UYQGUANLIFMTRANSMITTER

GUANLI FM TRANSMITTER USER MANUAL Read this manual carefully before using DANGER: Procedures which may lead to dangerous condition and cause death or serious injury to the user if not carried out properly. WARNING: Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out probability of superficial injury or physical damage is high. CAUTION: Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if not carried out properly. Supervision is highly recommended when children 14 years or under are using this system. FLYING ATTENTION 1. Do not fly simultaneously on the same frequency. Use of the same frequency will cause interference even if the modulation method (AM, FM, PCM) is different. 2. Do not fly on rainy or windy days, or at night. Water will penetrate into the transmitter and cause faulty operation, or loss of control, and cause a crash. 3. Extend the antenna to its full length. If the antenna is too short, the effective range of the radiowaves will be come shorter. 4. Always test the digital proportional R/C set before use. Check that the direction of operation of each servo matches the operation of its control stick. If a servo does not move in the proper direction, or operation is abnormal, do not fly the plane. NAME AND HANDLING OF EACH PART Note: The crystal is fixed and cannot be accessed by the end USER! TRANSMITTER OPERATION AND MOVEMENT OF EACH SERVO 1CH—AILERON OPERATION: The aileron stick use to tilt the plane to left or right. To level the plane, the aileron sick must be moved in the opposite direction. When the aileron stick is tilted and held, the plane will roll. 2CH—ELEVATOR OPRATION: When the elevator stick is pulled back, the plane climbs (UP operation). When the elevator is lowered, the plane dives (DOWN operation). 3CH—THROTTLE OPERATION: When the throttle stick is pulled back, the engine throttle lever arm move to the slow (low speed) side. When the throttle stick is pushed forward, the throttle lever arm moves to the HIGH (high speed) side. 4CH—RUDDER OPERATION: When the rudder stick is moved to the right, the rudder moves to the right and the nose points to the right, relative to the direction of flight. When the rudder stick is moved to the left, the rudder moves to the left and the nose points to the left and the direction of travel of the plane changes. FUNCTIONS INTRODUCE: MAIN FUCTION 1. STANDARD 4CH FUCTION 2. Servo reversing for channel 1, 2, 3, and 4 3. When the voltage of battery is lower than 8.4V, the warning light on radio will flash and beeping noise is given out. WARNING: • Any unauthorized adjustment on this product could result in a violation of part 95 of the FCC Rules. Please have a person certified as technically qualified to perform transmitter maintenance and repair duties in the private land mobile services and fixed services by an organization or committee representative of users of the services. • Replacement of any transmitter component (crystal, semiconductor, etc.) could result in a violation of part 95 of the FCC Rules. • A license may be required to operate this product in some countries. Consult about the license issue from the radiology department of the country. • Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment. Any change to the equipment will void FCC grant. NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 95 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.

(72.870MHz) mirco-computersystemcoder functionoperation ket code to outputouput the pulse 850-20335Usmodulation.modulat the way to ppm RF--VCO Times frequency quartz crystal14.483MHz Through 5 timesfreuencies selectby examinationsthe strang time72.415MHz The powerenglarge the frequency ofselect byexaminationsing buenglared by hightransistor,againthough the fieldeffect englrge tooutput 500mW power chose thefrequency network passed the many L,Cnatch an electriccircuit select byeaxmination thefrequency72.415MHz,repress thehigh frequency,andpromote the powerthe validity develop antenna the signals send outsfrom the antenna,-7increasing of BDsbenefit Block Diagram

EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2

EXHIBIT 1- PRODUCT LABELING Proposed FCC ID Label Format FCC ID: UYQGUANLIFM Specifications: Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

EXHIBIT 1- PRODUCT LABELING Proposed FCC ID Label Format FCC ID: UYQGUANLIFM Specifications: Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 Solder Board-Component View 1 Solder Board-Component View 2

OPERATION DISCRIPTIONS The fictional signal analyzed by the micro-computer system coder which gets a pulse modulation of 850-20335Us then passing through the RF-VCO working with 14.483MHz crystal for producing a FM carrying signal. Then multiplied by the time frequency circuit. Carrying Wave amplified by the amplifier circuit unit, through the wideband LC filter and transmitting circuit and antenna, then transmit out as 72.870MHz. 1. Functional operation kit deals with the functional controlling. 2. Micro-computer system coder is the main functional control center, working with 14.483MHz crystal, deal with Faction function control and other state indication. 3. Time frequency is a multiplied frequency to produce a extract HF signal. 4. RF-VCO is a FM Module for producing FM CW. 5. The power enlarger is function on enlarge the output power. 6. There is no receiving function since it is a one-side band transmitting module.

