VKB271830BR10

ReefLink Regulatory and Safety Information Safety Statements:  Do not operate any appliance if it has a damaged cord or plug, if it is malfunctioning or if it is dropped or damaged in any manner.  Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.  Do not use appliance for other than intended use. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition.  Do not install or store the appliance where it will be exposed to weather or to temperatures below freezing.  If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.  Danger: To avoid possible electrical shock, special care should be taken since water is employed in the use of aquarium equipment.  DO NOT attempt repairs yourself; return the appliance to the manufacturer for service or discard.  DO NOT immerse in water. If the appliance falls into the water, DON’T reach for it! First unplug it and then retrieve it. If electrical components of the appliance get wet, unplug the appliance immediately FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Any changes or modifications not expressly approved by EcoTech Marine could void the user’s authority to operate the ReefLink. The user is cautioned to maintain a 20cm (8 inch) from the product to ensure compliance with FCC requirements. Industry Canada Compliance Statement: This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil. European Union – Disposal Information: According to local laws and regulations, your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. Some collection points accept products for free. The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. CE Declaration of Conformity: The equipment complies with the RF Exposure Requirement 1999/5/EEC, Council Recommendation on the limitation of exposure of the general public to electromagnetic fields (0‐300 GHz). This equipment meets the following conformance standards: EN 300 328, EN 301 489‐17, EN 60950 CE Declaration of Conformity in Languages of the European Community: Česky [Czech]: EcoTech Marine tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish]: Undertegnede EcoTech Marine erklærer herved, at følgende udstyr Enhed overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German]: Hiermit erklärt EcoTech Marine, dass sich das Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian]: Käesolevaga kinnitab EcoTech Marine seadme vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English: Hereby, EcoTech Marine declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish]: Por medio de la presente EcoTech Marine declara que el dispositivo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek]: ΜΕ ΤΗΝ ΠΑΡΟΥΣΑEcoTech Marine ΔΗΛΩΝΕΙ ΟΤΙ συσκευή ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French]: Par la présente EcoTech Marine déclare que l'appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian]: Con la presente EcoTech Marine dichiara che questo dispositivo è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian]: Ar šo EcoTech Marine deklarē, ka ierīce atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian]: Šiuo EcoTech Marine deklaruoja, kad šis prietaisas atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch]: Hierbij verklaart EcoTech Marine dat het toestel apparaat in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese]: Hawnhekk, EcoTech Marine, jiddikjara li dan apparat jikkonforma mal‐ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid‐Dirrettiva 1999/5/EC. Magyar [Hungarian]: Alulírott, EcoTech Marine nyilatkozom, hogy a eszköz megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish]: Niniejszym EcoTech Marine oświadcza, że urządzenie jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese]: EcoTech Marine declara que este dispositivo está conforme com o…

Text truncated - open the document above for the full version.

WTD 13.4.9 FCC Compliance Opinion ECTE0014 Information about the Applicant Grantee (Company Name) EcoTech Marine FCC Contact Person Justin Lawyer Address 1349 Lynn Ave. City, State, Zip Bethlehem, PA 18015 Job Number ECTE0014 Model ReefLink BR-10 FCC ID VKB271830 Agent NA Approval Type Original Equipment Class DTS Digital Transmission System Rule Part 15.247 (15C) Overview The Ecotech Marine Reeflink model BR10 contains two previously certified radio modules, a Qualcomm Atheros 802.11 b/g/n radio FCC ID PPD-AR4100 and an EcoTech Marine radio FCC ID: VKB271829. The BR10 device will use the 802.11 b/g/n radio to communicate with the internet and the EcoTech Marine radio to communicate with other EcoTech Marine products. Confidentiality requested for allowed files. Request is properly addressed and referenced. Short term confidentiality requested. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 11/6/2013

Page 1 CONSTRUCTION PHOTOS OF EUT

EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax External Photos: Top: Bottom: EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Front: Back: EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Side Views:

EcoTech Marine 1349 Lynn Ave Bethlehem, PA 18015 610.954.8480 office 888.500.2907 fax External Photos: Component Side (with RF Shield): Component Side (without RF Shield): RF Shield Connectors to end product main board Antenna Feed Via EcoTech Marine 1349 Lynn Ave Bethlehem, PA 18015 610.954.8480 office 888.500.2907 fax Back Side: Side Views (without RF Shield): PCB Antenna EcoTech Marine 1349 Lynn Ave Bethlehem, PA 18015 610.954.8480 office 888.500.2907 fax Side Views (with RF Shield):

EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax FCC Label and Location: Label: Location – Bottom of Device: EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax

Page 2 EUT + PIFA antenna PIFA antenna EUT EUT IPEX connector Page 3 PIFA antenna PIFA antenna Page 4 PIFA antenna Page 5 EUT + CHIP antenna EUT + PCB antenna CHIP antenna EUT PCB antenna EUT

