VA5CMT348-X2MAXMODEM

User Manual By Firstech LLC, Version: 1.1 Model NameFCC IDICContains FCC IDContains IC DR-X2MAXVA5CMT348-X2MAX 7087A-CMT348X2M XMR2020BG95M1 10224A-2020BG95M1 It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner. (1) When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in “Park” in order to avoid accidents upon device starting. (Note: Make sure that the automatic vehicle cannot star in “Drive”.) (2) It is the user’s responsibility to ensure that the device is disabled or put into valet mode before servicing. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions su ivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. WARNING FCC COMPLIANCE IC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device should be installed and operated with minimum 20 cm between the radiator and your body. a. Part 15.105 b. Part 15.21 c. RF exposure User Registration 1. To create a DroneMobile Account, please begin by downloading the free DroneMobile App from the App Store or Google Play. Open the DroneMobile App and press "Register". 2. Enter the DR-X2 MAX serial number printed on the Keychain Tag. You can do this quickly by pressing "Scan" in the DroneMobile App, or by manually inputting the serial number. • If you did not receive a keychain tag from your dealer/installer, please contact them immediately to retrieve this information. You will be unable to create an account without your serial number. 3. Once you have entered your serial number, please input a valid email address. This will be your DroneMobile username. 4. To confirm your email address, please check your inbox for a confirmation email. Once you have received the email, please click the link to complete the registration process. • If you do not receive the confirmation email, refresh your email or check your junk/spam folder. 5. Reopen your DroneMobile App to begin your connected car journey! Online Support : https://support.dronemobile.com Toll-Free Support : 1(888)820-3690 Facebook : @dronemobile BASICS OF USING DRONEMOBILE 1. How to register your new DroneMobile system from the app ① Upload Profile Picture ② Upload vehicle image ③ Add vehicle detail ④ Enable location services ⑤ Enable push notifications 2. The DroneMobile Home Screen and the information that it shows - Location - Drivers - Battery - Status - Temperature - Driving - System BASICS OF USING DRONEMOBILE 3. Remote starting and controlling your vehicle from the DroneMobile App - Start / Stop - Lock / Unlock - Aux 1 - Aux 2 - Trunk - Panic 4. Viewing your vehicle's activity on the Activity Page - Activity (Alerts & Feed) - Vehicle Info - Setup 5. Adjusting settings for your DroneMobile System 6. Setting your App Preferences for the DroneMobile App Dealer Activation & Installation 1. Confirm your DR-X2 MAX is connected to power by verifying that the on-board LEDs are lighting up. DR-X2 MAX modules can be connected to power via the following: • A direct connection to a compatible aftermarket remote start or security system using the included data harness. 2. Go to myFirstech Install at https://install.myfirstech.com using your desktop, tablet, or smartphone's web browser. Note: Internet Explorer is not supported. 3. Login to your DroneMobile Dealer Account and enter the DR-X2 MAX device's serial number. It is the top barcode on the module sticker. • You cannot use your personal DroneMobile User Account to activate a DR-X2 MAX. • If you do not have a dealer login, you can "Activate as Guest". You will also be required to also enter the DR-X2 MAX device's ICC ID. 4. Activate, test, and configure y…

Text truncated - open the document above for the full version.

CFR 47 §2.911 (d)(5) Attestation Date: 03-07-2023 FCC ID: VA5CMT348-X2MAX To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1. SEGI LIMITED (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. SEGI LIMITED (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Young il Chang Job Title: President Company Name: SEGI LIMITED

CFR 47 §2.911 (d)(7) FCC US Agent Letter of Attestation Date: 03-07-2023 FCC ID: VA5CMT348-X2MAX To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA FCC US Agent Agent Company Name : Firstech, LLC FRN: 0033475344 Agent Contact Name : Namwoo Kim Agent US Address : 21903 68th Ave. South Kent, WA 98032 US Agent Email Address : [email protected] This letter is to confirm that we have accepted the responsibility to act as US Agent on behalf of SEGI LIMITED(“the applicant”) for the above referenced FCC ID. We are aware of the requirements and responsibilities of the applicant’s agent for service of process as outlined in the FCC section 2.911(d)(7) and Report and Order FCC 22-84 paragraph 63. Sincerely yours, Authorized Agent Contact Person Name : Namwoo Kim Agent contact Job Title : Engineering Director Agent Company name : Firstech, LLC

