U8KVT15SCS-Band 2W Analog FM Video Transmitter

VT15/OM Rev-A Operation Manual VT15 Series UHF, L, S, C-Band Video / Audio Transmitters Designed and Manufactured By 2465 Old Hwy 40W, Ste. A Verdi, NV 89439 Distributed By 107 Woodbine Down Blvd, Units 7&8 Toronto, ON M9W 6Y1 VT15/OM Rev-A TABLE OF CONTENTS 1.0 Introduction..............................................................................................................1 1.1 Purpose and Function...................................................................................1 1.2 Capabilities ..................................................................................................1 1.3 Specifications ...............................................................................................2 1.4 Mechanical Drawing and Connector Pin-Outs ............................................4 1.5 List of Items Furnished ................................................................................5 1.6 List of Items Required .................................................................................5 1.7 Environmental Requirements.......................................................................5 2.0 Safety Precautions....................................................................................................5 3.0 Preparation for Use ..................................................................................................6 3.1 Unpacking ....................................................................................................6 3.2 Pre-Test ........................................................................................................7 4.0 Installation and Operating Instructions ....................................................................7 4.1 Use and Function of Connectors..................................................................7 4.2 Use and Function of Switches......................................................................8 4.2.1 Frequency Selection Switches .....................................................................8 4.2.2 Dual Power Switch ......................................................................................8 4.2.3 Video Inversion Switch................................................................................9 4.2.4 Audio On/Off Switch (250 mW Models Only) ...........................................9 4.2.5 Line / Mic Audio Level Switch (250 mW Models Only) ............................9 4.3 Use of Heat Sink ........................................................................................10 4.4 Initial Adjustments and Settings ................................................................10 4.5 Shut Down .................................................................................................10 5.0 Maintenance Instructions .......................................................................................10 5.1 Cleaning .....................................................................................................10 5.2 Troubleshooting .........................................................................................10 5.3 Preparation for Reshipment .......................................................................11 5.4 Returning an Item ......................................................................................11 Warranty Statement ...........................................................................................................12 Appendix A (Calculation of Safe Personal Distance from Antenna) ................................13 VT15/OM Rev-A 1 1.0 INTRODUCTION Thank you for choosing this AMP Wireless Video Product. Every effort has been made to design and manufacture a quality product that will meet your surveillance needs for many years. Please visit our website (www.advmw.com/video ) for information on other video products and for downloadable datasheets, operation manuals, and frequency selection charts. If you have any questions regarding this product or if you require technical assistance, please feel free to contact us at the telephone numbers below: Dyplex Communications Advanced Microwave Products (416) 675-2002 (775) 345-9933 1.1 Purpose and Function VT15 Series Video/Audio Transmitters are developed and manufactured by Advanced Microwave Products (AMP) and distributed by Dyplex Communications (Dyplex). Transmitters are designed for color or monochrome video and audio surveillance. Transmitters are best operated with AMP’s VR75 Series Video Receivers but are compatible with most other video receivers on the market. 1.2 Capabilities AMP Transmitters are designed for harsh environments and feature robust packaging and connectors. Compact package sizes provide versatility in unit placement and system applications. AMP Transmitters require no tuning or adjustments. All units operate directly with any standard video camera. Power requirements are +9 to +16 Vdc and can be derived from batteries, simple power supplies, or vehicle power. Whip or “rubber duck” antennas are adequate for most transmitter applications. A variety of standard and high performance antennas are available through Dyplex. AMP Transmitters and Receivers are standard equipped with video inversion, selectable via a slide switch, for a basic level of security. VT15 Series Transmitters are available with many options allowing customization to specific applications. Most common options include frequency selection (full band selection), high RF output power (up to 2 Watts), dual power operation (any two power levels), PAL video, and one Line / Mic level selectable audio subcarrier or two Line-Only audio subcarriers. Audio subcarriers are only available on 250 mW VT15 Series models. If our standard products and options do not satisfy your requirements, please contact us. Our experienced design team welcomes your custom specifications. VT15/OM Rev-A 2 1.3 Specifications RF Characteristics Frequency Range (Specify): UHF 340.00 - 399.90 MHz …

Text truncated - open the document above for the full version.

