U8X-NB0024GXXRFID Reader

1 TYPICAL INSTALLATION INSTRUCTIONS & WARRANTY INFORMATION Simplex Station 70-Gal. Capacity E/One Sewers TM 2 Environment One Grinder Pump Feature Identification 1. GRINDER PUMP BASIN – High density polyethylene (HDPE). 2. ACCESSWAY COVER – FRP 3. ELECTRICAL QUICK DISCONNECT (EQD) – Cable from pump core terminates here. 4. POWER AND ALARM CABLE – Circuits to be installed in accordance with local codes. 5. ALARM PANEL – NEMA 4X enclosure. Equipped with circuit breakers. Locate according to local codes. 6. ALARM DEVICE – Every installation is to have an alarm device to alert the homeowner of a potential malfunction. Visual devices should be placed in very conspicuous locations. 7. INLET – EPDM grommet (4.5" ID). For 4.5" OD DWV pipe. 8. WET WELL VENT – 2.0" tank vent, supplied by factory in units with accessways. 9. GRAVITY SERVICE LINE – 4" DWV, (4.5" OD). Supplied by others. 9a. STUB-OUT – 4" X 5' Long watertight stub-out, to be installed at time of burial unless the gravity service line is connected during installation. Supplied by others. 10. DISCHARGE VALVE – 1-1/4" Female pipe thread. 11. DISCHARGE LINE – 1-1/4" Nominal pipe size. Supplied by others. 12. CONCRETE ANCHOR – See Ballast Calculations for specific weight for station height. Supplied by others. 13. BEDDING MATERIAL – 6" minimum depth, round aggregate, (gravel). Supplied by others. 14. FINISHED GRADE – Grade line to be 1” to 4” below removable lid and slope away from the station. 15. VENT – Indoor installation. See section 6, Venting, on page 6. 16. VALVE – Full ported ball valve. Recommended option; for use during service operations. Supplied by others. 17. CONDUIT – 1" or 1-1/4", material and burial depth as required per national and local codes. Conduit must enter panel from bottom and be sealed per NEC section 300.5 & 300.7. Supplied by others. 18. UNION – 1-1/4" or compression type coupling. Supplied by others. (Do not use rubber sleeve and hose clamp type coupling.) 19. VALVE – Ball valve, must provide a full-ported 1-1/4" round passage when open. Supplied by others. 20. REBAR – Required to lift tank after ballast (concrete anchor) has been attached, 4 places, evenly spaced around tank. 3 FAILURE TO COMPLY WITH INSTALLATION INSTRUCTIONS WILL VOID WARRANTY Figure 1b Figure 1a SEAL CONDUIT PER NEC SECTION 300.5 & 300.7 4 The Environment One Grinder Pump is a well engineered, reliable and proven product: proper installation will assure years of trouble-free service. The following instructions define the recommended procedure for installing the grinder pump station. These instructions cover the installation of units with and without accessways. This is a sewage handling pump and must be vented in accordance with local plumbing codes. This pump is not to be installed in locations classified as hazardous in accordance with National Electric Code, ANSI / NFPA 70. All piping and electrical systems must be in compliance with applicable local and state codes. 1. REMOVE PACKING MATERIAL: The User Instructions must be given to the home owner. Hardware supplied with the unit, if any, will be used at installation. 2. TANK INSTALLATION: The tank is supplied with a standard grommet for connecting the 4" DWV (4.50" outside Dia.) incoming sewer drain. Other inlet types and sizes are optional (caution 4" DR-35 pipe is of smaller diameter and won’t create a water tight joint with the standard grommet). Please confirm that you have the correct inlet before continuing. If a concrete ballast is attached to the tank lift only by the lifting eyes, (rebar) embedded in the concrete. Do not drop, roll, or lay tank on its side. This will damage the unit and void the warranty. If the tank has no accessway (Fig. 1b) (Indoor Installation): The pump may be installed on or in the basement floor (see Fig. 1b). If the tank is to be set on the floor it must be a flat and level bearing surface. If the tank is to go into the basement floor, it must be anchored to prevent unit from floating due to high ground water (see Chart 1, page 12 for weight). If the tank is to go in the floor: A hole of the correct width and depth should be excavated. The tank must be placed on a 6" bed of gravel made up of naturally rounded aggregate, clean and free flowing, with particle size not less than 1/8" or more than 3/4" in diameter. The wet well should be leveled and filled with water prior to pouring the concrete to prevent the tank from shifting. If it’s necessary to pour the concrete to a level above the inlet, the inlet must be sleeved with an 8" tube before pouring. There must be a minimum clearance of three feet directly above the tank to allow for removal of the pump core. If the tank has an accessway (Fig. 1a): Excavate a hole to a depth, so that the removable cover extends above the finished grade line. The grade should slope away from the unit. The diameter of the hole must be large enough to allow for a concrete anchor. Place the unit on a bed of gravel, naturally rounded aggregate, clean and free flowing, with particles not less than 1/8" or more than 3/4" in 120 VOLT WIRING Figure 2a 5 PC0051GXX) be installed between the pump discharge and the street main on all installations. Never use a ball type valve as a check valve. We recommend the valve be installed as close to the public right-of-way as possible. Check local codes for applicable requirements. CAUTION: Redundant check valves on station laterals and anti-siphon/check valve assemblies on grinder pump cores should not be used as system isolation valves during line tests. If the tank has no accessway: (Indoor Installation) The discharge connection is a 1-1/4" male NPT. The discharge piping must incorporate a shut-off valve and a union with a minimum pressure rating of 160 PSI, or a suitable piping disconnect to allow for removal of the pump core. The valve should be of the type that provides a full-ported passage (i.e. a ball or gate valve). A standard 1-1/4" union or a compression type coupling should be …

Text truncated - open the document above for the full version.

