VDDATICO01315 MHz Wireless Device

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 IMPORTANT INFORMATION REQUIRED BY THE FCC THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. !! CAUTION-- To reduce the risk of personal injury or product/property damage: • Do not immerse the product in water or other liquid. Battery Handling and Usage WARNING: Keep batteries away from children and pets. • Do not mix a used battery with a new battery, or mix different chemistries or sizes of batteries. • Insert the batteries observing the proper polarity (+/−) as indicated inside the Battery Compartment. CAUTION: Failure to properly align the battery polarity can cause personal injury and/or property damage. • Never throw batteries into a fire. Do not expose batteries to fire or other heat sources. Installing Batteries of Light: Slide the Power Switch to OFF. Open the Battery Compartment and place four “AAA” size alkaline batteries (not included) into the Battery Compartment according to the polarity indications. Close the Battery Compartment. Replacing Light Switch Battery: 1. Remove the front of the Light Switch as described below. 2. Remove the spent battery and place a new A23, 12-volt, alkaline battery into the Battery Compartment, correctly observing the polarity indications. 3. Replace the front of the Light Switch with the Screws. To Set Up • The Light may be operated without the Light Switch (see “To Use” section). • Both the Light and Light Switch have a key hole for one mounting option. If desired, place the keyhole onto a screw or nail that will safely support the item. APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 1. Activate Light Switch battery: a. Remove the Screw Covers from the Light Switch by turning them counterclockwise with a flathead screwdriver. Then, use a Phillips screwdriver to remove the Screws (see figure). b. Lift the front of the Light Switch off the back. Pull the plastic tab out of the Battery Compartment and replace the front. 2. Place the Light and the Light Switch in the desired locations. Slide the Power Switch to (ON – Light Switch Operation). NOTE: Maximum range for the Light Switch is 98 ft (30 m) and large metal objects may interfere with the signal. 3. Press one end of the Light Switch to illuminate the Light and the other end to shut off the Light. If the Light does not respond, reposition the Light, the Light Switch, or both. Mount Light and Light Switch Using Adhesives: 1. Stick two Mounting Adhesives onto the back of the Light and the Light Switch. 2. Firmly press the Light and Light Switch against the clean, desired mounting surfaces. Mount Light Switch Using Screws and Anchors: 1. Remove the front of the Light Switch. Place the back of the Light Switch against the mounting surface. Mark the screw holes (two smallest holes in the back). 2. Drill two ¼-inch holes where marked and insert Anchors into the holes. 3. Align the screw holes with the Anchors and secure with two Screws. 4. Replace the front of the Light Switch. To Use 1. Slide the Power Switch to (ON) or (ON – Light Switch Operation). 2. If operating with the Light Switch, press one end of the Switch to illuminate the Light and the other end to shut off the Light. 3. To turn off the Light, slide the Power Switch to OFF. Turn off the Light when not using it for an extended period. Item #A14C0606 WIC #559044 ©2007 All Rights Reserved Distributed By: East West Distributing Co. Deerfield, IL 60015-4616 Made in China APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 315MHz DC Main High frequency surge (32.768 kHz Crystal) Low frequency surge

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Label Drawing FCC ID: VDDATICO01 Model Number: A14C0606(559044) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Label Location

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Circuit Description of transmitter Description of circuit: The brief circuit description is listed as follow: 1. Low frequency oscillating circuit : IC1AIC1BR532768R4 2. Modulation circuit: IC1CR3 3. High frequency oscillating circuit : Q1C2L2, R1C1 4. Attenuator: R2(The attenuator limits the radiated electric field level from the transmitter to the level allowed by regulations (such as FCC and CE). 5. The touch button switch: After push the switch to turn the light on, when take off the switch, the transmission will cease immediately after took off the switch.

