VHNAC6060Remote Control

User Manual Remote Control AC6060 General ： ：： ： The remote is wholly used for matching AC 120V motor use, using 12V battery-powered, simple operation, stable performance, reliable quality. type： ：： ： remote type：AC6060。 Main function： ：： ： Used for matching AC 120V motor use, through 5 keys on the remote, it is easy to operate after opening the back of the battery cover to install battery. Structure chart ： ：： ： See attached fig1： 1、high speed grade start key； 2、medium speed grade start key； 3、low speed grade start key； 4、halt key； 5、light control key； 6、LED light； 7、12V battery； Specification: 1, working voltage: DC-12V 2, static current: less than 8 uA 3, working current: less than 20 mA; 4, effective assorting space with the receiver in the same series: not less than 15 meters; instruction 1. key “1” is for start from high speed grade, which is pressed to start the motor from high speed grade. If the motor is working at other speed grade, key 1 pressed will make the motor adjustable to high speed grade. 2. key “2” is for start from medium speed grade, which is pressed to start the motor from medium speed grade. If the motor is working at other speed grade, key 2 pressed will make the motor adjustable to medium speed grade. 3. key “3” is for start from low speed, which is pressed to start the motor from low speed grade. If the motor is working at other speed grade, key 3 pressed will make the motor adjustable to low speed grade. 4. key "4" is to halt, which is pressed to stop the motor from work. 5.key “5”is to control lights. Short pressure and long pressure can control switch and can adjust the brightness respectively. The user can loosen the key when the brightness meets user’s need. The lights change as follows: current brightness
brightest
darkest
brightest 6, In case of key pressed, the LED lights shine. LED lights will be turned off in case of the key loosened. 7, Install battery here. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Attached fig1.

Report No.: SZEMO071103152RFF Page: 1 of 13 FCC ID: VHNAC6060 Authorized Signature: Robinson Lo Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.” Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This document cannot be reproduced except in full, without prior approval of the Company. SGS-CSTC Standards Technical Services Ltd. No.198 Kezhu Road, Science Town Economic& Technology Development District Guangzhou, China 510663Telephone: Telephone: +86 (0) 20 82155555 Fax: +86 (0) 20 82075059 Email: [email protected] FEDERAL COMMUNICATIONS COMMISSION Registration number: 282399 TEST REPORT Application No. : SZEMO071103152RF Applicant : Youngo Limited Manufacturer : SHENZHEN POWERWONDER ELECTRONICS CO., LTD FCC ID : VHNAC6060 Fundamental Frequency : 303.96MHz Equipment under Test (EUT): Name : Remote Control Model : AC6060 Standards : FCC PART 15, SUBPART C : 2007 (Section 15.231) Date of Receipt : 07 November 2007 Date of Test : 26 November to 19 December 2007 Date of Issue : 07 January 2008 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. FCC ID:VHNAC6060 This document is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.” Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This document cannot be reproduced except in full, without prior approval of the Company Report No.: SZEMO071103152RFF Page: 2 of 13 SGS-CSTC Standards Technical Services Ltd. 2 Test Summary Test Test Requirement Stanadard Paragraph Result Radiated Emission (30MHz to 1000MHz) FCC PART 15 : 2007 Section 15.231 PASS Occupied Bandwidth FCC PART 15 : 2007 Section 15.231 PASS Dwell Time FCC PART 15 : 2007 Section 15.231 PASS FCC ID:VHNAC6060 This document is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.” Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This document cannot be reproduced except in full, without prior approval of the Company Report No.: SZEMO071103152RFF Page: 3 of 13 SGS-CSTC Standards Technical Services Ltd. 3 Contents Page 1 COVER PAGE .................................................................................................................................... 1 2 TEST SUMMARY..........................................................................................................................................2 3 CONTENTS...................................................................................................................................................3 4 GENERAL INFORMATION.......................................................................................................................…

Text truncated - open the document above for the full version.