Product TRANSMITTER Model GUANLI FM ItemSpecifcationQuantityLabelNote 1GL603 167X47X1.6mm1PCS72mhz94VO 2P458DIP201PCSic 378L05TO-92B1PCSW1 4 Diode 1N4001,1W2PCSD1 5 Diode B910,TO-92B1PCSD2 6 Diode 4v70.5W1PCSD3 7 Audion D400TO-92L1PCSQ61.5A 8 Audion 9014TO-922PCSQ2Q3 9 Audion 9018HTO-922PCSQ4Q5 10 Resistor 1K5±5% 1/8W1PCSR23 11 Resistor 1±5% 1/8W1PCSR32 12 Resistor 2K2±5% 1/8W2PCSR25R27 13 Resistor 2K±5% 1/8WPCSR1R2 14 Resistor 4K7±5% 1/8W1PCSR3R4R6 15 Resistor 5K6±5% 1/8W1PCSR11 16 Resistor 10K±5% 1/8W10PCS R5.7.8.9.1 0.12.16.1 6.36.37 17 Resistor 20K±5% 1/8W1PCSR38 18 Resistor 22±5% 1/8W2PCSR24R26 19 Resistor 33K±5% 1/8W1PCSR15 20 Resistor 68±5% 1/8W1PCSR30 21 Resistor 220±5% 1/8W1PCSR31 22 Resistor 220k±5% 1/8W2PCSR21 23 Resistor 330±5% 1/8W1PCSR28R18 24 Resistor 390±5% 1/9W1PCSR22 25 Resistor 680±5% 1/8W1PCSR19 26 Capacitor 2.2UF/50V±20%,MINI1PCSE2 27 Electrolytic Capacitor 100UF/25V±20%,MINI2PCSE3E4 28 Terylene Capacitor 102PF/25V±20%3PCSC13.14.15 29 Ceramic Capacitor 15pF/50V±10%,3PCSC22.24.27 30 Ceramic Capacitor 20pF/50V±10%,2PCSC8C9 31 Ceramic Capacitor 27PF/50V±10%,1PCSC29 Product TRANSMITTER Model GUANLI FM ItemSpecifcationQuantityLabelNote 32 Ceramic Capacitor 40pF/50V±10%,3PCSc32.20.19 33 Ceramic Capacitor 82PF/50V±10%,1PCSc30 34 Ceramic Capacitor 103pF/50V±20%,5PCS c10.17.18. 21.45 35 Ceramic Capacitor 104pF/50V±20%,9PCS c40.1.7.13 .5.11.4.41 .6 36 Ceramic Capacitor 501PF/50V±20%,1PCSc26 37 Colour-code Inductor 10UH±10%,3*71PCSL2 38 Variometer 1.2UH,Z1952892PCST3T4 39 Rheostat 014,Z1953012PCST1T2 40 Ceramic Crystal 4.0M,DIP2.20PPM1PCSX1 41 Buzzer Φ11X 13,DC5V1PCS 42 Crystal Holder 1PCS 43 Crystal 13.4033MHz,HC-50U1PCS40MHZ 44 Antenna Φ7.0+154,L=9501PCSANT 45 varistor 16J171-B5K15F,65°4PCS 46 varistor FRB067-5K1PCS 47Φ5,1PCSRED 48Φ5,1PCSGREEN 49 Jump Wire 3+10+3MM,Φ0.86PCS :: 50DC-0211PCS 51 switch SS-12F32G125PCS 52 Lead Wire UL1007#26 53 Red Cord 3+150+3MM2PCS 54 Black Cord 3+150+3MM2PCS 55 Black Cord 3+30+3MM1PCS 56 Array Cord 57 58 White Cord 40M 3+150+3MM2PCS Product TRANSMITTER Model GUANLI FM ItemSpecifcationQuantityLabelNote 59 60 61 62 63 64 65 66 DC Plug 1PCS 671.5m1PCS 68 69 70 71 72 73 74 3+200+3MM2PCS 3+110+3MM1PCS

APPLICANT: ZHONGSHAN GUANLI MODEL FACTORY FCC ID: UYQGUANLIFM The unit has no provisions for tuning.