Microcontroller 1.9 MHz RF Return Detector Chip Antenna Alarm Control Relay Pump Control Relay RF Signal Chip 125kHz NextGen RFID Flow Chart Environment One Corporation FCC ID: FCC ID: U4I.NB0034GXX Power Supply Transponder Alarm Pressure Switch On/Off Pressure Switch 3/28/07 SM

1.00 0.09 0.33 0.56 0.19 0.19 2.17 0.14 0.46 FCC ID:U8X-NB0024GXX NOTES: 1. THIS IS A CTF (CRITICAL TO FUNCTION) DRAWING. CAD MODEL MUST BE USED TO OBTAIN REMAINING PART GEOMETRY. CTF DRAWING IS ONLY MEANT TO PROVIDE DIMENSIONS SPECIFIC TO PART FUNCTIONALITY. 2. MATERIAL: Polypropylene COLOR: Black HARDNESS: TBD Durometer FORMULA: TBD SUPPLIER: TBD R 0.05 R 4.95 R 9.01 REVISIONS REV.DESCRIPTIONDATEAPPROVED 2Added third text line, drawing on template3/12/07dlachut 3.875 changed to 1.003/15/07dlachut MM .XXX ±0.025 ±0.25 ANGLE ±.5° .X .XX ±0.13 INCH SH 1 OF 1 DRAWING NUMBER ENG USE ONLY: REV: 3 VER: DENSITY:0.04 4/17/2007 VOLUME: 0.19 E/ONE SHOP PRACTICE PER E-5000-01 WEIGHT: 0.01 SERVICE #: -ENG MODEL: NB0044P01 nameplate, molded SCALE: 1:1 ANGLE ±.5° .XXX ±0.005 .XX ±0.02 ±0.1.X DEFAULT TOLERANCES RELEASED: UNITS IN MM[IN] & GRAMS - ENG: - DIMENSIONING AND TOLERANCING AS PER ASME Y14.5M-1994 CHK: SSB ENVIRONMENT ONE CORPORATION UNLESS OTHERWISE SPECIFIED THE FOLLOWING APPLIES NB0044P01 nameplate, molded.SLDDRW Reference Location: X:\Next Gen GP Program\Engineering\Controlled Files\Derek's Parts\NB0044P01 Nameplate, molded\NB0044P01 nameplate, molded : Configuration: Default Last Saved by: skennard : Tuesday, April 17, 2007 2:33:48 PM NB0044P01 MATERIAL: As Noted DR: dlachut 1/1/2007 NB0044P01 3 Nameplate, Molded -

NextGen Transceiver Specification Sheet Note: This assembly will only work properly in combination with the mating Transponder (PA2117G01) Prints Schematic PB0986P01 PCB PB0987P01 ASSY PA2116G01 (240 volt), G02 (120 Volt) PC Board & Assembly Material FR4 Glass Epoxy Board Layers 2 Board Thickness .062” Manufacture of the board WayTec, Lynchburg, VA, UL E75730 Assembled by MackTech, Westford,MA, (978) 392-5500 Conformal Coat Humiseal #1B73AP or Equivalent (UL File # E105698) Communication Coil PA2132P01 Operational Information Input Voltage Range 70 to 240 volts AC (Assembly Dependent) Max Operating Current 5 Amps (Including onboard Relay Contacts) Consumption Operating Frequency 50-60 Hz Max Current on Motor, L1, and Shunt Circuit 20 Amps SSR1 AC Solid State Relay Max Output Voltage & Current 240 Volt & 100ma (UL File# E69938) K1 Relay Max Output Voltage & Current 240 Volt & 4 Amps (UL File# E22575) Wire Spec Stranded copper, thermoplastic insulation, .031 nom wall, 105c, 600 volts, ul1015 On Board Power Supply Input Voltage 120 or 240 VAC 50/60 Hz (Assembly Dependent) Output Voltage 25 VDC Output Max Current 150 ma Normal Operating Current 60 ma Protection Resistive and PTC Fused RFID Information RFID Chip EM4095 EM Microelectronics Frequency 125KHz Nominal (100K-150KHz) Voltage to Output Coil 50 VAC RMS Current to Output Coil 120 ma RMS Protection Current Limiting Resistor and RFID Chip is self protected from the coil shorting out Last Updated 1/16/2007 SM

