TX4-RD98ABLE Remote Control

1. Pairing Method 1) To activate the pairing function the user will press any key. The amber LED begins to flash slowly for 30 seconds, the flash rate shall be 5 flashes every 3 seconds. 2) Local Name : TiVo_Remote 3) If the pairing is successful, the remote will flash the amber LED quickly 5 times. 4) If the remtoe has not successfully paired with a target after 20 complete cycles it will exit pairing mode and enter IR mode. 5) To activate the pairing function in IR mode, the user will press and hold the TiVo and Back key until the red LED remains on. If the pairing is unsuccessful the remote will return to its previous pairing state. 2. Global Reset (Unpair) The user can use the Global Reset command to reset all programmable keys and features to their original factory settings which and also un-pair Bluetooth. To perform the Global Reset command 1) Press and hold the TiVo and TV Pwr buttons simultaneously for 3 seconds until the red LED remains on. 2) Press Volume Down button 3 times and press the TiVo key. The red LED will blink 3 times and shut off. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Industry Canada Statement (For Canada) This device complies with Industry Canada’s licence-exempt RSS Stadard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Avis d'industrie canada Cet appareil est conforme aux normes CNR d’Industrie Canada applicables aux dispositifs exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC Radiation Exposure Statement (For Canada) This equipment complies with IC radiation exposure limits set forth for an Uncontrolled environment. RD98 Manual NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITYTO OPERATE THE EQUIPMENT.

Remote Solution Co., Ltd. 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Remote Solution Co., Ltd. Address: 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Product Name: BLE Remote Control FCC ID: TX4-RD98A Model(s): RD98, RD98XBB (X stands for A~Z, BB stands for 00~99) 2.911(d)(5)(i) Equipment Type We, [Remote Solution Co., Ltd.] certify that the equipment for which authorization is sought through certification is not: • Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules. • Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Byung-Cheol, Kim Date: February 27, 2023 Title and Company name: Manager, Remote Solution Co., Ltd. NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Remote Solution Co., Ltd. 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Remote Solution Co., Ltd. Address: 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Product Name: BLE Remote Control FCC ID: TX4-RD98A Model(s): RD98, RD98XBB (X stands for A~Z, BB stands for 00~99) 2.911(d)(5)(ii) Applicant filing We, [Remote Solution Co., Ltd.] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Byung-Cheol, Kim Date: February 27, 2023 Title and Company name: Manager / Remote Solution Co.,Ltd. NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Date: February 27, 2023 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: New Family Listing Declaration Please review the attached exhibits supporting our request for applying New Family Listing to the FCC ID: TX4-RD98A for Company Name: Remote Solution Co.,Ltd. Product Description: BLE Remote Control Base model: RD98 Additional model(s): RD98XBB (X stands for A~Z, BB stands for 00~99) The only difference between the basic model RD98 and the additional model(s) RD98XBB (X stands for A~Z, BB stands for 00~99) is as follows: Model Name Differences RD68A00 Basic Model RD98XBB (X stands for A~Z, BB stands for 00~99) Multiple models are derived for Marketing purpose, Each model name is made of RD98 and the combination of A~Z and 00~99. All multiple models are identical to the basic model except for model name. Note: Multiple model name RD98XBB is made up of a combination of X (A~Z) and BB (00~99) Should you have any questions, please contact us. Sincerely, Name: Byung-Cheol, Kim Title: Manager

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 27, 2023 Subject; Request for Confidentiality FCC ID: TX4-RD98A To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Byung-Cheol, Kim Title: Manager

Letter of Authorization Company: Remote Solution Co.,Ltd. Address: 92, Chogokri Nammyun, Kimchon City, Kyungbuk, 740-871, South Korea Product Name: BLE Remote Control Model Number: RD98, RD98XBB (X stands for A~Z, BB stands for 00~99) FCC Identifier: TX4-RD98A We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Byung-Cheol, Kim Date: February 27, 2023 Title: Manager Signature of applicant:

Page 1 / 7 External Photos Model name: RD98, RD98XBB (X stands for A~Z, BB stands for 00~99) Type of Equipment: BLE Remote Control FCC ID: TX4-RD98A Page 2 / 7 Page 3 / 7 Page 4 / 7 Page 5 / 7 Page 6 / 7 Page 7 / 7

