U2F60051101R4Open Wheel Chassis RC

Lift battery box straight up toremovefrom compartment. Remove old batteries and discard of properly. Install 4 fresh alkaline batteries following the polarity(+/-) indicated inside the battery compartment... RideSoundzTMInstallation Note to Adults Battery Performance Note Safety Tips Quick Tips Notes pour les adultes Afin d'assurer que le jouet de l'enfant est à la fois sûr et amusant, veuillez revoir toutes les instructions de montage et les règles de sécurité avec votre enfant. Pour tout problème avec le nouveau RIDEMAKERZ® RIDE, veuillez appeler la ligne gratuite de l'équipe RIDEMAKERZ ® 1-866-58-RIDEZ (74339) Renseignements sur la sécurité des piles La pile peut répandre des fluides qui peuvent endommager votre véhicule. Pour éviter la fuite de la pile: - Vous ne devez pas mélanger des piles anciennes avec des piles neuves ou des piles de différents types: alcaline, standard (carbone-zinc) ou des piles rechargeables (nickel- cadmium). - Comme indiqué, insérez les piles dans le compartiment intérieur des piles. - Retirez les piles avec une longue durée ou non utilisées. Retirez toujours les piles usées du véhicule. - Ne pas mettre les piles dans le feu, les piles peuvent exploser ou répandre des fluides. - Ne jamais provoquer un court-circuit des terminaux des piles. - Utilisez uniquement des piles identiques ou similaires à celles qui sont indiquées sur l'emballage, - Ne pas recharger des piles qui ne sont pas rechargeables. - Retirez les piles rechargeables du véhicule avant de les recharger. - Si vous utilisez des piles rechargeables, elles doivent être rechargées selon les instructions du fabricant et avec la supervision d'un adulte. Notes sur la performance des piles Pour une meilleure performance, utilisez des piles alcalines. La durée de vie des piles varie en fonction des marques. Installation des piles - Transmetteur et véhicule Retirez le compartiment des piles et placez la pile alcaline 9V suivant la polarité indiquée à l'intérieur du compartiment des piles. Replacez le couvercle du compartiment des piles et serrez convenablement les vis avec un tournevis (non inclus) Retirez le couvercle du compartiment des piles. Levez directement la boîte des piles pour la retirer du compartiment. Retirez les vieilles piles et éliminez-les de façon adéquate. Installez les 4 nouvelles piles alcalines suivant la polarité (+/-) indiquée à l'intérieur du compartiment des piles. Installez le paquet des piles Ni-Mh rechargeables (non inclus). Placez à nouveau le couvercle du compartiment des piles et serrez de façon adéquate la vis avec un tournevis ( non inclus) Installation du RideSoundzTM Insérez le RideSoundzTM la porte du châssis du véhicule et exercez de la pression avec fermeté jusqu'à ce que le RideSoundz TM soit totalement inséré dans le port. Le véhicule a 3 chaînes de fréquence. Veuillez, avant l'opération, confirmez si l'interrupteur de la chaîne se trouve dans la position correcte et coïncide avec la position de l'interrupteur de la chaîne du transmetteur. Le véhicule a 3 chaînes de fréquence. Veuillez, avant l'opération, confirmez si l'interrupteur de la chaîne se trouve dans la position correcte et coïncide avec la position de l'interrupteur de la chaîne du transmetteur. ON / OFF Veuillez confirmer que l'interrupteur est en position of lorsqu'il n'est pas utilisé. 1/2/3 SÉLECTION DES CHAÎNES 1/2/3 SÉLECTION DES CHAÎNES LEVIER Si la voiture ne fonctionne pas dans une ligne droite, ajustez l'angle avec ce levier Quelques conseils de sécurité: • N'utilisez jamais votre véhicule dans la rue, dans l'eau, le sable ou la neige, sur un gros tapis ou sous la pluie. Si votre véhicule est mouillé, ne l'utilisez pas jusqu'à ce qu'il sèche complètement. • Vous ne devez pas prendre le véhicule lorsque celui-ci est en mouvement. • Vous ne devez pas le placer auprès d'une source de chaleur ou en contact direct avec le soleil pendant une longue durée. • Vous ne devez pas utiliser le véhicule sur une table ou d'autres surfaces élevées. • Maintenez les doigts, les cheveux ou les vêtements amples hors de la portée des roues. • La supervision d'un adulte est conseillée lorsque la voiture est en marche. • Évitez d'envoyer le véhicule contre les objets. • Pour éviter des opérations accidentelles, laissez l'interrupteur de puissance en position off et retirez toutes les piles lorsque celui-ci n'est pas utilisé. Quelques conseils rapides • Lorsque le véhicule commence à perdre sa performance, sa puissance ou ses fonctions, il doit être temps de changer les piles. • L'interférence de la radio peut provoquer la lenteur de son fonctionnement. En cas d'interférence, vous devez utiliser le véhicule dans un autre local. • La performance de votre véhicule peut dépendre de la surface de conduite. • Élevez le transmetteur de l'antenne vers le haut, non pas trop vers le bas en direction du véhicule. Si le véhicule s'éloigne trop rapidement c'est parce que quelque chose est erroné. * Notes: Cet équipement a été testé et est en conformité avec les exigences du dispositif digital Classe B en accord avec la Partie 15 des règles du FCC. Ces limites sont conçues afin de proportionner une protection raisonnable contre les interférences préjudicielles dans une installation résidentielle. Cet équipement gère, utilise et peut irradier de l'énergie de radiofréquence et, s'il n'est pas installé et utilisé en accord avec les instructions, il peut causer des interférences préjudicielles aux communications radiophoniques. Néanmoins, il n'y a pas de garanties que l'interférence ne puisse survenir dans une installation particulière. Si cet équipement cause des interférences préjudicielles à la réception de la radio ou de la télévision, ce qui peut intervenir quand vous désactivez l'équipement, l'utilisateur est alors encouragé à essayer l'interface correcte avec une ou plusieurs des mesures qui suivent: - Réorientez ou replacez l'antenne réceptrice. - Augmentez l'espace entre l'équipement et le récepteur. - Connectez l'équipement…

