V72AE11OWWireless Modem

An Arcadian Networks Inc. Technical Document AE11G OW WIRELESS MODEM UNIT User Guide Version: 102 P/N: 3BRXXXX - 2 - AE11GOW WMU User’s Guide Copyright and Trademark Information: © 2008 Arcadian Networks Inc. All rights reserved. Arcadian Networks Inc. reserves the right to alter the equipment specifications and descriptions in this publication without prior notice. No part of this publication shall be deemed part of any contract or warranty unless specifically incorporated by reference into such contract or warranty. The information contained herein is merely descriptive in nature, and does not constitute a binding offer for the sale of the product described herein. Any use of the Arcadian Networks Inc. logo or trademarks is forbidden without prior written approval from Arcadian Networks Inc. All trademarks mentioned herein are the property of their respective owners. Arcadian Networks Inc.’s trademarks include, but are not limited to, “Arcadian Networks” and “Wireless liberty for all.” - 3 - AE11GOW WMU User’s Guide FCC COMPLIANCE STATEMENT NOTE: This equipment is authorized under FCC ID:V72AE11OW to operate in the A Block of the Upper 700 MHz Band pursuant to Part 27 of the FCC’s rules. In addition, this equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning! Changes or modifications to this equipment not expressly approved by Arcadian Networks, Inc. could void the user’s authority to operate the equipment. - 4 - AE11GOW WMU User’s Guide Installation and Safety Information The following information is provided to ensure safe operation of this equipment. Arcadian Networks assumes no liability in the event that the customer fails to comply with the following safety precautions and warnings. DC System Power-on 1- When connecting the DC power lines, make sure to connect the Ground line first. 2- When disconnecting the DC power lines, make sure to disconnect Ground last. 3- FUSE Replacement: Make sure to use a fuse of the same type and value! 4- EUT shall be powered from limited power source up to 100VA according UL 60950-1 requirements. L’équipement sous tension doit être branché a une source limitée au maximum de100 VA conformément a UL 60950-1. 5- Voltage rating is 12 VDC La tension d’opération est à 12 VDC. Earthing The minimum cross sectional area of the protective earthing should be 1mm 2 . La section du fil de terre doit être d’un minimum 1mm 2. Cables The power, Ethernet and RS232 cables shall be limited up to 140 Feet (42.6 meter). Les branchements électriques, Ethernet & RS232 doivent être limités a un maximum de 140 pieds (42.6 mètres) Repair Safety Repairs of modem should take place only in Arcadian Networks service laboratories or in service laboratories of other Arcadian Networks formally approved distributors. In case of field handling, disconnect the unit from power supply for safest repair. - 5 - AE11GOW WMU User’s Guide Safety Summary Warnings: Carefully connect units to the supply circuit so that wiring is not overloaded. Connect the Ground first (and remove Ground last when disconnecting). Read the installation instructions before connecting the system to its power source. Secure all power cabling when installing this unit. Do not touch the power supply when the power cord is connected. Line voltages are present within the power supply, even when the power switch is off and the power cord is connected. Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects heat up when connected to the power and ground. This can cause serious burns or weld the metal object to the terminals. - 6 - AE11GOW WMU User’s Guide CONTENTS 1 Overview and Purpose....................................................7 1.1 Purpose of This User’s Guide ...........................................7 1.2 Target Audience ................................................................7 1.3 Document Conventions .....................................................8 1.4 Arcadian Networks ............................................................9 2 AE11G OW description ...................................................10 2.1 Overview............................................................................10 2.2 IP Encapsulation Bridge ....................................................11 2.3 VPN module ......................................................................11 2.4 Housing..............................................................................11 2.5 Right Panel Connectors ....................................................13 2.6 Left Panel Connectors .......................................................15 3 Using the Modem.............................................................16 4 Technical Specifications ................................................17 5 Troubleshooting ..............................................................19 5.1 Local troubleshooting ........................................................19 5.2 Remote troubleshooting ....................................................19 6 References .......................................................................20 6.1 General documentation .....................................................20 6.2 FCC documentation...........................................................20 7 Warranty Information .............................…

Text truncated - open the document above for the full version.

tel: 650-726-1263 fax: 650-726-1252 [email protected] Thomas N. Cokenias EMC &Radio Approvals Test & Consulting Services for Commercial, Military, International Compliance P.O. Box 1086 El Granada, CA 94018 email: [email protected] Compliance Certification Services 28 March 2010 47173 Benicia Street Fremont CA 94538 Attention: FCC Application Reviewer RE: Radio Modem Composite Certification Application Part 15 Section: 902-928 MHz FHSS Radio Part 27 Section: 787-788 MHz QPSK/16QAM Radio Applicant: Arcadian Networks FCC ID: V72AE110OW To whom it may concern: The referenced application is for a two-band radio modem. The antennas are not co- located for these devices. The user manual instructs installers to maintain a minimum distance of 60cm between antennas and all persons. RF exposure calculations, derived from MPE distances for the 900 MHz and the 787 MHz transmitters, shows the sum RF exposure at 60cm to be approximately 73% of the allowed maximum. There is a miniPCI slot for a future expansion to the product by the addition of a certified 900 MHz Part 90 module. No modifications will be made to the module, the antenna(s) used will be of the types and gains qualified for use with the radio module. The FCC ID of the future module option is not yet known. For models in the future that incorporate the module, an additional label with the words “Contains FCC ID: XXXyyyy” will be placed on the exterior surface of the radio near the label location shown in this filing. The X and y characters will be replaced with the actual grantee code and unique product descriptor respectively. If you have questions or need further information please contact the undersigned. Sincerely, tel: 650-726-1263 fax: 650-726-1252 [email protected] Thomas N. Cokenias Agent for Arcadian Networks