NextGen Transponder Specification Sheet Note: This assembly will only work properly in combination with the mating Transceiver (PA2116G01, G02) Prints Schematic PB0988P01 PCB PB0989P01 ASSY PA2117G01 PC Board & Assembly Material FR4 Glass Epoxy Board Layers 2 Board Thickness .062” Manufacture of the board WayTec, Lynchburg, VA, UL E75730 Assembled by MackTech, Westford,MA, (978) 392-5500 Conformal Coat Humiseal #1B73AP or Equivalent (UL File # E105698) General Information Input Voltage Range Inductive coupled from Transceiver - 5 volts Max Operating Current 2 Milliamps Consumption Operating Frequency 125kHz Nominal (100K-500KHz) Wire Spec Stranded copper, thermoplastic insulation, .031 nom wall, 105c, 600 volts, ul1015 On Board Power Supply Input Voltage Inductively Coupled from Transceiver, 5 volts Nominal Protection Resistive RFID Information Chip MC14536B ON Semiconductor Programmable Timer Frequency 125KHz Voltage no Output Coil 5 VAC RMS Current from Output Coil 2 Milliamps DC Protection Current Limiting Resistor Output Frequency Out of range None Both Switches Inactive 150 Hz On/Off Active Only 300 Hz Alarm Active Only 600 Hz On/Off & Alarm Active 1200 Hz Last Updated 1/26/2007 SM

NextGen RFID Order of Operation FCC ID: U4I.NB0034GXX 3/28/07 SM • Power is supplied o 120 or 240 volt AC o Alarm relay closed o Pump relay open • Microcontroller runs a start up diagnostic • RFID Controller Chip sends out 125kHz Signal • Transponder assembly receives the signal, extracts energy from it to provide DC power to Transponder Circuit. o Transponder checks alarm and on/off pressure switch state (are switches open or closed) o Based on the switch states, the transponder will return a signal; ƒ Both Switches Inactive 150 Hz ƒ On/Off Active Only 300 Hz ƒ Alarm Active Only 600 Hz ƒ On/Off & Alarm Active 1200 Hz o The transponder continuously monitors the switches • Transceiver receives the signal back from the Transponder and; o Both Switches Inactive 150 Hz ƒ Idle o On/Off Active Only 300 Hz ƒ Pump is powered o Alarm Active Only 600 Hz ƒ Alarm is powered o On/Off & Alarm Active 1200 Hz ƒ Pump and Alarm is powered o If the transceiver loses or detects a frequency not within +- 30% of the above, the Alarm will be powered and the pump will be off. • If the Transceiver loses power, the Alarm contact will be closed, the pump contacts will open

© Coilcraft, Inc. 2006 Specifications subject to change without notice. Please check our website for latest information. Document 324-1 Document 324-1 Revised 01/24/05 RFID Transponder Coils – 4308RV Coilcraft’s 4308RV antenna coils are high performance devices intended for RFID applications at 125 kHz. These low profile parts have an extended length that allows longer read ranges. An encapsulated top ensures reliable pick and place operations. Core construction and encapsu- lation are rated for 125°C, which makes these transpon- ders ideal for higher temperature applications. The 4308RV transponders coils are available in 5% and 2% tolerances. In addition to the standard models shown, Coilcraft can design coils to operate at other frequencies. Coilcraft Designer’s Kit C383 contains four samples of all 5% inductance tolerance parts. To order, contact Coilcraft or visit http://order.coilcraft.com. 1. When ordering, please specify tolerance and packaging codes: 4308RV-905XJLD Tolerance: G = 2%J = 5% (Table shows stock tolerances in bold.) Packaging: D=13′′ machine-ready reel. EIA-481 embossed plastic tape (3000 parts per full reel). B= Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance and Q measured using Agilent/HP 4192A impedance analyzer. InductanceReadMatchingDCRSRF at 125 kHz 2 Qdistance 4 Sensitivity 5 capacitor 6 max 7 typ 8 Part number 1 (mH)Tolerance 3 min 2 (in. / cm)(mV/μT)(pF)(Ohms)(kHz)Color code 4308RV-374X_L_0.375,22622 / 55.99.8243806.51800Orange Violet Yellow 4308RV-404X_L_0.405,22623 / 58.410.3840507.15000Yellow Black Yellow 4308RV-704X_L_0.705,22025 / 63.513.962320196600Violet Black Yellow 4308RV-904X_L_0.905,22226 / 66.016.061800214800White Black Yellow 4308RV-115X_L_1.085,22430 / 76.217.781500244300Brown Brown Green 4308RV-205X_L_1.975,22834 / 86.424.90823311750Red Black Green 4308RV-245X_L_2.385,23037 / 94.028.21681341700Red Yellow Green 4308RV-295X_L_2.895,23037 / 94.032.12561421900Red White Green 4308RV-335X_L_3.305,23038 / 96.534.96491481425 Orange Orange Green 4308RV-415X_L_4.155,22739 / 99.141.35391701620Yellow Brown Green 4308RV-495X_L_4.905,22638 / 96.547.17331931150Yellow White Green 4308RV-685X_L_6.805,22841 / 104.161.712381101080Blue Gray Green 4308RV-715X_L_7.105,22742 / 106.765.602281141050Violet Brown Green 4308RV-725X_L_7.205,22840 / 101.666.67225114965Violet Red Green 4308RV-815X_L_8.105,22842 / 106.775.08200125965Gray Brown Green 4308RV-905X_L_9.005,23040 / 101.684.64180125725White Black Green 3. Tolerances in bold are stocked for immediate shipment. 4. Read distance measured using the KEELOQ ® Transponder Evaluation Kit part number DM303005 from Microchip. Distance was recorded as the voltage across the resonant circuit dropped below 10 mV. 5. Sensitivity measured in accordance with Coilcraft application note “Measuring Sensitivity of Transponder Coils.” 6. Matching capacitor value required for parallel resonant circuit operating at 125 kHz. 7. DCR measured on micro-ohmmeter. 8. SRF measured using Agilent/HP 8753D network analyzer. 9. Operating temperature range −40°C to +125°C. 10. Electrical specifications at 25°C. See Qualification Standards section for environmental and test data. © Coilcraft, Inc. 2006 RFID Transponder Coils – 4308RV Specifications subject to change without notice. Please check our website for latest information. Typical Q vs FrequencyTypical L vs Frequency 0.110 2,79 0.333 8,46 0.473 12,01 0.070 1,78 Recommended Land Pattern 0.108 ±0.004 2,74 ±0,10 0.040 1,01 ref 0.020 0,51 ref 0.450 11,43 max max 0.433 ±0.005 10,99 ±0,127 0.124 3,15 0.079 ±0.004 2,00 ±0,10 0.040 0,89 Document 324-2 Document 324-2 Revised 01/24/05 110 -404 -205 1001000 10000 Frequency (kHz) 0 60 50 40 30 20 10 Q factor -815 -415 1101001000 10000 Frequency (kHz) 0 12 10 8 6 4 2 Inductance (mH) -404 -205 -815 -415 Terminations:Silver-palladium-platinum-glass frit Weight:230 – 250 mg Tape and reel:3000/13′′ reel 24 mm tape width For packaging data see Tape and Reel Specifications section.