Page 1 of 2 IDENTIFICATION LABEL: PROPOSED FCC ID LABEL The FCC ID shall be permanently affixed inside Battery case. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. Made in Korea FCC ID :TX4-RD98A Page 2 of 2 Authorized Person Print Name: Byung-Cheol, Kim Date: February 27, 2023 Signature:

Page 1 / 5 Internal Photos Model name: RD98, RD98XBB (X stands for A~Z, BB stands for 00~99) Type of Equipment: BLE Remote Control FCC ID: TX4-RD98A Page 2 / 5 Page 3 / 5 Page 4 / 5 Page 5 / 5 Chip Antenna

Page 1 of 6 Report No.: OT-231-RWD-035 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMF TEST REPORT Test Report No. : OT-231-RWD-035 Reception No. : 2301000018 Applicant : Remote Solution Co.,Ltd. Address : 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Manufacturer : Remote Solution Co.,Ltd. Address : 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Type of Equipment : BLE Remote Control FCC ID. : TX4-RD98A Model Name : RD98 Multiple Model Name : RD98XBB (X stands for A~Z, BB stands for 00~99) Serial number : N/A Total page of Report : 6 pages (including this page) Date of Incoming : January 05, 2023 Date of issue : January 31, 2023 SUMMARY The equipment complies with the regulation; FCC 47 CFR Part 1, 1.1310 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. This report is not correlated with the "KS Q ISO/IEC 17025 and KOLAS accreditation" of Korean Laboratory Accreditation Scheme. Tested by Soon-Ki, Choi / Engineer ONETECH Corp. Reviewed by Tae-Ho, Kim / General Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 6 Report No.: OT-231-RWD-035 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 4 2. GENERAL INFORMATION ............................................................................................................................................ 5 2.1 PRODUCT DESCRIPTION ................................................................................................................................................. 5 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 5 3. EUT MODIFICATIONS .................................................................................................................................................... 5 4. RF EXPOSURE EVALUATION ...................................................................................................................................... 6 4.1 RF EXPOSURE CALCULATION ....................................................................................................................................... 6 4.2 EUT DESCRIPTION ......................................................................................................................................................... 6 4.3 TEST RESULT ................................................................................................................................................................. 6 4.3.1 Test data for Bluetooth LE ..................................................................................................................................... 6 Page 3 of 6 Report No.: OT-231-RWD-035 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) Revision History Rev. No. Issue Report No. Issued Date Revisions Section Affected 0 OT-231-RWD-035 January 31, 2023 Initial Release All * Please contact us (e-mail: [email protected]) for verification of this test report. Page 4 of 6 Report No.: OT-231-RWD-035 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 1. VERIFICATION OF COMPLIANCE Applicant : Remote Solution Co.,Ltd. Address : 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Contact Person : Byung-Cheol Kim / Manager Telephone No. : +82-54-420-4517 FCC ID : TX4-RD98A Model Name : RD98 Brand Name : - Serial Number : N/A Date : January 31, 2023 EQUIPMENT CLASS DTS – DIGITAL TRNSMISSION SYSTEM E.U.T. DESCRIPTION BLE Remote Control THIS REPORT CONCERNS Original Grant MEASUREMENT PROCEDURES ANSI C63.10: 2020 TYPE OF EQUIPMENT TESTED Pre-Production KIND OF EQUIPMENT AUTHORIZATION REQUESTED Certification EQUIPMENT WILL BE OPERATED UNDER FCC RULES PART(S) FCC 47 CFR Part 1, 1.1310 Modifications on the Equipment to Achieve Compliance None Final Test was Conducted On 3 m, Semi Anechoic Chamber -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements. Page 5 of 6 Report No.: OT-231-RWD-035 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 2. GENERAL INFORMATION 2.1 Product Description The Remote Solution Co.,Ltd., Model RD98 (referred to as the EUT in this report) is a BLE Remote Control. The product specification described herein was obtained from product data sheet or user’s manual. DEVICE TYPE BLE Remote Control OPERATING FREQUENCY 2 402 MHz ~ 2 480 MHz MODULATION TYPE DSSS Modulation(GFSK) RF OUTPUT POWER 3.85 dBm NUMBER OF CHANNEL 40 Channel ANTENNA TYPE Chip Antenna ANTENNA GAIN 0.97 dBi Electrical Rating DC 3.0 V List of each Osc. or crystal Freq.(Freq. …

Text truncated - open the document above for the full version.