MOST TECHNOLOGY SERVICE CO., LTD. Tel:(86) 755-86170306 Fax:(86) 755-86170310 Http:// www. szmost.com Email: [email protected] APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Cover Sheet Test Report Product Name: Ultrasonic Remote Control LED Flashlight FCC ID: VDDATICO01 MODEL NO. : A14C0606(559044) Applicant: ATICO INTERNATIONAL (ASIA) LTD. G/F-2F Hunghom Bay Centre, 22-24 Hunghom Wan Street, Hunghom, Kowloon, Hong Kong Date Received: 6/06/2007 Date Tested: 6/06/2007 MOST TECHNOLOGY SERVICE CO., LTD. Tel:(86) 755-86170306 Fax:(86) 755-86170310 Http:// www. szmost.com Email: [email protected] APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 TABLE OF CONTENTS TABLE OF CONTENTS APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 TEST REPORT CONTAINING: PAGE 1...........TEST EQUIPMENT LIST PAGE 2...........TEST PROCEDURE PAGE 3...........RADIATION INTERFERENCE TEST DATA PAGE 4-5.........OCCUPIED BANDWIDTH AND PLOTS PAGE 6-7.........DUTY CYCLE PLOTS EXHIBIT INCLUDED: PAGE 1...........BLOCK DIAGRAM PAGE 2...........SCHEMATIC PAGE 3...........USERS MANUAL PAGE 4...........LABEL SAMPLE PAGE 5...........LABEL LOCATION PAGE 6...........EXTERNAL PHOTOGRAPHS PAGE 7...........INTERNAL PHOTOGRAPHS PAGE 8...........OPERATIONAL DESCRIPTION PAGE 9...........TEST SET UP PHOTOGRAPHS MOST TECHNOLOGY SERVICE CO., LTD. Tel:(86) 755-86170306 Fax:(86) 755-86170310 Http:// www. szmost.com Email: [email protected] APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Page 1 of 7 EMC Equipment List Remark: Test Firm Name: Most Technology Service Co., Ltd. Test Firm Address: No. 5, 2nd Langshan Road, North District, Hi-tech Industrial Park,Nanshan, Shenzhen, Guangdong, China FCC Registered Test Site Number: 490827 Equipment Manufacturer Model No.Serial No.Last Cal. Cal. Interval EMI Test Receiver ROHDE&SCHWARZ ESCI 100492 Apr 06,2007 1 Year LISN ROHDE&SCHWARZ ENV216 100093 Apr 06,2007 1Year EMI Test Receiver ROHDE&SCHWARZ ESCI 101202 Apr 06,2007 1 Year 50 Coaxial Switch ANRITSU CORP MP59B 6200283933 Apr 06,2007 1 Year Bilog Antenna Sunol JB3 A121206 Apr 06,2007 1 Year 50 Coaxial Switch ANRITSU CORP MP59B 6200283933 Apr 06,2007 1 Year Cable Resenberger N/A NO.1 Apr 06,2007 1 Year Cable SCHWARZBECK N/A NO.2 Apr 06,2007 1 Year Cable SCHWARZBECK N/A NO.3 Apr 06,2007 1 Year Single Phase Power Line Filter Kikusui LIN40MA-PC R-L LM002352 Apr 06,2007 1Year AC Power Source Kikusui AC40MA LM003232 Apr 06,2007 1Year Test analyzer Kikusui KHA1000 LM003720 Apr 06,2007 1Year ESD Tester Kikusui KES4021 LM003537 Apr 08,2007 1 Year Signal Generator IFR 2032 203002/100 Apr 08,2007 1 Year Amplifier A&R 150W1000 301584 NCR NCR Dual Directional Coupler A&R DC6080 301508 Apr 06,2007 1 Year Power Head A&R PH2000 301193 Apr 06,2007 1 Year Power Meter A&R PM2002 302799 Apr 06,2007 1 Year Field Monitor A&R FM5004 300329 Apr 06,2007 1 Year Field Probe A&R FP5000 300221 Apr 06,2007 1 Year EMCPRO System EM Test UCS-500-M4 V064810202 6 Apr 06,2007 1 Year EMCPRO System EM Test UCS-500-M4 V064810202 6 Apr 06,2007 1 Year MOST TECHNOLOGY SERVICE CO., LTD. Tel:(86) 755-86170306 Fax:(86) 755-86170310 Http:// www. szmost.com Email: [email protected] APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Page 2 of 7 TEST PROCEDURE GENERAL: This report shall NOT be reproduced except in full without the written approval of SHENZHEN MOST ELECTRONICS CO., LTD. The EUT was transmitting a test signal during the testing. POWER LINE CONDUCTED INTERFERENCE: The test procedure used was ANSI Standard C63.4-2003 using a 50H LISN. Both Lines were observed. The bandwidth of the receiver was 10kHz with an appropriate sweep speed. The ambient temperature of the EUT was 25 with a humidity of 58%. RADIATION INTERFERENCE: The test procedure used was ANSI Standard C63.4-2003 using a ANRITSU spectrum analyzer with a pre-selector. The analyzer was calibrated in dB above a micro volt at the output of the antenna. The resolution bandwidth was 100 kHz and the video bandwidth was 300 kHz up to 1 GHz and 1 MHz with a video BW of 3 MHz above 1 GHz. The ambient temperature of the EUT was 25 with a humidity of 58%. FORMULA OF CONVERSION FACTORS: The Field Strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer. The antenna correction factors are stated in terms of dB. The gain of the Pre-selector was accounted for in the Spectrum Analyzer Meter Reading. Example: Freq (MHz) METER READING + ACF = FS 33 20 dBuV + 10.36 dB = 30.36 dBuV/m @ 3m ANSI STANDARD C63.4-2003 10.1.7 MEASUREMENT PROCEDURES: The EUT was placed on a table 80 cm high and with dimensions of 1m by 1.5m. The EUT was placed in the center of the table (1.5m side). The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and vertical planes. The situation was similar for the conducted measurement except that the table did not rotate. The EUT was setup as described in ANSI Standard C63.4-2003 10.1.7 with the EUT 40 cm from the vertical ground wall. MOST TECHNOLOGY SERVICE CO., LTD. Tel:(86) 755-86170306 Fax:(86) 755-86170310 Http:// www. szmost.com Email: [email protected] APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 Page 3 of 7 APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01 NAME OF TEST: RADIATION INTERFERENCE RULES PART NUMBER: 15.231 REQUIREMENTS: Fundamental Frequency MHz Field Strength of Fundamental dBuV Field Strength of Harmonics and Spurious Emissions (dBuV/m @ 3m) 40.66 to 40.70 67.04 47.04 70 to 130 61.94 41.94 130 to 174 61.94 to 71.48 41.94 to 51.48 174 to 260 71.48 51.48 260 to 470 71.48 to 81.94 51.48 to 61.94 470 and above 81.94 61.94 THE LIMIT FOR AVERAGE FIELD STRENGTH…

Text truncated - open the document above for the full version.

APPLICANT: ATICO INTERNATIONAL (ASIA) LTD. FCC ID: VDDATICO01