U4O8811960ADual Band Cellular Amplifier

MODEL 8811960A WIRELESS DUAL BAND AMPLIFIER OPERATIONAL MANUAL Note No professional installation assistance is required to properly install this unit I. Parts List Description Qty. o Amplifier/Antenna unit 1 II. Installation Instructions o Step 1. Place the Magnetic Antenna on the external part of the car on the roof or trunk as shown below. Try to have the antenna as far away as possible from where you will plug the unit in the cigarette lighter plug. o Step 2. Route the cable Route the 15 feet of cable, hiding it whenever possible to keep it out of the way. Run the cable up to the front of the car near the cigarette lighter plug for power. Note The 12-Volt source that is providing power may not turn off when you turn your car off. If this is the case in your car then unplug the unit when vehicle is turned off - or battery will drain, after a few days. o Step 3. Plug in the Amplifier unit Plug in the Amplifier unit into the cigarette plug and turn the car on, the green LED should turn on. Look at the bars on your phone as you plug the unit in Put your phone a few inches away from the Amplifier unit, you should see your bars go up after around 10 seconds; you are now ready to use your phone with enhanced performance. Important o Antenna must first be placed outside the car before you plug the amplifier into the cigarette lighter plug. Important The amplifier needs to be installed at least 20 cm (or approximately 8-in) away from all persons during normal operation to comply with the FCC’s radiofrequency radiation exposure requirement.

Tuesday, March 20, 2007 Elite Electronic Engineering, Inc. TCB Certification Services 1516 Centre Circle Downers Grove IL 60515 Attn: Daniel Crowder FCC/Certification Department Group Leader Gentlemen, 3XA Wireless Inc. is submitting application for equipment authorization for the Wireless Dual Band Amplifier, FCC ID: U408811960A under rule parts 22 & 24. This equipment is used to increase receive signal strength and reduced number of dropped calls in a car. It operates in the 800MHz and the 1900MHz band and covers AMP, GSM, TDMA and CDMA. Power Output Band Frequency Modulation dBm W Emission Designator AMP 12 0.015 D1F GSM 12 0.015 GXW TDMA 12 0.015 DXW 800MHz 869 - 894 MHz (downlink) CDMA 12 0.015 F9W AMP 12 0.015 D1F GSM 12 0.015 GXW TDMA 12 0.015 DXW 1900MHz1930-1990 MHz (downlink) CDMA 12 0.015 F9W We request that the following exhibits to be held confidential and withheld from public inspection. They are 3XA Wireless Inc. confidential proprietary information and are not normally released to the public. 1. Block Diagrams 2. Operational Description 3. Parts List 4. Schematic If you have any questions regarding this filing, please contact me at: Phil Aseltine VP and Director of Research and Development 3XA Wireless Inc. 990 Lutter Drive Suite B Crystal Lake, IL 60014 815 455 5466 Cell 847 772 7905

3XA Wireless Dual Band Amplifier Pictures External Product, Front External Product, Back FCC Label Location Internal Board, Front Internal Board, Back Internal Board, Back Internal Board, Front

NOTES: (UNLESS OTHERWISE SPECIFIED)1. MATERIAL: THERMAL WHITE POLYESTER .002 THICK OR EQUIVALENT.2. ADHESIVE: PERMANENT 350. 3. ALL NUMBERS TO BE SERIALIZED. ALPHA CHARACTERS ARE NOT TO BE CHANGED.4. BAR CODE SHALL CONFORM TO STANDARD 128. .250 .500 Crystal Lake, IL 60014 A B 3 C 3 22 DATE SIZE: APPROVED BY: CHECKED BY: DRAWN BY: 3/26/07 OF THE INFORMATION CONTAINED HEREIN, WHOLE OR IN PART WITHOUT THE EXPRESSED WRITTEN 0.005 X.XXX = 0.01 X.XX = 0.1 DATE: X.X = .003 DIA. = DWG NO.: 1 SHEET: REV REVISIONS DESCRIPTION 1 A OF REV: B C APPROVED TITLE: TOLERANCES UNLESS OTHERWISE SPECIFIED 1 0.0025 DATE: DATE: X.XXXX = UNITS ARE IN INCHES 1 1 ECN/CAR NO. SPECFIED DRAWINGUNLESS OTHERWISE ANGLE = PERMISSION OF 3XA WIRELESS, INC. IS STRICTLY PROHIBITED. 1 LBL100 B LABEL, FCC, IC, SN, MINI RJA THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROPRIETARY AND THE SOLE PROPERTY OF 3XA WIRELESS, INC. ANY UNAUTHORIZED USE, DUPLICATION, PUBLICATION, OR DISTRIBUTION 990 Lutter Dr. 3XA Wireless, Inc.