Page 1 of 33 Report No.: OT-231-RWD-036 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) RADIO PERFORMANCE TEST REPORT Test Report No. : OT-231-RWD-036 Reception No. : 2301000018 Applicant : Remote Solution Co., Ltd. Address : 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Manufacturer : Remote Solution Co., Ltd. Address : 92, Chogokri Nammyun, Kimchon City, Kyungbuk, Korea Type of Equipment : BLE Remote Control FCC ID. : TX4-RD98A Model Name : RD98 Multiple Model Name : RD98XBB (X stands for A~Z, BB stands for 00~99) Serial number : N/A Total page of Report : 33 pages (including this page) Date of Incoming : January 05, 2023 Date of issue : January 31, 2023 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. This report is not correlated with the "KS Q ISO/IEC 17025 and KOLAS accreditation" of Korean Laboratory Accreditation Scheme. Tested by Soon-Ki, Choi / Engineer ONETECH Corp. Reviewed by Tae-Ho, Kim / General Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 33 Report No.: OT-231-RWD-036 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 5 2. TEST SUMMARY .............................................................................................................................................................. 6 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 6 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS ........................................................................................... 6 2.3 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 6 2.4 PURPOSE OF THE TEST ................................................................................................................................................... 6 2.5 TEST METHODOLOGY .................................................................................................................................................... 6 2.6 TEST FACILITY ............................................................................................................................................................... 6 3. GENERAL INFORMATION ............................................................................................................................................ 7 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 7 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 7 4. EUT MODIFICATIONS .................................................................................................................................................... 7 5. SYSTEM TEST CONFIGURATION ............................................................................................................................... 8 5.1 JUSTIFICATION ............................................................................................................................................................... 8 5.2 PERIPHERAL EQUIPMENT .............................................................................................................................................. 8 5.3 MODE OF OPERATION DURING THE TEST ...................................................................................................................... 9 5.4 CONFIGURATION OF TEST SYSTEM ............................................................................................................................. 11 6. PRELIMINARY TEST .................................................................................................................................................... 11 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS ....................................................................................................... 11 6.2 GENERAL RADIATED EMISSIONS TESTS ..................................................................................................................... 11 7. MINIMUM 6 DB BANDWIDTH .................................................................................................................................... 12 7.1 OPERATING ENVIRONMENT ......................................................................................................................................... 12 7.2 TEST SET-UP ................................................................................................................................................................. 12 7.3 TEST DATE ................................................................................................................................................................... 12 7.4 TEST DATA FOR 1 MBPS ............................................................................................................................................... 13 8. MAXIMUM PEAK OUTPUT POWER ......................................................................…

Text truncated - open the document above for the full version.