ITEM QTY REF DES PART NUMBER DESCRIPTION MANUFACTURER 1 1 - PB0987P01PCB, NEXT GEN XCVREnvironment One Corp 2 1 SSR1 CPC1965Y AC SOLID STATE RELAY CLARE 3 1 C28 C2012X7R2A223K CAP CER .022uF 100V X7R 10% 0805 TDK Corporation 4 1 C5 C2012C0G2A152J CAP CER 1500PF 100V C0G 5% 0805 TDK Corporation 5 1 C4 GRM2195C2A330JZ01D CAP CER 33PF 100V 5% NPO 0805 Murata 6 8 C11 C13 C22 C26-27 C30 C32 C34 C0805C104K5RACTU CAP .10UF 50V CERAMIC X7R 0805 Kemet 7 1 C24 C0805C471J5GACTU CAP, 470pF, 50V, NP0, 0805, Pb FREE Kemet 8 1 C2 C0805C101J1GACTU CAP CERAMIC 100PF 100V NP0 0805 Kemet 9 1 C1 C1206C272F1GAC CAP CER 2700PF 100V C0G 1% 1206 Kemet 10 1 C17 TCA1A106M8R CAP TANT 10UF 10V 20% SMD ROHM 11 3 C10 C14 C29 B45196H2475M109 CAP TANT 4.7UF 10V 20% Kemet 12 1 C31 EKMG500ELL100ME11D CAP 10UF 50V ELECT KMG RAD United Chemi-Con 13 1 C21 EKZE100ELL122MJ20S CAP 1200UF 10V ELECT KZE RAD United Chemi-Con 14 1 C15 EKY-160ELL471MH15D CAP 470UF 16V ELECT KY RAD United Chemi-Con 15 1 C7 ECQ-U2A474ML CAP .47UF 250/275VAC ECQ-UL Panasonic - ECG 16 1 C18 EKZE350ELL122ML20S CAP 1200UF 35V ELECT KZE RAD United Chemi-Con 17 1 C8 ECQ-V1H103JL CAP .01UF 50V STACK METAL FILM Panasonic - ECG 18 3 C9 C20 C25 ECQ-V1H223JL CAP .022UF 50V STACK METAL FILM Panasonic - ECG 19 2 C16 C19 ECQ-V1H683JL CAP .068UF 50V STACK METAL FILM Panasonic - ECG 20 1 C6 ECQ-V1H104JL CAP .1UF 50V STACK METAL FILM Panasonic - ECG 21 2 C12 C23 EKY-6R3ELL331MF11D CAP 330UF 6.3V ELECT KY RAD United Chemi-Con 22 1 L1 6000-221K-RC INDUCTOR HI CURRENT RADIAL 220UH, Pb Free JW Miller / Bourns 23 1 J1 Make from PBC36DFANCONNECTOR,0.100" PITCH,DOUBLE ROW,14 POS Sullins 24 2 D4-5 1N4007-TP RECTIFIER 1A 1000V DO-41, RoHS Micro Commercial 25 2 D3 D6 CGRA4007-G DIODE GEN PURPOSE 1000V 1A SMA, RoHS Comchip Technology 26 1 D7 1N4148 DIODE SGL JUNC 100V 4.0NS DO-35 Fairchild Semiconductor 27 1 D8 MBRA140T3 DIODE SCHOTTKY 40V 1A SMA ON Semiconductor 28 1 D2 DFLZ12-7 DIODE ZENER 1W 12V POWERDI123 Diodes Inc 29 1 J2 Make From PBC36SFANHEADER, .1" PITCH, 3 POS Sullins 30 1 U5 MC34063ECN IC REG SW BOOST/BUCK 1.5A 8SOIC Texas Instruments 31 1 U4 AD71056ARZ Energy Metering IC with Integrated Oscillator Analog Devices 32 1 D1 LTST-C170CKT LED RED CLEAR 0805 Lite-On 33 1 U2 MSP430F1122IDW IC 16BIT MCU 4KB FLASH 20-SOIC Texas Instrument 34 2 D9-10 CD0805-S01575 DIODE SWITCH 75V 200MW Bourns 35 1 NTC1 NCP21XQ471J03RA THERMISTOR 470 OHM NTC 0805 SMD Murata 36 1 U9 LMC6482AIM IC OP AMP DUAL CMOS R-R 8-SOIC National Semiconductor 37 1 U7 TLP421(GR) PHOTOCOUPLER TRANS-OUT 4DIP Toshiba 38 1 R26 3296Y-1-504 POT 500K OHM 3/8" SQ CERM SL MT Bourns 39 1 PTC1 2381 660 56393 THERMISTOR PTC 120 OHM 265V BC COMPONENTS 40 1 PTC2 YM120D170N250 THERMISTOR PTC OCP 25 OHM 25C GE Sensing 41 1 U6 LM7805CT IC REG 1A POS 0-125DEG C TO-220 Fairchild Semiconductor 42 1 U3 LM78L05ACZ IC REG 0.1A 0-125DEG C TO-92, Pb FREE Fairchild Semiconductor 43 1 U8 FAN2500S33X 100 mA CMOS LDO Regulator Fairchild Semiconductor 44 1 K1 T7CS5D-06 RELAY PWR PC MNT SPDT 12A 