UO3-UN1CXCDrivecam Event Recorder

©2022 Lytx, Inc. - Confidential & Proprietary. Page 1 of 45 (North America Edition) Lytx ® SF-Series Event Recorder Installation Instructions (North America Edition) Last updated: 2022 November 14 THE DEVICE SHOULD BE INSTALLED AND MAINTAINED BY QUALIFIED TECHNICIANS. Only a properly qualified technician should install and maintain the SF-Series device(s). Any electrical work should be performed only by an MECP-certified or equivalent technician with an expertise in installing and troubleshooting advanced vehicle onboard components including multiplexed circuits. Lytx, Inc. disclaims all responsibility for any damages arising from improper installation and maintenance of the SF-Series device(s). This guide is protected as confidential and proprietary information of Lytx, Inc. Copying and use of this guide for any purpose other than installing SF-Series devices in vehicles of Lytx, Inc.’s customers is expressly prohibited. Information contained in this guide was in effect as of the date set forth above and is subject to change without notice or liability. Lytx, Inc. reserves the right to revise the information presented or to discontinue the production of parts described at any time. ©2022 Lytx, Inc. - Confidential & Proprietary. Page 2 of 45 (North America Edition) Contents Safety Instructions ............................................................................................................................................. 3 Device Installation Overview ............................................................................................................................. 7 Installation Warnings ............................................................................................................................................. 7 Before You Begin ........................................................................................................................................................... 7 Materials ................................................................................................................................................................... 8 Required Tools ..................................................................................................................................................... 11 Optional Tools ....................................................................................................................................................... 11 Optional Parts ....................................................................................................................................................... 11 Device Features ................................................................................................................................................... 12 SF-Series Installation Procedures ................................................................................................................. 13 Pre-Installation Vehicle Check ................................................................................................................................ 13 Mount the Bracket and Event Recorder ................................................................................................................ 13 Mounting Preparation ......................................................................................................................................... 13 Attach the Bracket and Event Recorder .......................................................................................................... 16 Connect Electrical Wiring ......................................................................................................................................... 17 Electrical Connection Overview ........................................................................................................................ 18 Wiring and Termination Suggestions for Vehicle Interface Cable ............................................................ 24 Event Recorder Electrical Connections ........................................................................................................... 26 Connect to the Vehicle J1939 Network ........................................................................................................... 28 Connect Turn Signals (ER-SF300/ER-SF400 + J1939 only) ....................................................................... 29 Route the Device Power Cable .......................................................................................................................... 30 Register the Device and Complete Installation ................................................................................................... 31 Complete Installation .......................................................................................................................................... 31 Conduct Final Checks.......................................................................................................................................... 32 Installation of Optional Parts ................................................................................................................................... 33 Overhead Mounting Bracket Installation Procedures .................................................................................. 33 Extended Mounting Arm Installation ............................................................................................................... 35 Remote Push Button Installation ...................................................................................................................... 38 Maintenance & Troubleshooting ..................................................................................................................... 39 Maintenance .............................................................................................................................................…

Text truncated - open the document above for the full version.

Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: Lytx, Inc. FCC ID: UO3-UN1CXC To whom it may concern, Lytx Inc. (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. [Signature] Rajesh Rudraradhya Chief Technology Officer Lytx, Inc. February 14, 2023 DocuSign Envelope ID: D8C3A606-4D1A-4B56-B7BC-E6A8E6AE5448

Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to 47 CFR part §2.911(d)(7) of the FCC rules. To whom it may concern, This letter is to certify that Lytx Inc. (“Applicant”) accepts responsibilities to act as its own agent pursuant to 47 CFR part §2.911(d)(7) of the FCC rules for service of process. I consent to the obligation to accept service of process on behalf of the Applicant for all certification applications to the FCC. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC if there is any change in the status identified above. Applicant Company Name : Lytx, Inc. Lytx FRN : 0015605496 Contact Name : Rajesh Rudraradhya Address : 9785 Towne Centre Dr., San Diego, CA 92121 United States Telephone No : +1 866-419-5861 Email : [email protected] Signature: ____________________________________ Date: May 4, 2023 DocuSign Envelope ID: BDABB201-75AD-4847-8B2D-D1265A8512E6

November 19, 2022 Attention: Application Examiner RE: Request for Confidentiality Applicant: Lytx Inc. FCC ID: UO3-UN1CXC To Whom It May Concern: Permanent Confidentiality Request is hereby submitted by Lytx, Inc. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:  Schematics  Detailed Block Diagrams  Detailed Operational/Functional Description We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading-edge technology developed by us. Sincerely, Rajesh Rudraradhya Chief Technology Officer DocuSign Envelope ID: 06CB46F5-6606-439B-8300-9CB36FFD8BCC

