TUNSKY-100REMOTE CONTROL TRANSMITTER

User Manual IPod RF receiver Set-up Plug the RF receive into the top of your iPod . The receiver will be run automatically in 30 seconds and your remote will be ready for operation at the same time. Plug in the 3.5MM head of the 3.5mm-to-RCA audio cable into your iPod and RCA end into your home studio, you are all set. You can start the freedom of the wireless control on your iPod up to 50 meter. Of course, you can plug your ear bud into receiver directly for portable use. The receiver is powered by your iPod, so no battery is needed. Our state-of-art low power design helps reducing the power consumption to the lowest level. Our default is if there is no music playing for 20 seconds, it will go to sleep mode to save power. There is a LED indicator on the receiver for voice recording feature. Compatible iPod: 3 rd /4 th GEN & Mini LED light up only for voice recording mode. When it is in voice recorder mode, the LED will be ON. Multi-function IPod Remote Control Basic Feature: Button 1: Next track (Forward) Button 5: Play & Pause Button 2: Last Track (Rewind) Button 6: Advanced Feature Button 3: Volume Up Button 7: Voice Recorder (press twice in two seconds to activate voice recording feature) Button 4: Volume Down LED: RED: voice record mode. GREEN: Others. Side switch is a hold switch. Advanced Feature: Next Playlist : Button 6 + button 1 Previous Playlist: Button 6 + Button 2 Next Album: Button 6 + + Previous Album: Button 6 + - Repeat one song : Button 6 + play, press again to repeat ALL. Press again to turn it off. Shuffle: press button 6 + button 7, press twice to turn it off. (Second button needs to be pressed within two seconds.) Built-in Voice Recorder (iPod only) When you plug the receiver into the iPod, there are two ways to record voice, or lecture. 1. Use your iPod’s menu: Go to “Extras” -> “Voice Memos” -> “Record Now” 2. Use remote: Press button 6 twice, you will see your iPod is in the voice recording mode already. Press start on your iPod to start recording. After recording, press save and playing on your ipod to save. Put the built-in microphone (in the receiver) near the speaker for the best performance. Note: For the best performance, Apple Inc. recommends to record with efficient power since low power will cause noise during the recording. Connecting to Car Stereo Using AUX input Most aftermarket stereo must have an available auxiliary RCA input. Follow the instructions to connect your iPod with your car speaker. 1. Disconnect negative battery terminal and remove aftermarket stereo. 2. Plug the RCA ends for the 3.5-to-RCA into the Left and Right auxiliary RCA INPUTS at the back of your aftermarket car stereo. 3. Reconnect negative battery terminal and power up your stereo. Verify that the iPod plays through your stereo when the Auxiliary input source is selected. Your stereo may require the CD Changer or Auxiliary Input to be activated in order to use. 4. Once test is complete and you hear the audio from your iPod through your vehicle’s stereo, re-install the stereo. 5. Locate the 3.5MM Male end of the 3.5-to-RCA cable in a dash packet or near your iPods location. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

A02 tx Block diagram MCU Transmitter TX SW-1~SW-7 LED

MAX LIGHT Technology Lab MAX LIGHT Technology Lab MAX LIGHT Technology Lab MAX LIGHT Technology Lab MAX LIGHT Technology Lab

Technology Lab Label Format: Label Position: Equipment Label 2.0cmX1.0cm Rear View Model No: sky-100 FCC ID: TUNSKY-100

MAX LIGHT Technology Lab MAX LIGHT Technology Lab MAX LIGHT Technology Lab MAX LIGHT Technology Lab MAX LIGHT Technology Lab

RF Remote Control for iPod and iPod mini Wireless remote control for your iPod.And, unlike IR based systems, Skyline’s remote uses RF technology, so it works around corners and through walls.Plus, it’s easy to setup, just plug the receiver cable into the top of the iPod, plug your speakers or headphone into the receiver module, and you are set!It works on your home stereo and your car stereo. Specifications Transmitter l6buttonkeyfob lplay/pause lnext track/ Fast Forward lPrevious Track / Rewind lVolume up lVolume Down lRange 50 Meter (typical lOperating Frequency : 433Mhz lSignal Indicator lNext Play list lPrevious Play list lNext Album lPrevious Album iPod Receiver lRequire no battery, use iPod for power lAdvanced power saving feature Package contents lKeyfob transmitter lRemote receiver lLithium Battery (CR2032) lUser’s guide lRCA/Speaker cable for users to connect to their existing stereo system at homeorinthecar. http://www.skylineconnect.com