CFR 47 §2.911 (d)(7) Agent Designation Attestation Date: 03-07-2023 FCC ID: VA5CMT348-X2MAX To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA SEGI LIMITED (“the applicant”) as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicant’s agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. U. S. Agent Information: Contact Person : Namwoo Kim Company Name : Firstech, LLC Company Address : 21903 68th Ave. South Kent, WA 98032 US Email : [email protected] Sincerely yours, Name: Young il Chang Job Title: President Company Name: SEGI LIMITED

SEGI LIMITED Date: 7th of March, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Inc . (formerly UL CCS) Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it ma y concern: I, th e undersigned, hereby authorize UL-Korea an d hereafter referred to as ULK, to ac t on our behalf in al l manners relating to application fo r equipment authorization, including signing of all documents relating to these matters. An y an d al l act s carried ou t by UL-Korea on ou r behalf shall have th e same effect as act s of ou r own. I, th e undersigned, hereby certify tha t we ar e no t subject to a denial of federal benefits, tha t includes FC C benefits, pursuant to Section 5301 of the Anti-Drug Abuse Ac t of 1988, 21 U.S.C. 853(a). In authorizing UL K as ou r agent, we stil l recognize tha t we ar e responsible to: a)comply with the relevant provisions of the certification program; b)make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)make claims regarding certification only in respect of the scope for which certification has been granted; d)do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f)use certification only to indicate the products are certified as being in conformity with specified standards; g)endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h)ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i)keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j)take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k)document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By Young il Chang President SEGI LIMITED REMARK: 1.This authorization letter will be sent along with your application when filing with the Certification Division. 2.Please follow the format and type it on company letterhead and send original to us. 3.Authorized signature must be in agreement with grantee code contact in FCC database.

SEGI LIMITED Workshop J2, 4th floor of Block 1, Kinho Industrial Buildings Nos 14-24 Au Pui Wan street, Shatin, N.T, Hongkong Date: March 7, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: Request of Confidentiality for FCC ID: VA5CMT348-X2MAX To Who m It ma y Concern: Pursuant to Sections 0.45 7 an d 0.45 9 of th e Commission`s Rules(CFR 47) , an d Sectio n 55 2 (b ) (4 ) of th e Freedom of Information Act, SEG I LIMITED. Her e by requests confidentiality an d treatment of certai n information accompanying thi s application. The materials contai n trad e secret s an d proprietary information no t customarily released to th e public. Th e publi c disclosure of thes e matter s migh t be harmful to th e Applicant an d provid e unjustified benefits to it s competitors. We ar e als o hereb y request Short-Term Confidentiality fo r 180 day s afte r th e gran t as outlined in Publi c Notic e DA 04-1705. This provision wil l giv e SEG I LIMITED. temporary confidentiality of commercially sensitive information prio r to product release. Th e requested permanent an d Short-Term Confidential exhibit s ar e liste d as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Schematics 3 Part Lists 4 Operation Description SHORT-TERM 5 Internal photo 6 User Manual 7 NA 8 NA The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Young il Chang President

FCC ID : Page : 1 of 3 IC : VA5CMT348-X2MAX 7087A-CMT348X2M UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 EXTERNAL PHOTOS OF EUT Top view of EUT Bottom view of EUT FCC ID : Page : 2 of 3 IC : VA5CMT348-X2MAX 7087A-CMT348X2M UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Front view of EUT Rear view of E UT FCC ID : Page : 3 of 3 IC : VA5CMT348-X2MAX 7087A-CMT348X2M UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Right side of EUT Left side of EUT

Label and Location DR-X2MAX * This label is attached to the back of the product and not easily removed. Size Label 39.8 x 44.8mm

FCC ID : Page : 1 of 3 IC : VA5CMT348-X2MAX 7087A-CMT348X2M UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 INTERNEL PHOTOS OF EUT Ope n EUT FCC ID : Page : 2 of 3 IC : VA5CMT348-X2MAX 7087A-CMT348X2M UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Main board top view FCC ID : Page : 3 of 3 IC : VA5CMT348-X2MAX 7087A-CMT348X2M UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Main board bottom side Antenna