May 3, 2023 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Lytx Inc. FCC ID: UO3-UN1CXC Lytx FRN: 0015605496 To Whom It May Concern: We, Lytx, Inc., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number UO3-UN1CXC under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is November 19, 2022. The Limited Agency Agreement expires on May 19, 2023, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] Rajesh Rudraradhya Chief Technology Officer DocuSign Envelope ID: 4218E62A-6A7A-4978-9EEC-B6665AB5E627

U-NII Client in Non-Associated Mode February 20, 2023 Attention: Application Examiner RE: U-NII Client in Non-Associated Mode Applicant: Lytx, Inc. FCC ID: UO3-UN1CXC To Whom It May Concern: We, Lytx, Inc., declare that our DriveCam Event Recorder DC-7000-002 operates under the definition of a DFS client device without radar detection. The client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. Sincerely, Rajesh Rudraradhya Chief Technology Officer DocuSign Envelope ID: 6228EB52-821E-42F9-B9F8-21B7F240E9BB

Top Side View Front Side View Back Side View Left Side View Right Side View Bottom Side View

FCC ID: UO3-SFEG95NAX

Main Board Communication Board Note: Ethertronics part number P822601 are LTE antennas

LYTX, INC. RF Exposure Exhibit SCOPE OF WORK EMC TESTING – Drivecam Event Recorder Model: DC-7000-002 REPORT NUMBER 105146268MPK-009 ISSUE DATE December 12, 2022 REVISED DATE April 24, 2023 PAGES 10 DOCUMENT CONTROL NUMBER Non-Specific Radio Report Shell Rev. December 2017 MPK © 2017 INTERTEK Non-Specific Radio Report Shell Rev. December 2017 MPK EMC Report for Lytx, Inc. on the Drivecam Event Recorder Page 2 of 10 RF Exposure Exhibit (mobile devices) Report Number: 105146268MPK-009 Project Number: G105146268 Report Date: April 24, 2023 Product Designation: Model Tested: Drivecam Event Recorder DC-7000-002 FCC ID: UO3-UN1CXC IC: 6778A-UN1CXC to 47CFR 2.1091 RSS-102 Issue 5 for Lytx, Inc Tested by: Client: Intertek 1365 Adams Court Menlo Park, CA 94025 USA Lytx, Inc 9785 Towne Centre Drive San Diego, CA 92121 USA Report prepared by: Report reviewed by: Juan Alapizco Vega / EMC Engineer Minh Ly / EMC Team Lead This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. REPORT NUMBER: 105146268MPK-009 Issued: April 24, 2023 Non-Specific Radio Report Shell Rev. December 2017 MPK EMC Report for Lytx, Inc. on the Drivecam Event Recorder Page 3 of 10 Report No. 105146268MPK-009 Equipment Under Test: Drivecam Event Recorder Model Number(s): DC-7000-002 Applicant: Lytx, I nc. Contact: Stephanie Rydell Address: 9785 Towne Centre Drive San Diego, CA 92121 Country: USA Tel. Number: (858) 380-3012 Email: [email protected] Applicable Regulation: 47CFR 2.1091 RSS-102 Issue 5 Date of Test: December 04, 2022 We attest to the accuracy of this report (Revision 1.0): Report prepared by: Report reviewed by: Juan Alapizco Vega / EMC Engineer Minh Ly / EMC Team Leader We attest to the accuracy of this report (Revision 1.1): Report prepared by: Report reviewed by: Aaron Chang / EMC Team Leader Anderson Soungpanya / EMC Team Leader REPORT NUMBER: 105146268MPK-009 Issued: April 24, 2023 Non-Specific Radio Report Shell Rev. December 2017 MPK EMC Report for Lytx, Inc. on the Drivecam Event Recorder Page 4 of 10 TABLE OF CONTENTS LYTX, INC. ....................................................................................................................................................... 1 1.0 RF Exposure Summary ................................................................................................................... 5 2.0 RF Exposure Limits ........................................................................................................................ 5 3.0 Test Results (Mobile Configuration) ............................................................................................. 7 4.0 Document History ......................................................................................................................... 10 REPORT NUMBER: 105146268MPK-009 Issued: April 24, 2023 Non-Specific Radio Report Shell Rev. December 2017 MPK EMC Report for Lytx, Inc. on the Drivecam Event Recorder Page 5 of 10 1.0 RF Exposure Summary Test Reference FCC Reference Industry Canada Result Radio frequency Radiation Exposure Evaluation 47 CFR§2.1091 RSS-102 Issue 5 Complies 2.0 RF Exposure Limits In this document, we evaluate the RF Exposure to human body due the intentional transmission from the transmitter (EUT). The limits for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 and RSS-102 are fol lowed. 2.1 FCC Limits According to FCC 1.1310 table 1: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 0.3 – 3.0 614 1.63 *100 6 3.0 – 30 1842/f 4.89/f *900/f 2 6 30-300 61.4 0.163 1.0 6 300 - 1500 ... ... F/300 6 1500 - 100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 0.3 – 1.34 614 1.63 *100 30 1.34 – 30 824/f 2.19/f *180/f 2 30 30 – 300 27.5 0.073 0.2 30 300 - 1500 ... ... F/1500 30 1500 - 100,000 ... ... 1.0 30 F = Frequency in MHz * = plane wave equivalent density REPORT NUMBER: 105146268MPK-009 Issued: April 24, 2023 Non-Specific Radio Report Shell Rev. December 2017 MPK EMC Report for Lytx, Inc. on the Drivecam Event Recorder Page 6 of 10 2.2 Industry Canada Limits According to RSS-102, Industry Canada has adopted the SAR and RF field strength limits established in Health Canada’s RF exposure guideline, Safety Code 6. Table 4: RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) Frequency Range Electric Field Magnetic Field Power Density Reference Period (MHz) (V/m rms) (A/m rms) (W/m 2 ) (minutes) 0.003-10 83 90 - Instantaneous* 0.1-10 - 0.73/ ƒ - 6** 1.1-10 87/ ƒ 0.5 - - 6** 10-20 27.46 0.0728 -2 6 20-48 58.07/ ƒ 0.25 0.1540/ ƒ 0. 25 8.944/ ƒ0.5 6 48-300 22.06 0.05852 1.291 6 300-6000 3.142 ƒ 0.3417 0.008335 ƒ 0.3417 0.02619 ƒ 0.6834 6 6000-15000 61.4 0.163 10 6 15000-150000 61.4 0.163 10 616000/ ƒ 1.2 150000-300000 0.158 ƒ 0.5 4.21 x 10-4 ƒ 0.5 6.…

