inside battery compartment Label Label Position Hyundai MOBIS Co., Ltd.

Internal photos of EUT Internal view of EUT Top view of Main PCB Bottom view of Main PCB View of Antenna PCB Pattern Antenna

Internal photos of EUT Internal view of EUT Top view of Main PCB Bottom view of Main PCB View of Antenna PCB Pattern Antenna

FCC ID: TQ8-FOB-4F46 According to KDB 447498 D01 General RF Exposure Guidance v06. At 100㎒to 6㎓ and for test separation distances ≤ 50 ㎜, the SAR test exclusion threshold is determined according to the following. [(max. power of channel, including tune-up tolerance,㎽) / (min. test separation distance,㎜)] x [√f(㎓)] ≤ 3.0 1. SAR test exclusion threshold Frequency: 433.92㎒(min. separation distances = 0㎜) Calculation value: 0.011 (㎽) / 5 (㎜) x √ 0.433 92 = 0.001 So, Calculation value ≤ 3.0 Remark; - Max. Radiated field strength 75.79 (㏈㎶ /m): Max. E.I.R.P. of EUT -19.44㏈m(0.011 ㎽) - When the minimum test separation distance is < 5㎜, a distance of 5㎜is applied to determine SAR test exclusion. 2. Conclusion: No SAR is required.

SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 Tel. +82 31 428 5700 / Fax. +82 31 427 2370 http://www.sgsgroup.kr Job Number:F690501-RF-RTL000525 Page:2of24 RTT5041-19(2020.03.02)(2) A4(210 mmx297 mm) INDEX Table of ContentsPage 1. General Information -----------------------------------------------------------------------3 2. Field Strength of Fundamental and Spurious Emission---------------------------6 3. Bandwidth of Operation Frequency----------------------------------------------------16 4. Occupied Bandwidth-----------------------------------------------------------------------18 5. Transmission Time--------------------------------------------------------------------------20 6. Duty Cycle Correction Factor------------------------------------------------------------22 7. Antenna Requirement----------------------------------------------------------------------24 SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 Tel. +82 31 428 5700 / Fax. +82 31 427 2370 http://www.sgsgroup.kr Job Number:F690501-RF-RTL000525 Page:3of24 RTT5041-19(2020.03.02)(2) A4(210 mmx297 mm) 1. General Information 1.1. Testing Laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) - 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 - 4, LS-ro 182beon-gil. Gunpo-si, Gyeonggi-do, Korea, 15807 - Designation number: KR0150 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible athttp://www.sgs.com/en/Terms-and-Conditions.aspx. Telephone:+82 31 688 0901 FAX:+82 31 688 0921 1.2. Details of Applicant Applicant:Hyundai Mobis Co., Ltd. Address:203, Teheran-ro, Gangnam-gu, Seoul, South Korea, 135-977 Contact Person:Choe, Seung-hoon Phone No.:+82 31 260 0098 1.3. Details of Manufacturer Company:Same as above Address:Same as above 1.4. Description of EUT Kind of Product FOB SMART KEY Model Name FOB-4F46 Variant Model Name FOB-4F47 Power Supply DC 3.0 V Frequency Range Tx: 433.92㎒, Rx: 125.00㎑ Modulation Type FSK Number of Channel 1 Antenna Type PCB Pattern Antenna 1.5. Information of Variant Models Model NameDescription FOB-4F46Basic model FOB-4F47 Same as basic model, but the difference in the number of external buttons of the product. SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 Tel. +82 31 428 5700 / Fax. +82 31 427 2370 http://www.sgsgroup.kr Job Number:F690501-RF-RTL000525 Page:4of24 RTT5041-19(2020.03.02)(2) A4(210 mmx297 mm) 1.6. Test Equipment List EquipmentManufacturerModelS/NCal. Date Cal. Interval Cal. Due Signal GeneratorR&SSMBV100A259067Jun. 10, 2019 Annual Jun. 10, 2020 Spectrum AnalyzerR&SFSV30103455 Dec. 22, 2019 Annual Dec. 22, 2020 Spectrum AnalyzerAgilentN9020AMY53421758Sep. 11, 2019AnnualSep. 11, 2020 PreamplifierH.P.8447F2944A03909Aug. 07, 2019AnnualAug. 07, 2020 Signal Conditioning Unit R&SSCU-1810117Jun. 12, 2019AnnualJun. 12, 2020 High Pass FilterMini-CircuitsNHP-800+V8207600724Mar. 04, 2020AnnualMar. 04, 2021 High Pass Filter Wainwright Instrument GmbH WHKX10-900-1000- 18000-40SS 7Mar. 04, 2020AnnualMar. 04, 2021 Loop Antenna Schwarzbeck Mess-Elektronik FMZB 15191519-039 Aug. 22, 2019 Biennial Aug. 22, 2021 Bilog Antenna Schwarzbeck Mess-Elektronik VULB9163396 Mar. 21, 2019 Biennial Mar. 21, 2021 Horn AntennaR&S HF906100326 Feb. 14, 2020 Annual Feb. 14, 2021 Test ReceiverR&SESU26100109 Feb. 18, 2020AnnualFeb. 18, 2021 Controller Innco systems GmbH CONTROLLER CO3000-4P CO3000/963/38 330516/L N.C.R.N/AN.C.R. Turn Table Innco systems GmbH DS 1200 SN/AN.C.R.N/AN.C.R. Antenna Master Innco systems GmbH MA4640-XP-ET MA4640/536/38 330516/L N.C.R.N/AN.C.R. Anechoic ChamberSY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/AN.C.R.N/AN.C.R. Coaxial CableSUCOFLEX104 (3 m)MY3258414Jan. 28, 2020 Semi- annual Jul. 28, 2020 Coaxial CableSUCOFLEX104 (10 m)MY3145814Jan. 28, 2020 Semi- annual Jul. 28, 2020 Coaxial Cable Rosenberger LA1-C006-1500 131014 01/20 Feb. 23, 2020 Semi- annual Aug. 23, 2020 SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 Tel. +82 31 428 5700 / Fax. +82 31 427 2370 http://www.sgsgroup.kr Job Number:F690501-RF-RTL000525 Page:5of24 RTT5041-19(2020.03.02)(2) A4(210 mmx297 mm) 1.7. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part15 subpart C, IC RSS-210 Issue 10 and RSS-Gen Issue 5 Section in FCCSection in ICTest Item(s)Result 15.209(a) 15.231(b) RSS-210 Issue 10 A.1, Table A1 RSS-Gen Issue 5 8.9 Radiated emission, Spurious Emission and Field Strength of Fundamental Complied 15.231(c)-Bandwidth of Operation FrequencyComplied 15.231(a) RSS-210 Issue 10 A.1.1 Transmission TimeComplied - RSS-210 Issue 10 A.1.3 RSS-Gen Issue 5 6.7 Occupied BandwidthComplied 15.207 RSS-Gen Issue 5 8.8 AC Power Line Conducted EmissionN/A 1) Note; 1) The AC power line test was not performed because the EUT use battery power for operation and which do not operate from the AC power lines. 1.8. Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the apparatus: ParameterUncertainty Occupied Bandwidth ±9.66㎑ Radiated Emission, 9㎑to 30㎒± 3.59㏈ Radiated Emission, below 1㎓± 5.88㏈ Radiated Emission, above 1㎓±5.94㏈ Uncertainty figures are valid to a confidence level of 95 %. 1.9. Test Report Revision RevisionReport NumberDate of IssueDescription 0F690501-RF-RTL0005252020.04.08Initial SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 Tel. +82 31 428 5700 / Fax. +82 31 427 2370 http://www.sgsgroup.kr Job Number:F690501-RF-RTL000525 Page:6of24 RTT5041-19(2020.03.02)(2) A4(210 mmx297 mm) 2. Field Strength of Fundamental and Spurious Emission 2.1. Test Setup The diagram below shows the test setup that is utilized to make the measurements for emission below 30 ㎒. The diagram below shows the test setup that is utilized to make the measurements for emission from 30㎒ to 1㎓. SG…

Text truncated - open the document above for the full version.

Test setup photos of EUT 1. Orthogonal plane of EUT - The testing was set in the three orthogonal planes and measured for each position (X, Y, Z). X-axis Y-axis Z-axis 2. Photo of Radiated Spurious Emission Test (Below 1㎓) 3. Photo of Radiated Spurious Emission Test (Above 1㎓)