6VDC Tyco 45 1 R39 ERJ-6ENF2260V RES 226 OHM 1/8W 1% 0805 Panasonic - ECG 46 1 R6 ERJ-6ENF3400V RES 340 OHM 1/8W 1% 0805 Panasonic - ECG 47 1 R7 ERJ-6ENF4990V RES 499 OHM 1/8W 1% 0805 Panasonic - ECG 48 1 R12 ERJ-6ENF1501V RES 1.50K OHM 1/8W 1% 0805 Panasonic - ECG 49 1 R28 ERJ-6ENF5113V RES 511K OHM 1/8W 1% 0805 Panasonic - ECG 50 1 R30 ERJ-6ENF5902V RES 59.0K OHM 1/8W 1% 0805 Panasonic - ECG 51 1 R10 ERJ-6GEYJ622V RES 6.2K OHM 1/8W 5% 0805 Panasonic - ECG 52 1 R14 ERJ-6ENF7501V RES 7.50K OHM 1/8W 1% 0805 Panasonic - ECG 53 1 R38 ERJ-6ENF95R3V RES 95.3 OHM 1/8W 1% 0805 Panasonic - ECG 54 2 R8-9 ERJ-6ENF1541V RES 1.54K OHM 1/8W 1% 0805 SMD Panasonic - ECG 55 3 R16-18 ERJ-6GEYJ1R0V RES 1 OHM 1/8W 5% 0805 Panasonic - ECG 56 1 R1 ERJ-6GEYJ200V RES 20 OHM 1/8W 5% 0805 Panasonic - ECG 57 1 R3 ERJ-6GEYJ360V RES 36 OHM 1/8W 5% 0805 Panasonic - ECG 58 1 R4 ERJ-6GEYJ271V RES 270 OHM 1/8W 5% 0805 SMD Panasonic - ECG 59 1 R2 ERJ-6GEYJ301V RES 300 OHM 1/8W 5% 0805 SMD Panasonic - ECG 60 2 R23 R41 ERJ-6GEYJ471V RES 470 OHM 1/8W 5% 0805 SMD Panasonic - ECG 61 1 R15 ERJ-6GEYJ621V RES 620 OHM 1/8W 5% 0805 SMD Panasonic - ECG 62 2 R31 R34 ERJ-6GEYJ102V RES 1.0K OHM 1/8W 5% 0805 Panasonic - ECG 63 1 R22 ERJ-6GEYJ155V RES, 1.5M OHM, 1/8W, 5%, 0805, Pb FREE Panasonic - ECG 64 2 R35-36 ERJ-6GEYJ182V RES 1.8K OHM 1/8W 5% 0805 Panasonic - ECG 65 2 R29 R40 ERJ-6GEYJ103V RES 10K OHM 1/8W 5% 0805 Panasonic - ECG 66 1 R27 ERJ-6GEYJ123V RES 12K OHM 1/8W 5% 0805 Panasonic - ECG 67 1 R21 ERJ-6GEYJ105V RES 1M OHM 1/8W 5% 0805 Pb Free Panasonic - ECG 68 1 R11 ERJ-6GEYJ222V RES 2.2K OHM 1/8W 5% 0805 Panasonic - ECG 69 1 R32 ERJ-6GEYJ203V RES 20K OHM 1/8W 5% 0805, Pb FREE Panasonic - ECG 70 1 R37 ERJ-6GEYJ302V RES 3.0K OHM 1/8W 5% 0805, Pb FREE Panasonic - ECG 71 1 R24 ERJ-6GEYJ304V RES 300K OHM 1/8W 5% 0805 Panasonic - ECG 72 1 R33 ERJ-6GEYJ513V RES 51K OHM 1/8W 5% 0805 Panasonic - ECG 73 1 R25 CFR-50JB-330K RES 330K OHM 1/2W 5% CARBON FILM Yageo 74 2 R19-20 MFR-25FBF-634K RES 634K OHM 1/4W 1% METAL FILM, AXIAL, Pb FREEYageo 75 1 R5 RSF100JB-120R RES 120 OHM 1W 5% METAL OXIDE Yageo 76 1 R13 RSF200JB-180R RES 180 OHM 2W 5% METAL OXIDE Yageo 77 1 U1 EM4095HMSO16A RFID TRANSCEIVER EM MICROELECTRONICS 78 2 Q1-2 2N3904BU IC TRANS NPN SS GP 200MA TO-92 Fairchild Semiconductor 79 1 C3 TZ03P450F169B00 CAP 6.8-45.0PF 6MM TOPADJ YEL Murata Bill Of Materials for PB0986P01 Rev 6.sch on Thu Jan 04 11:53:41 2007 G01 - 240 V, 2 leg 80 1 T1 FP24-250 TRANSFORMER 12VAC .5A FLAT PACK PWR Triad Magnetics 81 1 WP4, WP5PA2148P01Calibrated Shunt Environment One Corp 82 8" WP1BlueBlue, 16AWG Stranded- See Notes 83 8" WP2OrangeOrange, 16AWG Stranded - See Notes 84 8" WP3L2White, 16AWG Stranded - See Notes 85 14" WP6MotorWhite, 16AWG Stranded - See Notes 86 9" WP7L1Black, 16AWG Stranded - See Notes 87 8" WP8CoilRed, 16AWG Stranded - See Notes 88 1 WP9 , WP10NA0003G01ASM, XCVR COIL Environment One Corp 89 12" WP11Wet ProbeYellow, 18AWG Stranded - See Notes 90 9" WP21GNDGreen w/ Yellow Stripe, 14AWG Strand…