Text truncated - open the document above for the full version.

Ethertronics’ Stamped Metal series of Isolated Magnetic Dipole™ (IMD) antennas deliver on the key needs of device designers for higher functionality and performance in smaller/thinner designs. These innovative antennas provide compelling advantages for full WIFI dual-band enabled handheld devices, media players and other mobile devices. Greater Flexibility Ethertronics’ first-in-class IMD technology enables you to develop concept designs that are more advanced and that deliver superior performance in reception critical applications. DATASHEET Part No. 1004454 Product: Wi-Fi / BT / WLAN / ZigbeeEmbedded Stamped Metal Antenna 8/12/2019Proprietary www.ethertronics.com Electrical Specifications Typical Characteristics, on 120 x 180 mm PCB Part No. 1004454 WLAN / BT / ZigbeeEmbedded Stamped Metal Antenna 2.4 / 5.2 / 5.8 GHz (802.11 a/b/g/n/c + Japan) Supports: Wi-Fi applications, Agriculture, Automotive, Bluetooth, Zigbee, WLAN, Smart Home, Healthcare, Digital Signage Wi-Fi Dual Band Stamped Metal Embedded Antenna 2.4 GHz; 5 GHz KEY BENEFITS Stay-in-Tune Ethertronics antenna technology provides superior RFfield containment, resulting in less interaction with surrounding components. Quicker Time-to-Market By optimizing antenna size, performance and emissions, customer and regulatory specifications are more easily met. Reliability Products are the latest RoHS version compliant •Embedded design •Cellular, Headsets, Tablets •Gateway, Access Point •Handheld •Telematics •Tracking •Healthcare •M2M, Industrial devices •Smart Grid •OBD-II APPLICATIONS Frequency2400–2485 MHz5100 –5825 MHz Peak Gain 2.7 dBi4.8 dBi Average Efficiency74%67% VSWR Match1.4:1 max1.7:1 max Feed Point Impedance50 ohms unbalanced PolarizationLinear Power Handling0.5 Watt CW Ordering Part Number1004454 Size (mm)17.85 x 6.9x 4.3 Mounting SMT Weight (grams)0.48 Packaging Tape & Reel, 1004454 –5,000 pieces per reel Demo Board1004454-01 Mechanical Specifications & Ordering Part Number © 2018 Ethertronics tel +(1) 858.550.3820 | fax +(1) 858.550.3821 email: [email protected] 5501 Oberlin Drive, Suite 100 San Diego, CA 92121 -USA Antenna Dimensions Typical antenna dimensions (mm) Top View PinDescription 1 Feed 2 Ground 3 Dummy Pad Part NumberA (mm)B (mm)C (mm) 100445417.85 ±0.36.9 ±0.34.3 ±0.4 Height Pin #1 2.4 / 5 GHz Ethertronics’ Embedded Antenna Specifications Ethertronics produces a wide variety of standard and custom antennas to meet user needs. DATASHEET | Part No. 1004454 Front View Bottom View Pin #2 Pin #3 A B C © 2018 Ethertronics tel +(1) 858.550.3820 | fax +(1) 858.550.3821 email: [email protected] 5501 Oberlin Drive, Suite 100 San Diego, CA 92121 -USA VSWR and Efficiency Plots Typical Performance on 120 x 180 mm PCB Low Band VSWRHigh Band VSWR Low Band EfficiencyHigh Band Efficiency 2.4 / 5 GHz Ethertronics’ Embedded Antenna Specifications Ethertronics produces a wide variety of standard and custom antennas to meet user needs. DATASHEET | Part No. 1004454 1004454 Antenna Mounted using 