ANTENNA 72MHz K1 12v B910 100UF/25V 78L05 10K 12 3 GUANLI FM SKYSPORT4 RED 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 1234 8765 12MM T3 T4 T5 27p B5K GREEN 104 72MHZ DC-021 IC1458 W1 E3 C38 C21 X2 ANT1 10k B5K B5K B5K B5K mix2-4or1-6 1234 8765 SW T2 T1 D11N4001 C41104 C1 104 E1 100UF/16V C10 103 R1 2K R22K R3 4K7 R4 4K7 R5 10k R6 4K7 R37 10K R38 20K E22.2uf C5104 C6 104 C7104 C4104 R710K R810K X1 4.0MHZ C8 20P C9 20P R9 10K R36 10K R1010K R115K6 C11 104 C13104 R1210K Q2 9014 R1533KR1610KR1710K C15 102 Q39014 C14 102 C16102 R19 680 R18330 C18 103 D34V7 E4 100UF C40104 C17103 R21220K C19 40P C20 40P R22390 Q4 9018 C2215 C232 C2415 C26501 R2422 C21103 R231K5R252K2 Q5 9018 R30 68 C30 82 R28330 C27 15 R2622 C45103 C2940 R272K2 R31220 R32 1 C32103 Q6 D40 L210uh C3240

ZHONG SHAN GUANLI MODEL FACTORY MODEL: GUANLI FM REPORT NO.: STR07018030I PAGE 1 OF 14 FCC PART 95 FCC PART 95 MEASUREMENT AND TEST REPORT FOR ZHONG SHAN GUANLI MODEL FACTORY XiShan industry zone, SanXiang town, Zhongshan, Guangdong, China FCC ID: UYQGUANLIFM Report Concerns: Original Report Equipment Type: TRANSMITTER Model: GUANLI FM Report No.: STR07018030I Test/Witness Engineer: Innaz Lee Test Date: 2007-01-24 Prepared By: Shenzhen SEM.Test Compliance Service Co., Ltd Room 609-610, Baotong Building, Baomin 1 st Road, Baoan District, Shenzhen, Guangdong, P.R.C. (518133) Approved & Authorized By: Jandy So / PSQ Manager Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by SEM.Test Compliance Service Co., Ltd . ZHONG SHAN GUANLI MODEL FACTORY MODEL: GUANLI FM REPORT NO.: STR07018030I PAGE 2 OF 14 FCC PART 95 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)...............................................................................3 1.2 TEST STANDARDS..................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S) .......................................................................................................................3 1.4 TEST METHODOLOGY............................................................................................................................................4 1.5 TEST FACILITY.......................................................................................................................................................4 1.6 EUT EXERCISE SOFTWARE....................................................................................................................................4 1.7 ACCESSORIES EQUIPMENT LIST AND DETAILS.......................................................................................................4 1.8 EUT CABLE LIST AND DETAILS.............................................................................................................................4 2. SUMMARY OF TEST RESULTS ...........................................................................................................................5 3. §2.1046 AND §95.639(B) (3) - RF OUTPUT POWER............................................................................................6 3.1 STANDARD APPLICABLE........................................................................................................................................6 3.2 TEST EQUIPMENT LIST AND DETAIL.......................................................................................................................6 3.3 TEST PROCEDURE...................................................................................................................................................6 4.4 ENVIRONMENTAL CONDITIONS..............................................................................................................................7 3.4 TEST RESULT/PLOTS..............................................................................................................................................7 4. §2.1049 AND § 95.633(B) - OCCUPIED BANDWIDTH OF EMISSION ............................................................8 4.1 STANDARD APPLICABLE........................................................................................................................................8 4.2 TEST EQUIPMENT LIST AND DETAILS.....................................................................................................................8 4.3 TEST PROCEDURE...................................................................................................................................................8 4.4 ENVIRONMENTAL CONDITIONS..............................................................................................................................9 4.5 TEST RESULTS/MASKS...........................................................................................................................................9 5. §95.635(B)(1), §95.635(B)(3), §95.635(B)(7), §95.635(B)(10), §95.635(B)(11), §95.635(B)(12)- RADIATED SPURIOUS EMISSION ..............................................................................................................................................10 5.1 MEASUREMENT UNCERTAINTY............................................................................................................................10 5.2 STANDARD APPLICABLE......................................................................................................................................10 5.3 TEST EQUIPMENT LIST AND DETAILS...................................................................................................................10 5.4 TEST PROCEDURE.................................................................................................................................................11 5.5 ENVIRONMENTAL CONDITIONS............................................................................................................................11 5.6 SUMMARY OF TEST RESULTS/PLOTS....................................................................................................................11 6. §2.1055, §95.621 AND §95.627(B)- FREQUENCY STABILITY ........................................................................13 6.1 STANDARD APPLICABLE......................................................................................................................................13 6.2 TEST EQUIPMENT LIST AND DETAILS................................................................................................................…

Text truncated - open the document above for the full version.

EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Radiated Spurious Emission Setup Frequency Stability Test Setup