Text truncated - open the document above for the full version.

Item Qty ReferencePart Number Description 11PB0989P01 Rev 4 PCB, NEXT GEN XPNDR 21Q1 2N7002-7-F MOSFET N-CH 60V 115MA SOT-23 31C1 C0805C102J5GACTU CAP CERAMIC 1000PF 50V NP0 0805 41C2 C0805C104Z5UACTU CAP .10UF 50V CERAMIC Z5U 0805 51C3 ECS-T1AZ105R CAP 1.0UF 10VDC TES SERIES 61C4 C0805C101F1GAC CAP CERAMIC 100PF 100V NP0 0805 71C6 C0805C820F1GAC CAP CERAMIC 82PF 100V NP0 0805 81C5 Not Installed 91L1 4308RV-905XGL RFID TRANSPONDER COIL 4308RV SERIES 101U1 MC14536BDWR2 IC TIMER PROG 24ST RIPPLE 16SOIC 115D1-3 D5-6 CD0805-S01575 DIODE SWITCH 75V 200MW 121R9 RC0805JR-0710RL RES 10 OHM 1/8W 5% 0805 4R1 R4 RC0805JR-07100KL RES 100K OHM 1/8W 5% 0805 R6-7 131R2 RC0805JR-07180KL RES 180K OHM 1/8W 5% 0805 142R3 R10 RC0805JR-071ML RES 1.0M OHM 1/8W 5% 0805 152R5 R8 RC0805JR-073M3L RES 3.3M OHM 1/8W 5% 0805 161D4 MM3Z5V1T1 DIODE ZENER 200MW 5.1V SOD323 176" WP1 Red, 22AWG 186" WP2 Violet, 22AWG 196" WP3 Blue, 22AWG 206" WP4 Orange, 22AWG Bill Of Materials for PB0988P01_REV03.sch on Mon Jul 17 07:29:57 2006 Manufacturer E-One DIODES INC Kemet KEMET PANASONIC KEMET KEMET COILCRAFT ON SEMICONDUCTOR (MOTOROLA) Bourns YAGEO YAGEO YAGEO YAGEO YAGEO ON SEMI