1000418 120mm 180mm 100mm U.FL cable © 2018 Ethertronics tel +(1) 858.550.3820 | fax +(1) 858.550.3821 email: [email protected] 5501 Oberlin Drive, Suite 100 San Diego, CA 92121 -USA Antenna Radiation Patterns Typical Performance on 120 x 180 mm PCB Measured @ 2400, 5100 MHz Measured at 2400 MHz Measured at 5100 MHz 2.4 / 5 GHz Ethertronics’ Embedded Antenna Specifications Ethertronics produces a wide variety of standard and custom antennas to meet user needs. DATASHEET | Part No. 1004454 X Z Y © 2018 Ethertronics tel +(1) 858.550.3820 | fax +(1) 858.550.3821 email: [email protected] 5501 Oberlin Drive, Suite 100 San Diego, CA 92121 -USA Pin Descriptions Pin#Description 1 Feed 2 Ground 3 Dummy Pad Pin #1 2.4 / 5 GHz Ethertronics’ Embedded Antenna Specifications Ethertronics produces a wide variety of standard and custom antennas to meet user needs. DATASHEET | Part No. 1004454 Antenna Outline 50Ω Transmission line Pin #3 Pin #2 P1 S1 P2 1 2 3 P2 S1 P1 R4R5 R6 R1 R2 R3 50ohm (Antenna Matching) R1 R2 R3 R4 R5 R6 P1S1P2R1–R3R4–R6 Default ValuesDNI0ΩDNIDNIDNI Component ToleranceN/AN/AN/AN/AN/A PIN Antenna Layout (Minor Tuning Layout) Typical layout dimensions (mm) Antenna Matching & Tuning Component Values Note: Layout has minor tuning capabilities to allow for small antenna footprint. Antenna Outline •Additional VIAS: Diam. 0.2mmto be placed around antenna, (no viason transmission lines). •Via holes must be covered by solder mask © 2018 Ethertronics tel +(1) 858.550.3820 | fax +(1) 858.550.3821 email: [email protected] 5501 Oberlin Drive, Suite 100 San Diego, CA 92121 -USA Antenna Layout (Major Tuning Layout) Typical layout dimensions (mm) Antenna Outline Antenna Outline Pin Descriptions Pin#Description 1 Feed 2 Ground 3 Dummy Pad 50Ω Transmission line Pin #3 Pin #2 Pin #1 2.4 / 5 GHz Ethertronics’ Embedded Antenna Specifications Ethertronics produces a wide variety of standard and custom antennas to meet user needs. DATASHEET | Part No. 1004454 Note: Layout has Major tuning capabilities to allow for robust tuning after board spin, instructions on Antenna Matching Structure page. •Additional VIAS: Diam. 0.2mmto be placed around antenna, (no viason transmission lines). •Via holes must be covered by solder mask © 2018 Ethertronics tel +(1) 858.550.3820 | fax +(1) 858.550.3821 email: [email protected] 5501 Oberlin Drive, Suite 100 San Diego, CA 92121 -USA P1S1P2R1–R3R4–R6R7–R14R15 -R20 Default Values DNI0ΩDNIDNIDNIDNIDNI Tolerance N/AN/AN/AN/AN/AN/AN/A Pin#Description 1 Feed 2 Ground 3 Dummy Pad Pin Descriptions DATASHEET | Part No. 1004454 Antenna Matching Structure (Major Tuning Structure) Typical matching values on 140 x 50 mm PCB 2.4 / 5 GHz Ethertronics’ Embedded Antenna Specifications Ethertronics produces a wide variety of standard and custom antennas to meet user needs. Low Band Tuning (Add to Shift Low) [R4] [R5][R6] [ R1 ] [ R2 ] [ R3 ] [P1] [P2] [ S1 ] [ R15 ] [ R16 ] [ R17 ] [ R18 ] [ R19 ] [ R20 ] [R7][R8] [R9][R10] [R11][R12] [R13] [R14] …

Text truncated - open the document above for the full version.

