VIXSPKAW740M2Center Stage Freestyle All-in-One Karaoke System

QUICK START GUIDE Instructions en français .....................................10 Instrucciones en español ....................................19 CENTER STAGEFREESTYLE A L L - I N- O NE KA RA O K E SY S TEM For Video Setup Instructions, Scan Here! FPO 2 Step 1: Unpack Make sure the following items came in this package: Center Stage base Microphone stand Device cradle and locking knob AC power adapter 2 Wireless Microphones Step 2: Remove the remote battery tab Pull the battery tab out of the bottom of the remote. The battery will start powering the remote so you can use it. Remote control with pre-installed battery 3 Step 3: Put it together Insert the microphone stand into the center of the Center Stage base as shown here. Screw the microphone stand clockwise into the base until it’s fastened tight. Adjust the height of the stand by turning each clutch counterclockwise and lifting the pole to the desired length. Make sure to tighten each clutch (turn clockwise) before you proceed. Party system base Microphone stand Clutches Microphone stand Attach the device cradle to the stand using the locking knob. Place the cradle on the top of the stand. Then insert the locking knob in the hole on the back of the device cradle and tighten it until the cradle feels secure. Do not overtighten! Microphone stand Locking knob Device cradle, side IMPORTANT: Make sure the microphone stand is tightened as much as it can be before proceeding. 4 Press and hold the button on the top of the Center Stage base (or on the remote) to turn it on. The Center Stage plays its startup sound and the indicator below the button starts blinking slowly. After 15–30 seconds, the Center Stage announces “Pairing” and goes to Bluetooth pairing mode to set up with your Bluetooth device. The indicator below the button starts blinking faster. Step 4: Plug in Step 5: Turn on Attach one end of the AC adapter to the DC jack on the left side of the Center Stage base. Plug the other end of the adapter into a working outlet or surge protector. Base 5 Enable Bluetooth on your smartphone or other Bluetooth device. Step 6: Pair + Connect Wi-Fi Bluetooth Bluetooth Settings VPN Settings Wi-Fi Settings 8:45PM Make sure the indicator below the button on the top of the Center Stage is blinking rapidly. (If it isn’t, give a short double-press on the button. The Center Stage announces “Pairing.”) If you’ve previously paired your phone or other Bluetooth device with the Center Stage, it will automatically attempt to reconnect to that device when you switch it on. If you want to pair to a new device, give a short double-press to the button. The Center Stage announces “Pairing” and the indicator below the button starts blinking. Choose SINGSATION CENTER STAGE from the pairing options on your Bluetooth device. (If it’s not in the list, choose “Scan” from your device’s Bluetooth menu.) The Center Stage announces “Device Connected” when it’s finished pairing and connecting to your Bluetooth device. The indicator below the button turns solid blue. Note: The process of enabling Bluetooth and connecting varies from device to device. See your device’s owners manual for more information and specific instructions. Bluetooth Wireless Connection Tips • Make sure the Bluetooth capability of your device is turned on. • Make sure there’s nothing plugged into the Center Stage’s (line in) jack when you’re trying to use Bluetooth. • The Bluetooth wireless connection works up to a range of roughly 33 feet (10 meters). This range may vary, however, based on other factors, such as room layout, wall material, obstacles, your device’s Bluetooth performance, etc. If you’re having problems connecting to the speaker, move closer to it. • If your device asks you for a password to connect, use “0000”. Base 6 Step 8: Sing along! Center Stage, Front Step 7: Install wireless mic batteries The Center Stage comes with 2 wireless microphones you can use to sing along or make announcements! Each microphone requires 2 AA batteries (not included). To install batteries in each microphone: Open the battery door on the back of the microphone by sliding it down. Insert 2 AA batteries in the battery compartment (make sure you follow the + and – diagrams in the compartment). Then slide the battery door back up until it clicks back into place. Microphone, back Battery door Microphone, front To turn on a mic: Press the power button on its front. The mic automatically connects wirelessly to the Center Stage and its power button illuminates. (These buttons illuminate in different colors for each mic when you turn them on.) IMPORTANT: Make sure the mic’s volume slider is all the way up! To adjust the volume of your mic: Slide your mic’s volume slider up or down. To adjust the volume of both mics: Use the dial on the front of the Center Stage. To adjust the volume of your music: Use the volume controls on your Bluetooth device. To adjust the volume of everything: Use the knob on the front of the Center Stage, or press + or – on the remote. Power button Volume slider 7 Using Voice/Sound Effects and EQ To change voice effects: Press the button on the Center Stage or remote. Keep pressing to try all the effects! To add/adjust voice echo: Use the dial on the front of the Center Stage To use sound effects: Press the button on the Center Stage or remote. A single press plays the same effect again. Press and hold to change effects. To adjust sound EQ: Press the button on the Center Stage or remote to cycle through the EQ settings (rock, vocals, and flat). To p Using Dynamic Lighting The (lighting) and (color) buttons on top of the Center Stage give you control over the built-in dynamic lighting, as do the same buttons on the remote. Press the button to cycle through the multiple lighting modes. To p continues on the next page... 8 Tour of the Center Stage button cycles through the different EQ settings for the Center Stage (rock, vocals, and flat). button turns the Center Stage on/off (press and hold) a…