3XA Wireless Dual Band Amplifier Pictures External Product, Front External Product, Back FCC Label Location Internal Board, Front Internal Board, Back Internal Board, Back Internal Board, Front

TUNEUP PROCEDURE The Wireless Dual Band Amplifier requires no manual tuning. All parameters are factory set and controlled by a microprocessor.

Page 1 of 38 Engineering Test Report No. 38049-01 Measurement of RF Emissions from a Dualband Wireless Amplifier Model 8811960A For : 3XA Wireless Inc. Crystal Lake, IL P.O. No. : 3XA031507 Date Received : March 20, 2007 Date Tested : March 20 through March 29, 2007 Test Personnel : Richard E. King Specification : FCC "Code of Federal Regulations” Title 47 Part 22; RSS-132- Cellular Telephones Employing New Technologies Operating in the Bands 824- 849 MHz and 869-894 MHz Issue 2 September 2005 Test Report By : Richard E. King EMC Engineer Witnessed by : Phil Aseltine 3XA Wireless Inc. Approved By : Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 38049-01 THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 38 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. 1.0 INTRODUCTION............................................................................................................................................... 4 1.1 DESCRIPTION OF TEST ITEM.................................................................................................................. 4 1.2 PURPOSE..................................................................................................................................................... 4 1.3 DEVIATIONS, ADDITIONS AND EXCLUSIONS...................................................................................... 4 1.4 APPLICABLE DOCUMENTS...................................................................................................................... 4 1.5 SUBCONTRACTOR IDENTIFICATION..................................................................................................... 4 1.6 LABORATORY CONDITIONS.................................................................................................................... 5 2.0 TEST ITEM SETUP AND OPERATION......................................................................................................... 5 2.1 POWER INPUT............................................................................................................................................ 5 2.2 GROUNDING................................................................................................................................................ 5 2.3 PERIPHERAL EQUIPMENT....................................................................................................................... 5 2.4 MODULATION.............................................................................................................................................. 5 2.5 FREQUENCY SELECTION........................................................................................................................ 5 2.6 RF POWER OUTPUT.................................................................................................................................. 5 3.0 TEST EQUIPMENT.......................................................................................................................................... 6 3.1 TEST EQUIPMENT LIST............................................................................................................................ 6 3.2 CALIBRATION TRACEABILITY................................................................................................................. 6 4.0 REQUIREMENTS, PROCEDURES AND RESULTS................................................................................... 6 4.1 RF POWER OUTPUT MEASUREMENTS................................................................................................ 6 4.1.1 REQUIREMENTS................................................................................................................................. 6 4.1.2 PROCEDURES..................................................................................................................................... 6 4.1.3 RESULTS.............................................................................................................................................. 6 4.2 OCCUPIED BANDWIDTH MEASUREMENTS......................................................................................... 7 4.2.1 REQUIREMENTS................................................................................................................................. 7 4.2.2 PROCEDURES..................................................................................................................................... 7 4.2.3 RESULTS.............................................................................................................................................. 8 4.3 SPURIOUS EMISSIONS AT ANTENNA TERMINAL............................................................................... 8 4.3.1 REQUIREMENTS................................................................................................................................. 8 4.3.2 PROCEDURES..................................................................................................................................... 8 4.3.3 RESULTS.............................................................................................................................................. 9 4.4 FIELD STRENGTH OF SPURIOUS EMISSIONS.................................................................................... 9 4.4.1 REQUIREMENTS................................................................................................................................. 9 4.4.2 PROCEDURES..................................................................................................................................... 9 4.4.3 RESULTS...............................................................................…

Text truncated - open the document above for the full version.