From: Roland Gubisch ES-BOX Sent: Friday, April 27, 2007 4:28 PM To: David Chernomordik ES-MPK Cc: Terre Wolak ES-ATL Subject: Advanced Microwave Products FCC ID: U8KVT15C, U8KVT30SC, U8KVT50SC Attachments: BMS RF safety information.pdf; Advanced Microwave Grant notes.doc David, Review of these three applications for video transmitters is complete, and the following points are noted for all applications: ADMINISTRATIVE (1) Each confidentiality request should reference only one FCC ID. Please provide 3 separate requests, one for each application. TECHNICAL (1) These transmitters have sufficient RF output to require user precautions in the operating manual. For example, the field from a dipole antenna attached to the 5W transmitter exceeds the MPE limit in 1.1310 at distances smaller than 25 cm from the antenna. Use of a higher-gain antenna would require larger separation dstances and adequate installation and user guidance. There is no such guidance presently in the operating manual. Please provide an RF exposure evaluation for each transmitter, and update the operating manuals with the equivalent guidance. A sample is attached, taken from a filing for a transmitter operating in the same frequency band and at similar RF power. A draft Grant Note is also attached, which references the material to be added. Certification can proceed as soon as these issues are addressed. Thank you, Roland

Model: VT15SC7NN Description: External photo showing connectors, user-controlled switches, and ID label

VT15SC Label location

Model: VT15SC7NN Description: Internal photo showing PCB VT15LS PLL-8SNN top side (double sided PCB), PCB VT15LS PA-S27 top side (single sided PCB), wiring, and connector interfaces. Model: VT15SC7NN Description: Photo of PCB VT15LS PLL-8SNN bottom side (top side shown internal photo above).

VT15 PA Created/Date: BL/070216 Advanced Microwave Products QC/Apvd/Date: BL/070313Verdi, NV 89439 Rev By/Date: BL/070313VT15LS Power Amplifier Rev Level: ABase BOM Item Reference Designato r P/NDescManufacturer Qty 1 PCB1 VT15LS PA Rev-APCB, VT15LS PA, Rev-A..LANmark1 2 R1,9,11 MCR03J180Res, 0603, 18 ohm, 5%Rohm3 3 R2,3,8 MCR03J222Res, 0603, 2.2k ohm, 5%Rohm3 4 R4,5 MCR03J471Res, 0603, 470 ohm, 5%Rohm2 5 R7 MCR18J151Res, 1206, 150 ohm, 5%Rohm1 6 R22 MCR03J104Res, 0603, 100k ohm, 5%Rohm1 7 R10,28,31 MCR03J560Res, 0603, 56 ohm, 5%Rohm3 8 C1,8,11,16,36,37 C0603C103M3RAC Cap, 0603, Ceramic, 10 nF, 20%, 25V, X7R..Kemet 6 9 C2,5,7,10,15,18,19,24,28,3 0,35,39,40 C0603C150J5GAC Cap, 0603, Ceramic, 15 pF, 5%, 50V, NPO..Kemet 13 10 C3,6 C0603C104M3RAC Cap, 0603, Ceramic, 100 nF, 20%, 25V, X7R..Kemet 2 11 C4,9,17,38 T491A106M016Cap, A-Case, Tant, 10uF, 16V, 20%Kemet 4 12 C12,34 278M6301106KCap, 0805, Tant, 10uF, 6.3V, 10%, MatsuoMatsuo2 13 C29,31-33 EMK107BJ105KACap, 0603, Ceramic, 1 uF, 10%, 16V, X5RTaiyo Yuden4 14 L1 ELJRER10JF2Ind, 0603, 100nH, 5%Panasonic1 15 FB1 BLM21P331SN1BFerrite Bead, 0805, 330 Ohm, 1.5A, MurataMurata1 16 Q1 AT-42035Transistor, NPN, RF, 6 GHz, Micro-X, Agilent..Agilent1 17 U1 MIC5213-5.0BC5IC, Regulator, LDO, 5.0V, 80mA, SC-70, Micrel..Micrel1 18 U3 MAX881REUBIC, Neg. Generator, -4V, 10-uMAX, MAXIMMAXIM1 19 J1 A-1JA-CRConnector, Coax, RF, 3mm SMT, AmphenolAmphenol1 789175.XLS