EMC Report for Lytx,Inc on Drivecam Event Recorder File: 105146268MPK-006Page 1 of 201 TEST REPORT Report Number: 105146268MPK-006 Project Number: G105146268 Report Issue Date: October 29, 2022 Report Revision Date: April 10, 2023 Testing performed on the Drivecam Event Recorder Model Number: DC-7000-002 FCC ID: UO3-UN1CXC IC: 6778A-UN1CXC to FCC Part 15 Subpart E (15.407) Industry Canada RSS-247, Issue 2 For Lytx, INC. Test Performed by:Test Authorized by: Intertek 1365 Adams Court Menlo Park, CA 94025 USA Lytx, Inc 9785 Towne Centre Drive San Diego, CA 92121 USA Prepared by: Date:October 29, 2022 Juan Alapizco Vega Reviewed by:Date:October 29, 2022 Minh Ly This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. This report must not be used to claim product endorsement by A2LA, NIST nor any other agency of the U.S. Government. EMC Report for Lytx,Inc on Drivecam Event Recorder File: 105146268MPK-006Page 2 of 201 Report No. 104452230MPK-006 Equipment Under Test:Drivecam Event Recorder Model Number:DC-7000-002 Applicant:Lytx, Inc. Contact: Stephanie Rydell Address: 9785 Towne Centre Drive San Diego, CA 92121 Country:USA Tel. Number:(858) 380-3012 Email:[email protected] Applicable Regulation: FCC Part 15 Subpart E (15.407) ISED RSS-247 Issue 2 Date of Test: August 16, 2022 to October 11, 2022 We attest to the accuracy of this report 1.0: Juan Alapizco Vega EMC Engineer Minh Ly EMC Team Lead We attest to the accuracy of this report 1.1: Aaron Chang EMC Team Leader Anderson Soungpanya EMC Team Leader EMC Report for Lytx,Inc on Drivecam Event Recorder File: 105146268MPK-006 Page 3 of 201 TABLE OF CONTENTS 1.0 Introduction ............................................................................................................................... 5 1.1 Summary of Tests ............................................................................................................... 5 2.0 General Description ................................................................................................................... 6 2.1 Product Description ............................................................................................................ 6 2.2 Related Submittal(s) Grants ................................................................................................ 7 2.3 Test Methodology ............................................................................................................... 7 2.4 Test Facility ......................................................................................................................... 7 2.5 Measurement Uncertainty ................................................................................................. 7 3.0 System Test Configuration ......................................................................................................... 8 3.1 Support Equipment ............................................................................................................. 8 3.2 Block Diagram of Test Setup ............................................................................................... 8 3.3 Justification ....................................................................................................................... 11 3.4 Mode of Operation During Test ........................................................................................ 11 3.5 Modifications required for Compliance ............................................................................ 13 3.6 Additions, deviations and exclusions from standards ...................................................... 13 4.0 Measurement Results .............................................................................................................. 14 4.1 Emission Bandwidth and 99% Occupied Bandwidth ........................................................ 14 4.1.1 Requirement ........................................................................................................ 14 4.1.2 Procedure............................................................................................................. 14 4.1.3 Test Result............................................................................................................ 15 4.2 Maximum Conducted Output Power & Power Spectral Density ...................................... 70 4.2.1 Requirement ........................................................................................................ 70 4.2.2 Procedure............................................................................................................. 71 4.2.3 Test Results .......................................................................................................... 72 4.3 Transmitter Radiated Emissions ..................................................................................... 126 4.3.1 Requirement ...................................................................................................... 126 4.3.2 Procedure........................................................................................................... 127 4.3.3 Field Strength Calculation…

Text truncated - open the document above for the full version.

EMC Report for Lytx,Inc on Drivecam Event Recorder File: 105146268MPK-006 Page 71 of 201 4.2.1.2 Requirement (RSS-247; 6.2) Frequency band 5150-5250 MHz LE-LAN devices are restricted to indoor operation only in the band 5150-5250 MHz. The maximum e.i.r.p. shall not exceed 200 mW o…

Text truncated - open the document above for the full version.