12/19/2006 5 SCH, NEXT GEN XCVR SHEET: OF C Tubbs <Checked By> <QC By> <Released By> <Checked Date><QC Date><Release Date> Environment One Corporation <Code> B PB0986P01 N/A 1 3 REV: SIZE: CODE: DRAWN: DATED: DATED: CHECKED:QUALITY CONTROL: DATED: DATED: RELEASED: COMPANY:TITLE: DRAWING NO: SCALE: REVISION RECORD APPROVED: ECO NO: ABD DATE: 1 2 3 4 5 6 DCAB C LTR Decoupling CAPS U1 U2 Pins 4, 7 Pin 1 Pin 14 (associated with indicated IC/pins) CAP input PS for Watt Meter BUCK Power Supply for RFID Pins 1, 5 JP3 JP1 JP2 (To be connected to CHASSIS GND at board mounting locations) (SOURCE) (SOURCE) (SOURCE) Note 7 (SOURCE) (SOURCE) +3.3V Regulator U9 (Casting GND bond point) C104.710V 20% C11.10 C13.10 12 7865 43 T1 12 D4 1N4007-TP + C1820%1200uF35VLow ESR + C2120%1200uF10VLow ESR + C2320%330uF6.3VLow ESR C24470pF 1 2 R14 7.50K 1% 12 D8MBRA140T3 L1 6000-221K-RC 1 2 R16 1 1 2 R17 1 1 2 R18 1 1 IN 2 GND 3 OUT U6 LM7805CT 12 D5 1N4007-TP C7 0.47 20% 275VAC + C1220%330uF6.3VLow ESR + C1520%470uF16VLow ESR 3 IN 2 GROUND 1 OUT U3 LM78L05ACZ D2DFLZ12-7 12 D3 CGRA4007-G 12 D6CGRA4007-G 1 2 R5 120 1W MOF 1 2 R25 330K 1/2 W 1 SW_C 2 SW_E 3 CAP 8 DRV_C 7 I_SEN 5 IN 4 GND 6 VCC U5 MC34063ECN C144.710V 20% PTC2 25 ohm 265VAC WP15 WP13 WP14 WP12 1 WP16 1 WP17 12 R121.50K1% 1 WP18 1 WP19 1 WP20 3 EN 2 GND 1 VIN 5 VOUT 4 ADJ/BYP/ERR U8 FAN2500S33X C27 .10 C34.10 1 WP21 +5V_WM +7.5V RF_CHASSIS_GND RF_CHASSIS_GNDRF_CHASSIS_GND +3.3V RF_CHASSIS_GNDRF_CHASSIS_GND +5V_RF +5V_RF L2L1 UNREG_DC +3.3V +5V_RF RF_CHASSIS_GND RF_CHASSIS_GND +3.3V RF_CHASSIS_GND Notes: 1. All resistor value in ohms, 5% tolerance unless otherwise noted. 2. All capacitor values in uF, 50V, 5% tolerance unless otherwise noted. 3. Power and Ground connections are not shown on each IC. Refer to Power and Ground table for proper IC pin connections to these nets. 4. Refer to decoupling capacitors for each IC’s specific components. 5. Digital circuitry is com m on to CHASSIS. W P16 – W P20 are provided to tie net to chassis via board mounting holes. W att meter circuit com m on to L2. 6. Calibrated shunt connected in series with motor current. 7. Transformer T1 is default wired for 240V operation. Refer to jumper table for 120V configuration. 8. Install jumper J4 to calibrate watt meter voltage reference. 9. Schematic drawn for 240V operation. Refer to proper Assembly drawing PA2116GXX for correct parts list. 10. Part not installed GND NETS REF DES RF_CHASSIS_GND +5V_RF +5V_WM +3.3V U1 1,5 4, 7 U2 4 2 U4 1 U9 4 8 Power and Ground Signal - Pin Cross Reference Table VCC NETS (Note 7) Jumper 120V 240V JP1 INSTALL OMIT JP2 CUT DEFAULT JP3 INSTALL OMIT TRANSFORMER CONFIGURATION Operation SCH, NEXT GEN XCVR 5 12/19/2006 LTR C BACD 65 4 3 2 1 DATE: DBA ECO NO: APPROVED: REVISION RECORD SCALE: DRAWING NO: TITLE:COMPANY: RELEASED: DATED: DATED: QUALITY CONTROL:CHECKED: DATED: DATED: DRAWN: CODE: SIZE: REV: 3 2 N/A PB0986P01 B <Code> Environment One Corporation <Release Date><QC Date><Checked Date> <Released By> <QC By> <Checked By> C Tubbs SHEET: OF TO TRANSCEIVER COIL TO ALARM CIRCUIT BASE RFID CIRCUIT CLIBRATION JUMPER Note 8 J2 JTAG INTERFACE Note 10 Note 10 ZC 16 28 SSR1 CPC1965Y 12 R120 12 R2 300 D1 LTST-C170CKT C12700pF1% C2100pFN.I. C4 33pF C51500pF 1 2 PTC1 120 ohm 265VAC 14 SHD 15 FCAP 16 DC2 12 MOD 8 DMOD_IN 10 CDEC_IN 2 RDY/CLK 3 ANT1 6 ANT2 13 DMOD_OUT 9 CDEC_OUT 11 AGND U1 EM4095HMSO16A 1 2 R13 180 2W C36.8-45.0 pFN.I. C22 .10 1 2 R4 270 C6 0.1 C90.022 C80.01 52 314 K1 T7CS5D-06 1 2 R3 36 1 2 R11 2.2K 1 2 3 Q1 2N3904BU 12 D7 1N4148 12 R23 470 WP1 WP2 WP8 WP9 WP10 1 2 R2712K 1 2 R31 1.0K J1-7J1-3 12 R3220K 12 R3351K 1 2 3 Q2 2N3904BU 1 2 R34 1.0K 12 R351.8K 12 R361.8K 1 2 R37 3.0k -+ 23 1 U9-A LMC6482AIM -+ 65 7 U9-B LMC6482AIM 1 TEST 3 P2.5/ROSC 5 XOUT 6 XIN 7 RST/NMI 8 P2.0/ACLK/A0 9 P2.1/INCLK/A1 10 P2.2/TA0/A2 20 P1.7/TA2/TDO/TDI 19 P1.6/TA1/TDI/TCLK 18 P1.5/TA0/TMS 17 P1.4/SMCLK/TCK 16 P1.3/TA2 15 P1.2/TA1 14 P1.1/TA0 13 P1.0/TACLK/ADC10CLK 12 P2.4/TA2/A4/VREF+ 11 P2.3/TA1/A3/VREF- U2 MSP430F1122IDW 12 R24 300K J1-1J1-5 J2-1J2-2 J1-9 J1-11 12 R4010K J1-2J1-4J1-6J1-8 J1-10J1-12 J1-13 J1-14 12 R41 470 J2-3 +3.3V +7.5V RF_CHASSIS_GND L1 COIL BLUE ORANGE RF_CHASSIS_GND +3.3V RF_CHASSIS_GND +5V_RF RF_CHASSIS_GND RF_CHASSIS_GND RF_CHASSIS_GND LEAK_DETECT BROWN_OUT_DETECT +3.3V RF_CHASSIS_GND WATT_METER RESET TEST TDITMSTCKTDO +3.3V +3.3V TDI TCK TDO TDI RESET RF_CHASSIS_GND +3.3V TEST +3.3V +3.3V RF_CHASSIS_GND 12/19/2006 SCH, NEXT GEN XCVR C Tubbs <Checked By> <QC By> <Released By> <Checked Date><QC Date><Release Date> Environment One Corporation <Code> B PB0986P01 5 N/A 3 3 REV: SIZE: CODE: DRAWN: DATED: DATED: CHECKED:QUALITY CONTROL: DATED: DATED: RELEASED: COMPANY:TITLE: DRAWING NO: SHEET: OF SCALE: REVISION RECORD APPROVED: ECO NO: ABD DATE: 1 2 3 4 5 6 DCAB C LTR LEAK DETECTION BROWN OUT DETECT WATT METER To Current Shunt Note 6 D9 MMBD4148W D10 MMBD4148W 12 R22 1.5M C280.02210% 12 R21 1M WP11 12 R28 511K 12 R3059.0K 1 2 R2910K + C3120%10uF50V Low ESR C32.10 C160.06850V 1 2 R6 340 1% 1 2 R8 1.54K 1 2 R9 1.54K 1 2 R10 6.2K + C171010V20%Tant. C190.06850V C200.02250V C250.02250V C26.1050V 1 2 R20 634K 1 A 2 C 4 COLL 3 EMIT U7 TLP421(GR) 1 2 R15 620 12 R74991% WP3 WP4 WP5 WP6 WP7 CW 1 2 3 R26 500K 2 V2P 3 V2N 5 V1P 4 V1N 6 AGND 7 REF 16 F1 15 F2 14 CF 12 REVP 11 RCLKIN 13 DGND 10 S0 9 S1 8 SCF U4 AD71056ARZ C30.10 C294.710V20% NTC1470 Ohm 1 2 R38 95.3 1% 12 R392261% 1 2 R19 634K +3.3V WET_PROBE RF_CHASSIS_GND RF_CHASSIS_GND UNREG_DC +5V_WM RF_CHASSIS_GND L1 L2 L2_RETURN L1L2 +5V_WM LEAK_DETECT WATT_METER BROWN_OUT_DETECT