FCC ID: RF function or Mode Max Target Power (dBm) ANT Gain (dBi) Maximum EIRP (dBm) Maximum EIRP (mW) Requriment Power Threshold (mW) BLE2402.00~2480.001.001.692.691.8583060.000 ~ ~ ~ ~ ~ ~ ~ Conclusion : The exposure condition of this device is compliant with FCC KDB 447498 D04 Interim General RF Exposure Guidance v01. Appendix B B.3 MPE-based Exemption B.4 SAR-based Exemption VA5CMT348-X2MAX MPE Calculation :Bluetooth LE Frequency range (MHz) The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the user. The MPE sample calculation for this exposure is shown below. Note1: Please refer to the operation description for Max tune-up power. Note2: EIRP is worst case as it's greater than ERP FCC ID: RF function or Mode Max Target Power (dBm) ANT Gain (dBi) Maximum EIRP (dBm) Maximum EIRP (mW) Requriment Power Threshold (mW) LTE(Band 2)1850.00~1910.0022.701.1823.88244.3443060.000 LTE(Band 4)1710.00~1755.0022.700.6923.39218.2733060.000 LTE(Band 12)699.00~716.0022.70-0.8321.87153.8161425.960 LTE(Band 13)777.00~787.0022.70-2.3420.36108.6431585.080 ~ ~ ~ ~ Conclusion : The exposure condition of this device is compliant with FCC KDB 447498 D04 Interim General RF Exposure Guidance v01. Appendix B B.3 MPE-based Exemption B.4 SAR-based Exemption VA5CMT348-X2MAX MPE Calculation :LTE Frequency range (MHz) The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the user. The MPE sample calculation for this exposure is shown below. Note1: The tolerance has been considered Note2: EIRP is worst case as it's greater than ERP ▪ ▪ KDB 447498 D04 Interim General RF Exposure Guidance v01. Appendix B B.3 MPE-based Exemption B.4 SAR-based Exemption 0.0685 0.0719 0.0691 0.1085 Configuration 3 (MPE ratio) 0.00060.1079 LTERF function or mode 0.1079 153.8160108.64301.8580 3060.0000 0.0006 244.3440 Maximum EIRP (mW) 218.2730 -LTELTE Band 13 BLE+LTE Configuration 2 (MPE ratio) 0.00060.0713 0.0006 Band 2 3060.00001585.0800 0.0805 3060.0000 Σ of MPE ratios - - - The exposure condition of this device is compliant with FCC rules. Conclusion : Σ of MPE ratios ≤ 1▪ Requirment = 0.06850.0713 Configuration 4 (MPE ratio) 0.0006 Requriment Power Threshold (mW) Note1: The maximum power density in each RF function was used for above table. Note2: EIRP is worst case as it's greater than ERP Configuration 1 (MPE ratio) -0.0799 MPE ratio (Power Density/Requirement) 0.0799 VA5CMT348-X2MAX FCC ID: RF Exposure Compliance for simultaneous operations 1425.9600 Worst case for simultaneous operations Band 12Band 4Band(Worst case) BLELTE 2.4GHz