A02 TX 1.0 7 CHANNEL A02 TX A 11 Monday, September 05, 2005 D:\WORK\CLPAN VISION\A02 FM RADIO\A02 TX-B.DSN TitleSize Document Number Rev Date: Sheet of VCC VCC VCCVCC VCC VCC VCC VCC ANT TX RB0 CH-3CH-4 CH-1 MCLR VCCU CH-5 SAW CH-7 CH-6 MCLRCH-1 RB0 ANT RED GREEN SW1 SWITCH,TS-A85BP-G 1 2 Q13356 2 31 C318P 12 R220K 1 2 C1nc 12 R110 1 2 C21.8P 12 L168nH 12 BT12032 12 R3100K 1 2 SW4 SWITCH,TS-A85BP-G 1 2 R4100K 1 2 SW3SWITCH 1 2 U1PIC 16F505 VDD 1 RB5/OSC1 2 RB4/OSC2 3 RB3/MCLR 4 RC5/T0CK1 5 RC4 6 RC3 7 RC2 8 RC1 9 RC0 10 RB2 11 RB1 12 RB0 13 VSS 14 C40.1uF 1 2 R8 100K 1 2 SW5SWITCH 1 2 D21SS400 1 2 R10100K 1 2 D41SS400 1 2 SW7SWITCH 1 2 SW6SWITCH 1 2 R111K 1 2 JP1HEADER 5 12345 R91K 1 2 SW8SWITCH 1 2 L30 12 L222nH 12 C5390 12 S1SW SPDT 2 1 3 D51SS400 12 D11SS400 12 X1 433.92MHZ/±75KHz 62 C7NC 12 C6NC 12 R7270 1 2 D3TRI COLOR LED 1 2 3