Text truncated - open the document above for the full version.

1 1 1 1．SketchofthediagramoftheReceiver： Receiver with antenna U2 super-regenerator receiver U1amplify& decode Amplify/drivercircuitLeftmotor Rightmotor Motorfortransformer function 455kHzoscillation

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 RIDEMAKERZ, LLC. May 25 ,2011 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, RIDEMAKERZ, LLC. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product: Open wheel chassis RC Model: 526005 We affirm that between SIEMIC and RIDEMAKERZ, LLC. any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely,

SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 11 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 7.2 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 12 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 13 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 14 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 15 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 16 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 17 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 18 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 19 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if an…

Text truncated - open the document above for the full version.

Operation Operation Operation Operationdescription description description description(Remote (Remote (Remote (RemoteControl Control Control ControlCar) Car) Car) Car) 1.DrawingRef:RemoteControlCar(49.86MHzReceiver) U2SCRX8Aisa5functionalreceiveIC,itworkswithtransistorQ1,resistorR1andR2, capacitorC1,C2,C3,C4,C10,coilT1andinductanceL1,componentscombinedasRFreceive circuit.TheU2SCRX8Apin6,7,10and11outputcontrolsignals.TheQ8,Q9,Q10,Q11,Q12, Q13,Q14,Q15,Q16,Q17,Q18,Q19tocompriseamotordrivecircuitandcomponentsleft forwardandbackwardfunction. .Energyissupplywitha4.5-voltbattery.

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle Section, Science & Technology Park, District Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.:SZEM110500019202 Page: 1 of 19 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page FCC Test Report Application No.: SZEM1105000192RF Applicant: RIDEMAKERZ, LLC Address of Applicant: 111 PACIFIC, SUITE 110 IRVINE, CA 92618 Manufacturer/Factory: WIN BRIGHT MANUFACTURING LTD. Address of Manufacturer/ Factory: Foreign Economic District ,shang Lin Chun,Heng li Zhen, Dongguan Equipment Under Test (EUT): EUT Name: Open wheel chassis RC Model No.: 526005 FCC ID: U2F60051101R4 Standards: FCC PART 15, SUBPART B: 2010 Date of Receipt: 2011-05-11 Date of Test: 2011-05-11 Date of Issue: 2011-05-24 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. This report supersedes our previous report SZEM110500019201, issued on 2011-05-16, which is hereby deemed null and void. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 2 of 19 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 2 Test Summary Test Test Requirement Test Method Class / Severity Result Radiated Emission (30MHz to 1GHz) FCC PART 15, SUBPART B: 2010 ANSI C63.4: 2009 Class B PASS SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 3 of 19 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 3 Contents Page 1 COVER PAGE ............…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM110500019202 Page: 10 of 20 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 7 Photographs(Test Model No.: 526005) 7.1 Radiated Emission Test Setup