Page 1 of 70 Engineering Test Report No. 38049-02 Measurement of RF Emissions from a Dualband Wireless Amplifier, Model No. 8811960A For : 3XA Wireless Inc. Crystal Lake, IL P.O. No. : 3XA031507 Date Received : March 20, 2007 Date Tested : March 20 through March 29., 2007 Test Personnel : Richard E. King EMC Engineer Specification : FCC CFR Title 47 Part 24; RSS-133 - 2 GHz Personal Communications Services Issue 3 June 2005 Test Report By : Richard E. King EMC Engineer Witnessed by : Phil Aseltine 3XA Wireless Inc. Approved By : Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 38049-02 THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 70 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. 1.0 INTRODUCTION...................................................................................................................................... 5 1.1 DESCRIPTION OF TEST ITEM .......................................................................................................... 5 1.2 PURPOSE .......................................................................................................................................... 5 1.3 DEVIATIONS, ADDITIONS AND EXCLUSIONS................................................................................. 5 1.4 APPLICABLE DOCUMENTS.............................................................................................................. 5 1.5 SUBCONTRACTOR IDENTIFICATION ..............................................................................................6 1.6 LABORATORY CONDITIONS ............................................................................................................ 6 2.0 TEST ITEM SETUP AND OPERATION................................................................................................... 6 2.1 POWER INPUT .................................................................................................................................. 6 2.2 GROUNDING..................................................................................................................................... 6 2.3 PERIPHERAL EQUIPMENT ............................................................................................................... 6 2.4 MODULATION.................................................................................................................................... 6 2.5 FREQUENCY SELECTION ................................................................................................................ 6 2.6 RF POWER OUTPUT......................................................................................................................... 7 3.0 TEST EQUIPMENT................................................................................................................................. 8 3.1 TEST EQUIPMENT LIST .................................................................................................................... 8 3.2 CALIBRATION TRACEABILITY.......................................................................................................... 8 4.0 REQUIREMENTS, PROCEDURES AND RESULTS............................................................................... 8 4.1 RF POWER OUTPUT MEASUREMENTS .......................................................................................... 8 4.1.1 REQUIREMENTS........................................................................................................................ 8 4.1.2 PROCEDURES........................................................................................................................... 8 4.1.3 RESULTS.................................................................................................................................... 8 4.2 OCCUPIED BANDWIDTH MEASUREMENTS.................................................................................... 8 4.2.1 REQUIREMENTS........................................................................................................................ 8 4.2.2 PROCEDURES........................................................................................................................... 9 4.2.3 RESULTS.................................................................................................................................... 9 4.3 SPURIOUS EMISSIONS AT ANTENNA TERMINAL.......................................................................... 9 4.3.1 REQUIREMENTS........................................................................................................................ 9 4.3.2 PROCEDURES......................................................................................................................... 10 4.3.3 RESULTS.................................................................................................................................. 10 4.4 FIELD STRENGTH OF SPURIOUS EMISSIONS............................................................................. 10 4.4.1 PRELIMINARY RADIATED MEASUREMENTS......................................................................... 10 4.4.1.1 REQUIREMENTS .............................................................................................................. 10 4.4.1.2 PROCEDURES.................................................................................................................. 11 4.4.1.3 RESULTS........................................................................................................................... 11 4.4.2 FINAL RADIATED EMISSIONS................................................................................................. 11 4.4.2.1 REQUIREMENTS .................................…

Text truncated - open the document above for the full version.