Text truncated - open the document above for the full version.

Important Information for Singsation Model SPKAW740M2, SPKAW740M CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. WARNING: Only use attachments/accessories specified by the manufacturer. 11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Care and Maintenance • Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol or other solvents as they may damage the surface. • Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock. • If the speaker is used outside on a deck or patio, make sure you take it indoors in the event of a rainstorm to prevent possible damage. The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. WARNING: The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable. Do not install this equipment in a confined space such as a book case or similar unit. The ventilation should not be impeded by covering the ventilation openings with Items such as newspaper, table-cloths, curtains etc. WARNING: The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Care is required with the use of this apparatus in moderate climates. See marking on the back of the product. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by VOXX Accessories Corporation could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement – for the speaker This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement – for the wireless microphones This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Regulatory Information This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Industry Canada Regulatory Information Avis d’Industrie Canada CAN ICES-3 (B)/NMB-3 (B) CAN ICES-3 (B)/NMB-3 (B) IC Radiation Exposure Statement – for the speaker This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. IC Radiation Exposure Statement – for the wireless microphones This equipment complies with IC r…

Text truncated - open the document above for the full version.

Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Voxx Accessories Corp. Address 3502 Woodview Trace Suite 220 Indianapolis Indiana 46268 United States Grantee Code VIX FCC ID VIXSPKAW740M2 Authorized Contact Name Paul Tinaphong Contact Email [email protected] Contact Phone (317)2187301 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List [Voxx Accessories Corp.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Voxx Accessories Corp.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date: 06/13/2023 Print Name: Paul Tinaphong Title: Senior V.P. *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

UNITED STATES DESIGNATED AGENT LETTER Date: 06/13/2023 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant U.S. designated agent Company Name: Voxx Accessories Corp. Company Name: Voxx Accessories Corp. Grantee Code: VIX FRN: 0016753550 Contact Name: Paul Tinaphong Contact Name: Paul Tinaphong Address: 3502 Woodview Trace Suite 220 Address: 3502 Woodview Trace Suite 220 City/Province/Zip: Indianapolis Indiana 46268 United States City/Province/Zip: Indianapolis Indiana 46268 United States Telephone: (317)2187301 Telephone: (317)2187301 Fax: (317)5691307 Fax: (317)5691307 Email: [email protected] Email: [email protected] Applicable Equipment: FCC ID: VIXSPKAW740M2 ATTN: Director of Certification: We, <Voxx Accessories Corp.> understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, <Voxx Accessories Corp.> acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Paul Tinaphong Name (Printed): Paul Tinaphong Title: Senior V.P. Title: Senior V.P. Signature: Signature:

Date: 06/13/2023 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: VIXSPKAW740M2 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Voxx Accessories Corp. This authorization is valid until further written notice from the applicant. Sincerely, Print Name: Paul Tinaphong Title: Senior V.P. Signature: On behalf of Company: Voxx Accessories Corp. Telephone: (317)2187301 E-mail: [email protected]

To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: VIXSPKAW740M2 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: Paul Tinaphong Title: Senior V.P. Signature: On behalf of Company: Voxx Accessories Corp. Telephone: (317)2187301 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 1 of 5 Appendix External Photos for SZCR2306001808AT FCC ID:VIXSPKAW740M2 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 2 of 5 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 3 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 4 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 5 of 5 - End of the Appendix -

建朗电子 制图 A 比例 编号 承 认 （三角） 绘图方法 单位 检 图 版号 材质 重 量 日 期 表面处理 名称 22 3 11 年 月 日 注 明 订正记录 2023-05-19 袁海涛 音箱底面 1.65A Made in China/Fabriqué en Chine IC: 21578-SPKAW740M2 FCC ID: VIXSPKAW740M2 Input/Entrée: 14.5V Model/Modèle: SPKAW740M2 64.5 74.5 SN:SGA233AB20A0001 4 26 This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference thatmay cause undesired operation.Cet appareil est conforme à la partie 15 du règlement de la FCC. Lefonctionnement est sujet aux deux conditions suivantes: (1) Cet appareil ne doitpas provoquer de brouillage préjudiciable et (2) cet appareil doit accepter tout brouillage reçu, y compris le brouillage susceptible de provoquer unfonctionnement indésirable. CAN ICES-003 (B)/NMB-003 (B)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 1 of 6 Appendix Internal Photos for SZCR2306001808AT FCC ID:VIXSPKAW740M2 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 2 of 6 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 3 of 6 Module 1 Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 4 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 5 of 6 Module 2 Antenna Module 3 Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 6 of 6 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600180805 Page: 1 of 11 Keny Xu EMC Laboratory Manager RF EXPOSURE EVALUATION REPORT Application No.: SZCR2306001808AT Applicant: Voxx Accessories Corp. Address of Applicant: 3502 Woodview Trace Suite 220, Indianapolis, Indiana, 46268, United States Manufacturer: Voxx Accessories Corp. Address of Manufacturer: 3502 Woodview Trace Suite 220, Indianapolis, Indiana, 46268, United States Factory: Smart Glory Electronics (ShenZhen) Co., Ltd Address of Factory: Building Four, No.63, Zhangqi Road, Qiping Village, Daping Community, Guanlan Street, Longhua District, Shenzhen Equipment Under Test (EUT): EUT Name: Center Stage Freestyle All-in-One Karaoke System Model No.: SPKAW740M2 Trade Mark: SINGSATION FCC ID: VIXSPKAW740M2 Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2023-06-09 Date of Evaluation: 2023-06-12 to 2023-06-30 Date of Issue: 2023-07-04 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600180805 Page: 2 of 11 Revision Record Version Chapter Date Modifier Remark 01 2023-07-04 Original Authorized for issue by: Charlie Dai/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600180805 Page: 3 of 11 2 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Contents .................................................................................................................................................... 3 3 General Information .................................................................................................................................. 4 3.1 General Description of E.U.T. ............................................................................................................ 4 3.2 Details of E.U.T. ................................................................................................................................. 4 3.3 Separation Distance ........................................................................................................................... 4 3.4 Test Location ...................................................................................................................................... 5 3.5 Test Facility ........................................................................................................................................ 5 3.6 Deviation from Standards ................................................................................................................... 5 3.7 Abnormalities from Standard Conditions ........................................................................................... 5 4 FCC Radiofrequency radiation exposure limits .................................................................................... 6 4.1 Blanket 1 mW Blanket Exemption ...................................................................................................... 6 4.2 MPE-based Exemption ...................................................................................................................... 6 4.3 SAR-based Exemption ....................................................................................................................... 7 5 Measurement and Calculation ............................................................................................................... 10 5.1 Maximum transmit power ................................................................................................................. 10 5.2 RF Exposure Calculation ................................................................................................................. 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600180805 Page: 4 of 11 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. Power supply: Center Stage powered by adapter Model：NLD165145W1A5S68 Input：100-240V 50/60Hz 0.6A Max. Output: 14.5V/1.65A Cable(s): Adapter dc cable 149cm unshielded without ferrite core Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: Module1: V5.2 Classic Module 2&3: V5.1 Classic Modulation Type: GFSK, pi/4DQPSK, 8DPSK Number of Channels: 79 Channel Spacing: 1MHz Spectrum Spread Technology: Frequency Hopping Spread Spectrum(FHSS) Antenna Type: Module1:PCB Antenna; module 2&3: Wire antenna Antenna Gain: Center Stage: module1: 0.99dBi; module 2: 0dBi; module 3: 0dBi Remark: The information in this section is provided by the applicant or manufacturer, SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. 3.3 Separation Distance Minimum test separation distance: 20cm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600180805 Page: 5 of 11 3.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.5 Test Facility The test facilit…