CERTIFICATION TEST REPORT Report Number. : 4790736850-E3V4 Applicant : SEGI LIMITED Unit J2, 4/F, Block 1, Kinho Industrial Building,14-24 Au Pui Wan Street, Shatin, New Territories HONGKONG, China Model : DR-X2MAX FCC ID : VA5CMT348-X2MAX IC : 7087A-CMT348X2M EUT Description : MODEM Test Standard(s) : FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-Gen Issue 5 INDUSTRY CANADA RSS-247 Issue 2 Date Of Issue: 2023-04-13 Prepared by: UL Korea, Ltd. 26th floor, 152, Teheran-ro, Gangnam-gu Seoul, 06236, Korea Suwon Test Site: UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 REPORT NO: 4790736850-E3V4 DATE: 2023-04-13 FCC ID: VA5CMT348-X2MAX IC: 7087A-CMT348X2M Page 2 of 34 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(04) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. Rev. Issue Date Revisions Revised By V1 2023-03-06 Initial issue Sungeun Lee V2 2023-04-07 Updated to address TCB’s question Sungeun Lee V3 2023-04-11 Updated to address TCB’s question Sungeun Lee V4 2023-04-13 Updated to address TCB’s question Sungeun Lee REPORT NO: 4790736850-E3V4 DATE: 2023-04-13 FCC ID: VA5CMT348-X2MAX IC: 7087A-CMT348X2M Page 3 of 34 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(04) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST METHODOLOGY ..................................................................................................... 6 3. FACILITIES AND ACCREDITATION ................................................................................. 6 4. DECISION RULES AND MEASUREMENT UNCERTAINTY .............................................. 7 4.1. METROLOGICAL TRACEABILITY ................................................................................ 7 4.2. SAMPLE CALCULATION .............................................................................................. 7 4.3. MEASUREMENT UNCERTAINTY ................................................................................ 7 4.4. DECISION RULES ........................................................................................................ 7 5. EQUIPMENT UNDER TEST ............................................................................................... 8 5.1. EUT DESCRIPTION...................................................................................................... 8 5.2. MAXIMUM OUTPUT POWER ....................................................................................... 8 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................... 8 5.4. WORST-CASE CONFIGURATION AND MODE ........................................................... 8 5.5. DESCRIPTION OF TEST SETUP ................................................................................. 9 6. MEASUREMENT METHOD...............................................................................................11 7. TEST AND MEASUREMENT EQUIPMENT ......................................................................12 8. TEST RESULTS SUMMARY .............................................................................................13 9. ANTENNA PORT TEST RESULTS ...................................................................................14 9.1. ON TIME AND DUTY CYCLE ......................................................................................14 9.2. 6 dB & 99% BANDWIDTH ............................................................................................15 9.2.1. Test data................................................................................................................15 9.2.2. 6 dB & 99% BANDWIDTH PLOTS .........................................................................16 9.3. OUTPUT POWER ........................................................................................................17 9.3.1. Test data................................................................................................................17 9.3.2. PEAK POWER PLOTS ..........................................................................................18 9.4. AVERAGE POWER .....................................................................................................19 9.4.1. Test data................................................................................................................19 9.5. POWER SPECTRAL DENSITY ...................................................................................20 9.5.1. Test data................................................................................................................20 9.5.2. PSD TEST PLOTS ................................................................................................21 9.6. CONDUCTED SPURIOUS EMISSIONS ......................................................................22 9.6.1. Test plot .................................................................................................................23 REPORT NO: 4790736850-E3V4 DATE: 2023-04-13 FCC ID: VA5CMT348-X2MAX IC: 7087A-CMT348X2M Page 4 of 34 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(04) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 10. RADIATED TEST RESULTS ..........................................…

Text truncated - open the document above for the full version.

1. DR-X2MAX BLE Antenna Test & System Description A. Test Setup B. Equipment list Device Type Manufacturer SW Calibration Data Anechoic Chamber - MTG - 2022-10-01 Horn Antenna - HA-07M18G-NF - - Network Analyzer N230A AGILENT - 2022-02-11- Measurement SW - - VWM21 - Positioner Controller PC-510-4 MTG - - Measurement Measurement Date Measuring person Galtronics 2022-12-07 Park Jin Wan 2. BLE Setup photo 3. BLE Antenna Pattern & Gain Report

1. DR-X2MAX LTE Antenna Test & System Description A. Test Setup B. Equipment list Device Type Manufacturer SW Calibration Data Anechoic Chamber - MTG - 2022-10-01 Horn Antenna - HA-07M18G-NF - - Network Analyzer N230A AGILENT - 2022-02-11- Measurement SW - - VWM21 - Positioner Controller PC-510-4 MTG - - Measurement Measurement Date Measuring person Galtronics 2022-12-07 Park Jin Wan 2. LTE Setup photo 3. LTE Antenna Pattern & Gain Report

1. Appendix: UNLICENSED BAND SETUP PHOTOS(Conducted Test) 1) CONDUCTED RF MEASUREMENT SETUP (BLE) CONDUCTED TEST PHOTO Page 2 of 5 2. Appendix: UNLICENSED BAND SETUP PHOTOS(Radiated Test) 1) RADIATED RF MEASUREMENT SETUP (BELOW 1 GHz) BELOW 1 GHz FRONT TEST PHOTO BELOW 1 GHz REAR TEST PHOTO Page 3 of 5 2) RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz) ABOVE 1 GHz FRONT TEST PHOTO ABOVE 1 GHz REAR TEST PHOTO Page 4 of 5 3) RADIATED RF MEASUREMENT SET-UP (Axis) X AXIS PHOTO Y AXIS PHOTO Page 5 of 5 END OF TEST PHOTO Z AXIS PHOTO