Product : Remote Control for I-Pod Applicant : Skyline Connectivity Corp. FCC ID : TUNSKY-100 Trade name : N/A Model : sky-100 Report No. : MLT0511P15001 Test Date : 11/22/2005 Test By Max Light Technology Co., Ltd. Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan., R.O.C. Tel: 886-2-363-2447 Fax: 886-2-363-2597 T T h h e e t t e e s s t t r r e e p p o o r r t t c c o o n n s s i i s s t t s s o o f f 2 2 9 9 p p a a g g e e s s i i n n t t o o t t a a l l . . I I t t m m a a y y b b e e d d u u p p l l i i c c a a t t e e d d c c o o m m p p l l e e t t e e l l y y f f o o r r l l e e g g a a l l u u s s e e w w i i t t h h t t h h e e a a l l l l o o w w a a n n c c e e o o f f t t h h e e a a p p p p l l i i c c a a n n t t . . I I t t s s h h a a l l l l n n o o t t b b e e r r e e p p r r o o d d u u c c e e d d e e x x c c e e p p t t i i n n f f u u l l l l , , w w i i t t h h o o u u t t t t h h e e w w r r i i t t t t e e n n a a p p p p r r o o v v a a l l o o f f o o u u r r l l a a b b o o r r a a t t o o r r y y . . MAX LIGHT MEASUREMENT REPORT Page: 2/29 Report Number: MLT0511P15001 FCC ID: TUNSKY-100 Technology Lab MAX LIGHT MEASUREMENT REPORT Page: 3/29 Report Number: MLT0511P15001 FCC ID: TUNSKY-100 Technology Lab CERTIFICATION We here by verify that : The test data, data evaluation, test procedures and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003. All test were conducted by MLT (Max Light Technology Co., Ltd) Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan, R.O.C Also, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report is in compliance with radiated emission limit of FCC Rules Part 15 Subpart C Section 15.231. EUT : Remote Control for I-Pod Applicant : Skyline Connectivity Corp. 4F, No.1. Alley 1. Lane 568, Zhoungshan S Rd, Yongkang City Tainan County 710 Taiwan R.O.C. Manufacturer : Skyline Connectivity Corp. 4F, No.1. Alley 1. Lane 568, Zhoungshan S Rd, Yongkang City Tainan County 710 Taiwan R.O.C. Model No : sky-100 FCC ID : TUNSKY-100 Approved by : Prepared by : Jesse Tien Roger Chen MAX LIGHT MEASUREMENT REPORT Page: 4/29 Report Number: MLT0511P15001 FCC ID: TUNSKY-100 Technology Lab 1.1 Introduction The following measurement report is submitted on behalf of Skyline Connectivity Corp. In support of an Intentional Periodic Radiator certification in accordance with Part 2 Subpart J and Part 15 Subpart A And C of the Commission’s and Regulations. 1.2 Description of EUT EUT : Remote Control for I-Pod Applicant : Skyline Connectivity Corp. 4F, No.1. Alley 1. Lane 568, Zhoungshan S Rd, Yongkang City Tainan County 710 Taiwan R.O.C Manufacturer : Skyline Connectivity Corp. 4F, No.1. Alley 1. Lane 568, Zhoungshan S Rd, Yongkang City Tainan County 710 Taiwan R.O.C Model No : sky-100 FCC ID : TUNSKY-100 Power Type : Powered by Battery 3Vdc(CR2032). The EUT(sky-100) is remote transmitter. The operation frequency is 433.92Mhz. Press the button on remote transmitter, can set the Last track/Next track/ Volume Up/Volume Down/Play& Pause/Voice Recorder button. MAX LIGHT MEASUREMENT REPORT Page: 5/29 Report Number: MLT0511P15001 FCC ID: TUNSKY-100 Technology Lab 1.3 Description of Support Equipment The EUT itself forms a system. No support equipment is required for its normal operation. 1.4 Configuration of System Under Test 1.7 Test Procedure All measurements contained in this report were performed according to the techniques described in Measurement procedure ANSI C63.4: 2003 "Measurement of Intentional Radiators." 1.8 General Test Condition The conditions under which the EUT operates were varied to determine their effect on the equipment's emission characteristics. The final configuration of the test system and the mode of operation used during these tests were chosen as that which produced the highest emission levels. However, only those conditions which the EUT was considered likely to encounter in normal use were investigated. EUT MAX LIGHT MEASUREMENT REPORT Page: 6/29 Report Number: MLT0511P15001 FCC ID: TUNSKY-100 Technology Lab The EUT operates solely by the battery. According to the rule of Section 15.207(c), the EUT exempt to the power line conducted test. MAX LIGHT MEASUREMENT REPORT Page: 7/29 Report Number: MLT0511P15001 FCC ID: TUNSKY-100 Technology Lab 3.1 General Configuration: Prior to open-field testing, the EUT was placed in a shielded enclosure and scanned at a close distance to determine its emission characteristics. The physical arrangement of the EUT was varied (within the scope of arrangements likely to be encountered in actual use) to determine the effect on the unit's emanations in amplitude, directivity, and frequency. The exact system configuration which produced the highest emissions was noted so it could be reproduced later during the open-field tests. This was done to ensure that the final measurements would demonstrate the worst-case interference potential of the EUT. 3.2 General Configuration: Final radiation measurements were made on a three-meter, open-field test site. The EUT system was placed on a nonconductive turn table which is 0.8 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 250 MHz to 2.5 GHz in order to cover the whole spectrum below 10th harmonic which could generate from the EUT. During the test, EUT was set to transmit continuously & Measurements spectrum range from 30 MHz to5 GHz is investigated. For measurements below 1 GHz the resolution bandwidth is set to 100 kHz for peak detection measurements or 120 kHz for quasi-peak detection measurements. Peak detection is used unless otherwise noted as quasi-peak. For measurements above 1 GHz the resolution bandwidth is set to 1 MHz, then the video bandwidth is set to 1 MHz for peak measurements and 10 Hz for average measurements. MAX LIGHT MEASUREMENT REPORT Page: 8/29 Report Number: MLT05…

Text truncated - open the document above for the full version.

MAX LIGHT MEASUREMENT REPORT Page: 10/29 Report Number: MLT0511P15001 FCC ID: TUNsky-100 Technology Lab 3.4 Test Configuration: Front View of The Test Configuration MAX LIGHT MEASUREMENT REPORT Page: 11/29 Report Number: MLT0511P15001 FCC ID: TUNsky-100 Technology Lab Rear View of The Test Configuration