Text truncated - open the document above for the full version.

CustomerName:SHENZHENSHIXINZHONGXINTECHNOLOGY.CO.,LTD ProductName:BTAntenna SampleModel:SPKA740 ReferenceStandard:GB/T9410-2008;ANSI/IEEEStd149-1979 IssueDate:2023.06.16 Engineer: Date:2023.06.16 Auditor: Date:2023.06.16 Approver: Date:2023.06.16 TestingReport 1.GeneralInformation 1.1GeneralInformationoftestinginstitutions Name ShenzhenHetuoTechnologyCo.,Ltd. Addres s Room1202B,BuildingC6,HengfengIndustrialCity,Xixiang,Ba oanDistrict,Shenzhen Tel 18665849001 E-mail [email protected] Equipm ent Agilent5071C 1.2Testingprinciple Multi-probeOTAMeasurementSystem 1.3Testequipment EquipmentModelNo.SerialNo.Manufacturer Calibration date Next calibration date 24probe microwave chamber 4*3*3NAFEITU2023.05.292023.08.31 Network Analyzer 5071CNA Agilent 2023.05.292023.08.31 1.4Testenvironment Temperature 24°C±1.5°C Humidity 45%RH Pressure 101kPa 1.5 AntennaPhoto&Lenght(mm) 2.SampleInformation 2.1Clientinformation Name SHENZHENSHIXINZHONGXINTECHNOLOGY.CO.,LTD Address A1,ShajingDonghuanIndustrialZone,Bao'anDistrict,Shenzhen Contacts MaChao Tel 18218809918 E-mail [email protected] 2.2DescriptionofEUT(S) ProductName BTAntenna SampleModel SPKA740 AntennaSize 8.4*22.6mm AntennaType PCBantenna SerialNo. / TestItem AntennaGain,Radiationpattern FrequencyRange 2400-2500MHz ReceivedDate 2023.06.13 TestDate 2023.06.16 Remark ThelengthoftheRFcableis50mm Testdata Frequency (MHz) 2400.02410.02420.02430.02440.02450.02460.02470.02480.02490.02500.0 Gain(dBi) 0.800.590.750.990.920.700.670.570.820.951.12 Efficiency(%)54.0956.2254.2254.4254.3951.9851.1551.5050.0652.5453.18 Thetestphotos

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600180804 Page: 1 of 218 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2306001808AT Applicant: Voxx Accessories Corp. Address of Applicant: 3502 Woodview Trace Suite 220, Indianapolis, Indiana, 46268, United States Manufacturer: Voxx Accessories Corp. Address of Manufacturer: 3502 Woodview Trace Suite 220, Indianapolis, Indiana, 46268, United States Fac…

Text truncated - open the document above for the full version.