SHEET: OF SCH, NEXT GEN XPNDR 12/19/2006 4 PB0988P01 N/A C Tubbs Environment One Corporation <Checked By> <QC By> <Released By> <Checked Date><QC Date><Release Date> <Code> B 11 REV: SIZE: CODE: DRAWN: DATED: DATED: CHECKED:QUALITY CONTROL: DATED: DATED: RELEASED: COMPANY:TITLE: DRAWING NO: SCALE: REVISION RECORD APPROVED: ECO NO: ABD DATE: 1 2 3 4 5 6 DCAB C LTR HIGH LEVEL ALARM SWITCH ON/OFF SWITCH 6 8-BYPASS 9 A 10 B 11 C 12 D 2 RST 14 OSC_INH 15 MONO-IN 1 SET 7 CLK_INH 3 IN1 4 OUT1 5 OUT2 13 DEC_OUT U1 MC14536B 12 R83.3M 1 2 R3 1M 12 R2180K C10.001uF G D S Q1 2N7002-7-F 12 R910 C31.0uF Tant. + K A D4MM3Z5V1T15.1V, 200mW L1 9mH2% 12 R1100K C682pF1% WP2WP4 12 R4100K 12 R7100K 12 R6100K 12 R53.3M C4100pF1% C5N.I. WP1WP3 D3 MMBD4148W D5 MMBD4148W D2 MMBD4148W D6 MMBD4148W C2 0.1 50V 12 R101M D1MMBD4148W +5V +5V +5V+5V

Underwriters Laboratories Inc. A not-for-profit organization dedicated 1285 Walt Whitman Rd. to public safety and committed to Melville, NY 11747 quality service for over 100 years Tel: (631) 271-6200 Fax: (631)439-6095 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, NY 11747 www.ul.com/emc 631-271-6200 Project: 07ME02442 File: MC15007 Date: March 23, 2007 Model: NEXTGen FCC ID: U8X-NB0024GXX Electromagnetic Compatibility Test Report For Environment One Corporation Copyright  2005 Underwriters Laboratories Inc. Underwriters Laboratories Inc. authorizes the above-named company to reproduce this Report provided it is reproduced in its entirety. Only those products bearing the UL Mark should be considered as being covered by UL. Project Number: 07ME02442 File Number MC15007 Page 2 of 34 Model Number: NEXTGen FCC ID: U8X-NB0024GXX Underwriters Laboratories Inc. 1285 Walt Wh…

Text truncated - open the document above for the full version.