VT15LS PLL Created/Date: BL/070217 Advanced Microwave Products QC/Apvd/Date: BL/070217Verdi, NV 89439 Rev By/Date: N/AVT15LS Video PLL Rev Level: ABase BOM Item Reference Designator P/NDescManufacturer Qty 1 PCB1 VT15LS PLL Rev-APCB, VT15LS PLL, Rev-A..LANmark1 2 R1,33 MCR03J471Res, 0603, 470 ohms, 5%Rohm2 3 R2,14,20,31 MCR03J223Res, 0603, 22k ohms, 5%Rohm4 4 R3 MCR03J102Res, 0603, 1k ohm, 5%Rohm1 5 R4 MCR03F5361Res, 0603, 5.36k ohms, 1%Rohm1 6 R5 MCR18J470Res, 1206, 47 ohms, 5%Rohm1 7 R10 MCR03J301Res, 0603, 300 ohms, 5%Rohm1 8 R11 G32BTB101MPot, 3mm, 100 Ohm, 20%, Tocos..Tocos 1 9 R12,16 MCR03J912Res, 0603, 9.1k ohms, 5%Rohm2 10 R13,18,32,44 MCR03J103Res, 0603, 33k ohms, 5%Rohm4 11 R15 MCR03J333Res, 0603, 10k ohms, 5%Rohm1 12 R17,30 MCR03J472Res, 0603, 4.7k ohms, 5%Rohm2 13 R19,26,34,42,43 MCR03J220Res, 0603, 22 ohms, 5%Rohm5 14 R21,22 MCR03J391Res, 0603, 390 ohms, 5%Rohm2 15 R23,25 MCR03J222Res, 0603, 2.2k ohms, 5%Rohm2 16 R27,36-39 MCR03J105Res, 0603, 1M ohms, 5%Rohm5 17 R28,29 MCR03J104Res, 0603, 100k ohms, 5%Rohm2 18 R40,41 MCR03J683Res, 0603, 68k ohms, 5%Rohm2 19 R45 MCR03J106Res, 0603, 10M ohms, 5%Rohm1 20 C1,3,6,10,23,24,34,44,47 C0603C104M3RACCap, 0603, Ceramic, 100 nF, 20%, 25V, X7R..Kemet 9 21 C2 T491A106M016Cap, A-Case, Tant, 10uF, 16V, 20%Kemet 1 22 C4,7,20,22,25,33,35,36,45 C0603C102M3RACCap, 0603, Ceramic, 1nF, 20%, 25V, X7R..Kemet 9 23 C5,9,12,17,26,27 T491A226M010Cap, A-Case, Tant, 22uF, 10V, 20%..Kemet 6 24 C11,43 C0603C103M3RACCap, 0603, Ceramic, 10 nF, 20%, 25V, X7R..Kemet 2 25 C19,21,32,46 C0603C100J5GACCap, 0603, Ceramic, 10pF, 5%, 50V, NPO..Kemet 4 26 C28,39,42 278M1602105KCap, 0805, Tant, 1uF, 16V, 10%, Matsuo..Matsuo3 27 C29 JR060Cap, Trim, Ceramic, 2-6pF, 100V, Voltronics ..Voltronics1 28 C30 C0603C8R2J5GACCap, 0603, Ceramic, 8.2 pF, 5%, 50V, NPO..Kemet1 29 C31 C0603C680J5GACCap, 0603, Ceramic, 68 pF, 5%, 50V, NPO..Kemet1 30 C37,38 C0603C472M3RACCap, 0603, Ceramic, 4.7 nF, 20%, 25V, X7R..Kemet2 31 C40,41 278M6301225KCap, 0805, Tant, 2.2uF, 6.3V, 10%, Matsuo..Matsuo2 32 CR1 MMBD7000Diode, Dual, Small Signal, SOT-23, Fairchild..Fairchild1 33 Q1 MMBFJ309Transistor, JFET, N-Channel, SOT-23, Fairchild..Fairchild1 34 Q2 NDT456PTransistor, MOSFET, P-Channel, SOT-223, Fairchild..Fairchild1 35 Q3 MMBT2222Transistor, NPN, GP, SOT-23, Fairchild..Fairchild1 36 U2 MIC5213-5.0BC5IC, Regulator, LDO, 5.0V, 80mA, SC-70, Micrel..Micrel1 37 U3 AD8032ARMIC, OpAmp, 80 MHz, Rail-Rail, uSOIC-8, Analog DevicesAnalog Devices1 38 U4 MB510IC, Prescaler, 2.7 GHz, /16, 16/17, SOIC-8, Fujitsu..Fujitsu1 39 U5 MC145152DW2IC, PLL, Dual Modulus, SOIC-28, Freescale..Freescale1 40 U6 LMC7101AIM5IC, OpAmp, 1 MHz, Rail-to-Rail, SOT-23-5, NationalNational Semi1 41 Y1 CS5032H16.00MEEQ-UT Crystal, 16.00 MHz, 10pF, 5032 Pkg, Citizen/AbraconCitizen1 42 J1 A-1J1-CRConnector, Coax, RF, 3mm SMT, AmphenolAmphenol1 43 SW2 2182LPST-NDSwitch, 2-Position SMT DIP, CTSCTS1 ** OMIT C18, R24 789176.XLS