Arcadian Networks Inc. 400 Columbus Address Suite 210E, Valhalla NY 10595 USA Telephone: 914 579 6300 Fax: 914 579 6301 Date:13 May, 2008 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize THOMAS N COKENIAS, d.b.a. T.N. Cokenias Consulting, to act on our behalf in all manners relating to application for equipment authorization through the Certification Division of Compliance Certification Services (CCS) , including signing of all documents relating to these matters. Any and all acts carried out by THOMAS N COKENIAS on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing THOMAS N COKENIAS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Arnon Afgin General Manager Arcadian Networks Inc

Arcadian Networks Inc. 400 Columbus Address Suite 210E, Valhalla NY 10595 USA Telephone: 914 579 6300 Fax: 914 579 6301 April 6, 2010 Compliance Certification Services Certification Division 47173 Benicia Street Fremont CA 94538 USA Subject: Request for confidentiality for FCC ID: V72AE11OW To Whom it May Concern, In regards the exhibits submitted in support of the application for FCC ID: V72AE11OW, please classify the following as confidential under the provision of 47 CFR 0.459: 1) Schematic diagram 2) RF Functional Block Diagram 3) Operational description 4) Tune-up procedure The above material contains trade secrets or technical data which Arcadian Networks Inc. deems to be proprietary. Therefore this information would customarily be guarded from competitors and cannot be accessible to the general public. If you have questions or need further information please contact the undersigned. Sincerely, T.N. Cokenias Agent for Arcadian Networks Inc.

AE11GOW Pictures Updated: 24 March, 2010 Picture 1: Upper side Picture 2: side 1 (right) Picture 3: Side 2 (left)

Picture 2: side 1 (right)

Picture 4: Open • Lower side, right PCB: RF of 700 MHz radio • Lower side, left PCB: Mother board. The module in the middle of this PCB is optional Licensed 900 MHz module which is FCC modular approved. This TX of this module was not enabled in the tests • Upper side, Left: Core board of 902-928 MHz radio • Upper side , Right: Register board (RF PCB ) of the 902-928 MHz radio Picture 5: RF of 700 MHz radio & Mother board PCB - CS Picture 6: : RF of 700 MHz radio & Mother board PCB - PS Picture 7: RF of 700 MHz radio PCB - CS Picture 8: RF of 700 MHz radio PCB – PS Picture 9: Mother board PCB – CS Picture 10: Mother board PCB – PS Picture 10: Register board (RF) of the 902-928 MHz radio – PS Picture 11: Register board PCB – PS Picture 12: Register board (RF) of the 902-928 MHz radio – PS - removed cover Picture 13: Register board (RF) of the 902-928 MHz radio – PS - removed cover Picture 14: Core board of 902-928 MHz radio – upper side Picture 15: Core board of 902-928 MHz radio – CS (removed cover) Picture 16: Core board of 902-928 MHz radio – PS

Sheet1 A r c a d i a n N e t w o r k s F C C I D : V 7 2 A E 1 1 O W 9 0 2 - 9 2 8 M H z P a r t 1 5 F H S S R a d i o C a l c u l a t e m W / c m 2 h e r e . E n t e r f r e q u e n c y i n M H z : 7 8 7 - 7 8 8 M H z P a r t 2 7 R a d i o R F H a z a r d D i s t a n c e C a l c u l a t i o n Calculation of Limits from 1.1310 Table 1 Controlled Uncontrolled P a r t 1 5 P a r t 2 7 Ave 6 min Ave 30 min m W / c m 2 f r o m T a b l e 1 : 0 . 6 0 0 . 5 2 F(MHz) A A c t u a l F , M H z Occ, mW/c2 Gen, mW/cm2 0.3-3 0.5 100.0 100.0 Max RF Power TX Antenna MPE distance S, mW/cm@ Comment 3.0 - 30.0 5 180.0 36.0 P, dBm G, dBi cm at 20 cm 3 3 0 . 0 - 3 0 0 5 5 1 . 0 0 . 2 300-1500 787 2.6 0.52 24.92 3.00 9.1 0.12 Part 15 1500-100000 5555 5.0 1.0 28.2 14.0 50.4 3.30 Part 27 N O T E : E n t e r P ( m W ) Equivalent dBm E E n t e r d B m Equivalent Watts A n t e n n a s N o t C o - l o c a t e d B a s i s o f C a l c u l a t i o n s : 8 9 5 . 4 2 9 . 5 2 2 9 . 5 2 895.4 E^2/3770 = S, mW/cm2E, V/m = (Pwatts*Ggain*30)^.5/d, metersd = ((Pwatts*G*30)/3770*S))^0.5 Pwatts*Ggain = 10^(PdBm-30+GdBi)/10) S@20cm = 20 log (MPE dist/20cm) N O T E : F o r m o b i l e o r fi x e d l o c a t i o n t r a n s m i t t e r s , m i n i m u m s e p a r a t i o n d i s t a n c e i s f o r F C C c o m p l i a n c e i s 2 0 c m , e e v e n i f c a l c u l a t i o n s i n d i c a t e M P E d i s t a n c e i s l e s s Page 1

Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamina 30500, Israel Tel. +972-4-6288001 Fax. +972-4-6288277 E-mail: [email protected] Page 1 of 69 Report ID: ARCRAD_FCC.20571_p27.doc Date of Issue: 3/18/2010 Electrical 839.01 TEST REPORT ACCORDING TO: FCC 47CFR part 27 FOR: Arcadian Networks Inc. Wireless Modem Model:AE11GOW This report is in conformity with ISO/ IEC 17025. The "A2LA Accredited" symbol endorsement applies only to the tests and calibrations that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: ARCRAD_FCC.20571_p27.doc Date of Issue: 3/18/2010 Page 2 of 69 Table of contents 1 Applicant information..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details.................................................................................................................................................................... 3 5 Tests summary.............................................................................................................................................................. 4 6 EUT description............................................................................................................................................................. 5 6.1 General information....................................................................................................................................................... 5 6.2 Ports and lines .............................................................................................................................................................. 5 6.3 Support and test equipment .......................................................................................................................................... 5 6.4 Operating frequencies ................................................................................................................................................... 5 6.5 Changes made in the EUT ............................................................................................................................................ 5 6.6 Test configuration.......................................................................................................................................................... 6 6.7 Transmitter characteristics ............................................................................................................................................ 7 7 Transmitter tests according to 47CFR part 27............................................................................................................... 8 7.1 Peak output power test.................................................................................................................................................. 8 7.2 Occupied bandwidth test ............................................................................................................................................. 10 7.3 Band edge emissions at RF antenna connector test ................................................................................................... 14 7.4 Radiated spurious emission measurements................................................................................................................ 24 7.5 Radiated spurious emission measurements in 1559-1610 MHz band ........................................................................ 30 7.6 Spurious emissions at RF antenna connector test in 763 – 775 MHz and 793 – 805 MHz ........................................ 37 7.7 Spurious emissions at RF antenna connector test ...................................................................................................... 41 7.8 Frequency stability test................................................................................................................................................ 50 7.9 RF exposure................................................................................................................................................................ 57 8 APPENDIX A Test equipment and ancillaries used for tests....................................................................................... 58 9 APPENDIX B Measurement uncertainties................................................................................................................... 59 10 APPENDIX C Test laboratory description ................................................................................................................... 60 11 APPENDIX D Specification references ....................................................................................................................... 60 12 APPENDIX E Test equipment correction factors......................................................................................................... 61 13 APPENDIX F Abbreviations and acronyms................................................................................................................. 69 Report ID: ARCRAD_FCC.20571_p27.doc Date of Issue: 3/18/2010 Page 3 of 69 1 Applicant information Client name: Arcadian Networks Inc Address: 400 Columbus Avenue, Suite 210E, Valhalla NY 10595, USA Telephone: +972 3976 9847 Fax: +972 3976 9998 E-mail: [email protected] Contact name: Mr. Hillel Hendler 2 Equipment under test attributes Product nam…

Text truncated - open the document above for the full version.

Arcadian Networks Inc. FCC ID:V72AE11 Page 1 of 7 SETUP PHOTOGRAPHS This document contains 6 photographs Arcadian Networks Inc. FCC ID:V72AE11 Page 2 of 7 Photograph No.1 Peak output power, occupied bandwidth and spurious emissions measurements at RF antenna connector test setup Arcadian Networks Inc. FCC ID:V72AE11 Page 3 of 7 Photograph No.2 Setup for spurious emission field strength measurements in 9 kHz to 30 MHz range in the anechoic chamber Arcadian Networks Inc. FCC ID:V72AE11 Page 4 of 7 Photograph No.3 Setup for spurious emission field strength measurements above 1 GHz range in the anechoic chamber Arcadian Networks Inc. FCC ID:V72AE11 Page 5 of 7 Photograph No.4 Setup for spurious emission field strength measurements in 1559-1610 MHz band Arcadian Networks Inc. FCC ID:V72AE11 Page 6 of 7 Photograph No.5 Setup for substitution method measurements in the anechoic chamber Arcadian Networks Inc. FCC ID:V72AE11 Page 7 of 7 Photograph No.6 Setup for frequency stability measurements