品名 品名品名 品名： ：： ：ACA-3216-A1-CC-S History List 版本 版本版本 版本 REV. 修訂者 修訂者修訂者 修訂者 EDITOR 修訂頁次 修訂頁次修訂頁次 修訂頁次 PAGE 修訂內容 修訂內容修訂內容 修訂內容 ITEMS OF CHANGE 申請日期 申請日期申請日期 申請日期 DATE 生效日期 生效日期生效日期 生效日期 VALID DATE ECN編號 編號編號 編號 ECN NO. A0 林豪建 All 正式發行 2015/11/20 2015/11/23 N/A A1 林豪建 P2、3 修改Recommended PCB Layout 圖面 2016/06/23 2016/06/29 ECN20162620 UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT SPEC REV. TITLE： ：： ：ACA-3216-A1-CC-S Specification NO. ENS000069320 A1 PAGE 1 OF 8 - ACA-3216-A1-CC-S Specification 1. Features and Application： ：： ： This product is for WiFi/BT band 2. Explanation of Part Number： ：： ： AC A - 3216 - A1 - CC - S _ (1) (2) (3) (4) (5) (6) (7) (1) Product Type：Chip Antenna (2) Center Frequency/Band Code：2.4 GHz Band (3) Size Code：3.2*1.6 mm (Length * Width) (4) Design Revision Code：Rev.1 (5) Antenna Type ：Coupling Ceramics (6) Special Code：RoHS Compliant (7) Suffix For Special Requirements 3. Electrical Specification： ：： ： Item Specification Frequency Band 2400 ~ 2500 MHz Polarization Linear Impedance 50 ohm Typ. VSWR Less than 2.5 *Peak Gain 0.97 dBi Typ. *Peak Efficiency 71.1 % Typ. * Test condition：Test board size 100*50 mm Matching circuit may be required UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT SPEC REV. TITLE： ：： ：ACA-3216-A1-CC-S Specification NO. ENS000069320 A1 PAGE 2 OF 8 - 4. Physical Dimension： ：： ： Top view Bottom view Side view L 3.20 ± 0.30 W 1.70 ± 0.20 H 0.50 ± 0.10 A 0.30 ± 0.15 B 0.30 ± 0.15 L1 0.47 ± 0.20 W1 0.70 ± 0.20 (Unit：mm) 5. Recommended PCB Layout： ：： ： Layout H B A L W L1 W1 2.4 GHz Pad (GND) Pad (Feed) Feed Line (50 ohm) Pad (GND) Clearnace Area (8.5*6.5 mm) Ground UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT SPEC REV. TITLE： ：： ：ACA-3216-A1-CC-S Specification NO. ENS000069320 A1 PAGE 3 OF 8 - Pad Dimensions on PCB Layout Top View Perspective View (Unit：mm) * Tolerance ：±0.05 mm UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT SPEC REV. TITLE： ：： ：ACA-3216-A1-CC-S Specification NO. ENS000069320 A1 PAGE 4 OF 8 - 6. Electrical Characteristics： ：： ： Return Loss Frequency (MHz) VSWR 2400 1.84 2450 1.15 2500 1.99 Radiation Pattern： ：： ： The Gain pattern is measured in INPAQ’s FAR-field chamber. DUT is placed on the table of rotator, a standard horn antenna and Vector Network Analyzer is used to collect data. 3D Chamber Definition UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT SPEC REV. TITLE： ：： ：ACA-3216-A1-CC-S Specification NO. ENS000069320 A1 PAGE 5 OF 8 - 3D Gain Pattern 2450 MHz UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT SPEC REV. TITLE： ：： ：ACA-3216-A1-CC-S Specification NO. ENS000069320 A1 PAGE 6 OF 8 - 7. Taping Package and Label Marking： ：： ： (1) Quantity：4000pcs/Reel, T(Thickness of chip)≦1.2 (2) Plastic Tape Type W A B K t F P 3216 8±0.1 1.9~2.1 3.50~3.60 Max. 1.40 0.22±0.05 3.50±0.1 4.00±0.1 (Unit: mm) (3) Tape Packing (4) Cover Tape Reel Off Force (5) Reel Dimensions (Unit: mm) W A B 8±0.5 178±0.5 13±0.5 12±0.5 178±0.5 13±0.5 UNLESS OTHER SPECIFIED TOLERANCES ON： ：： ： X＝ ＝＝ ＝± ±± ± X.X＝ ＝＝ ＝± ±± ± X.XX＝ ＝＝ ＝ ANGLES＝ ＝＝ ＝± ±± ± HOLEDIA＝ ＝＝ ＝± ±± ± INPAQ TECHNOLOGY CO., LTD. SCALE： ：： ： ----- UNIT： ：： ：mm DRAWN BY:林豪建 林豪建林豪建 林豪建 CHECKED BY:吳柏青 吳柏青吳柏青 吳柏青 DESIGNED BY:林豪建 林豪建林豪建 林豪建 APPROVED BY:黃月碧 黃月碧黃月碧 黃月碧 THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USE…

Text truncated - open the document above for the full version.

Page 1 of 2 - Radiated Emission Test (Below 1 GHz) Page 2 of 2 - Radiated Emission Test (Above 1 GHz)