RF Exposure evaluation (FCC 2.1091) The EUT is a wireless device used in a mobile/fixed application, at least 20 cm from any body part of the user or nearby persons. The maximum conducted power is 5 W. According to the Applicant, the transmitter is most often used with 2 dBi monopole whips, but it can be used with about anything depending on the application. Using the formula for the Power Density S = EIRP/ 4πD 2 , the distance D, where the Maximum Permissible Exposure (MPE) satisfies the FCC 1.1310 limit (S=MPE) for General Population/Uncontrolled Exposure, can be calculated as: D ≥ √(EIRP/ 4πS) The MPE Limit in the frequency range 2450 – 2483.5 MHz is 10 W/m 2 . In the Table below, the minimum distance D (in meters) is presented for different antenna gain used with the 5 Watt and 2 Watt transmitters. Conducted Output Power = 5W Conducted Output Power = 2 W Antenna gain, dBi Antenna gain, numerical EIRP, Watt Minimum Distance, meter EIRP, Watt Minimum Distance, meter 0 1.0 5.0 1.0 2.0 >0.2 2 1.58 7.92 0.251 3.16 >0.2 5 3.16 15.8 0.355 6.32 0.22 10 10.0 50 0.631 20 0.4 15 31.6 158 1.121 63.2 0.71 20 100 500 1.995 200 1.26 25 316.2 1580 3.546 632.4 2.24 30 1000 5000 6.308 2000 4.0 User Manual must contain a Warning/ Guidance about RF Exposure.

EMC Report for for Advanced Microwave Products on the model: VT15SC File: 3117782-MPK-003 Page 1 of 31 Test Report Report Number: 3117782MPK-003 Project Number: 3117782 Report Date: April 20, 2007 Testing performed on the Video Transmitter Model Number: VT15SC FCC ID: U8KVT15SC to FCC Part 90 for Advanced Microwave Products A2LA Certificate Number: 1755-01 Test Performed by: Test Authorized by: Intertek Testing Services NA, Inc 1365 Adams Court Menlo Park, CA 94025 Advanced Microwave Products 2705 Old Hwy 40W, Suite C Verdi, NV, 89439 Prepared by: Date:April 20, 2007 David Chernomordik, EMC Technical Manager Reviewed by: Date: April 20, 2007 Ollie Moyrong, Ope rations Manager This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. This report must not be used to claim product endorsement by A2LA, NIST nor any other agency of the U.S. Government. Deleted: EMC De EMC Report for for Advanced Microwave Products on the model: VT15SC File: 3117782-MPK-003 Page 2 of 31 Report No. 3117782MPK-003 Equipment Under Test: Video/audio transmitter Trade Name: Advanced Microwave Products Model No.: VT15SC Serial No.: Not Labeled FCC ID: U8KVT15SC Applicant: Advanced Microwave Products Contact: Mr. Barry Lautzenhiser Address: 2705 Old Hwy 40W, Suite C Verdi, NV, 89439 Country USA Tel. number: 775-345 9933 Fax number: Applicable Regulation: FCC Part 90 Test Site Location: ITS - Site 1 1365 Adams Drive Menlo Park, CA 94025 Date of Test: March 10 - 31, 2007 We attest to the accuracy of this report: David Chernomordik EMC Technical Manager Ollie Moyrong Operations Manager Formatted: Indent: First line: 0" Deleted: ¶ Deleted: ¶ EMC Report for Advanced Microwave Products on the model: VT15SC File: 3117782-MPK-003 Page 3 of 31 TABLE OF CONTENTS 1.0 Introduction ...................................................................................................................5 1.1 Product Description ......................................................................................................... 5 1.2 Summary of Test Results ................................................................................................. 6 1.3 Test Configuration ........................................................................................................... 7 1.3.1 Support Equipment ................................................................................... 7 1.3.2 Block diagram of Test Setup..................................................................... 7 1.4 Related Submittal(s) Grants ............................................................................................. 7 2.0 RF Power Output ............................................................................................................ 8 2.1 Requirement.....................................................................................................................8 2.2 Test Procedure .................................................................................................................8 2.3 Test Equipment ................................................................................................................ 8 2.4 Test Results...................................................................................................................... 8 3.0 Occupied Bandwidth, 26-dB bandwidth......................................................................... 9 3.1 Test Procedure .................................................................................................................9 3.2 Test Equipment ................................................................................................................ 9 3.3 Test Results....................................................................................................................... 9 4.0 Emission Mask ................................................................................................................ 12 4.1 Test Procedure ............................................................................................................... 12 4.2 Test Equipment .............................................................................................................. 12 4.3 Test Results....................................................................................................................12 5.0 Out of Band Emissions at Antenna Terminal .............................................................. 17 5.1 Requirement................................................................................................................... 17 5.2 Test Procedure ............................................................................................................... 17 5.3 Test Equipment .............................................................................................................. 17 5.4 Test Results....................................................................................................................17 6.0 Spurious Radiation ....................................................................................................... 26 6.1 Requirement.....................…

Text truncated - open the document above for the full version.