EcoTech Marine 1349 Lynn Ave Bethlehem, PA 18015 610.954.8480 office 888.500.2907 fax Internal Photos: Component Side (with RF Shield): Component Side (without RF Shield): RF Shield Connectors to end product main board Antenna Feed Via EcoTech Marine 1349 Lynn Ave Bethlehem, PA 18015 610.954.8480 office 888.500.2907 fax Back Side: Side Views (without RF Shield): PCB Antenna EcoTech Marine 1349 Lynn Ave Bethlehem, PA 18015 610.954.8480 office 888.500.2907 fax Side Views (with RF Shield):

EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Internal Photos: Main PCBA Top: Main PCBA Top with Sections Identified: Qualcomm Atheros Wifi Radio Section Main Microcontroller Section Ethernet Section USB Section DC‐DC Switching Re gulator AC‐DC Power Supply Section EcoTech Marine 10169 Radio User Interface LED Section EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Main PCBA Bottom: Main PCBA Bottom with Section Identified Micro SD Card Under Main Microcontroller Under Wifi Section Under EcoTech Marine Radio Section EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Main PCBA Qualcomm Atheros Wifi Section Top: Main PCBA Qualcomm Atheros Wifi Section Bottom: PCB Antenna PCB Antenna EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Main PCBA EcoTech 10169 Radio Section with Radio Placed: : Main PCBA EcoTech 10169 Radio Section with Radio Removed: PCB Antenna EcoTech Marine 999 Postal Road, Suite 100 Allentown, PA 18109 610.954.8480 office 888.500.2907 fax Main PCBA AC‐DC Power Supply Section: Main PCBA Placed Inside Top of Enclosure

EcoTech Marine Model: Reeflink BR-10 Report No. ECTE0014.2 FCC 2.1091:2013 Maximum Permissible Exposure Level Report Prepared By Northwest EMC Inc. NORTHWEST EMC – (888) 364-2378 – www.nwemc.com California – Minnesota – Oregon – New York – Washington 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Evaluation Date of Evaluation: October 28, 2013 EcoTech Marine Model: Reeflink BR-10 Emissions Description of Evaluation Specification Evaluation Method Pass/Fail Maximum Permissible Exposure FCC 2.1091:2013 KDB 447498 D01 General RF Exposure Guidance v05r01 Pass Approved By: Don Facteau, IS Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Report No. ECTE0014.22/9 REV 2012.08.02 REVISION HISTORY Revision Number Description Date Page Number 00 None Barometric Pressure The recorded barometric pressure has been normalized to sea level. Report No. ECTE0014.23/9 REV 2012.05.24 ACCREDITATIONS AND AUTHORIZATIONS United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC Guide 65 as a product certifier. This allows Northwest EMC to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada IC - Recognized by Industry Canada as a Certification Body (CB). Certification chambers and Open Area Test Sites are filed with IC. European Union European Commission – Validated by the European Commission as a Conformity Assessment Body (CAB) under the EMC directive and as a Notified Body under the R&TTE Directive. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea KCC / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Hong Kong OFTA – Recognized by OFTA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. Russia GOST – Accredited by Certinform VNIINMASH, CERTINFO, SAMTES, and Federal CHEC to perform EMC and Hygienic testing for Information Technology products to GOST standards. SCOPE For details on the Scopes of our Accreditations, please visit: http://www.nwemc.com/accreditations/ Report No. ECTE0014.24/9 REV 2013.02.26 LOCATIONS Oregon Labs EV01-12 22975 NW Evergreen Pkwy Hillsboro, OR 97124 (503) 844-4066 California Labs OC01-13 41 Tesla Irvine, CA 92618 (949) 861-8918 New York Labs NY01-04 4939 Jordan Rd. Elbridge, NY 13060 (315) 685-0796 Minnesota Labs MN01-08 9349 W Broadway Ave. Brooklyn Park, MN 55445 (763) 425-2281 Washington Labs NC01-05,SU02,SU07 19201 120 th Ave. NE Bothell, WA 98011 (425) 984-6600 VCCI A-0108 A-0029 A-0109 A-0110 Industry Canada 2834D-1, 2834D-2 2834B-1, 2834B-2, 2834B-3 2834E-1 2834C-1 NVLAP NVLAP Lab Code: 200630-0 NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200761-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200629-0 Report No. ECTE0014.25/9 Product Description Revision 09/01/11 Client and Equipment Under Test (EUT) Information Company Name: EcoTech Marine Address: 999 Postal Road City, State, Zip: Allentown, PA 18109 Test Requested By: Mark Lindenmoyer Model: Reeflink BR-10 Date of Evaluation: October 28, 2013 Information Provided by the Party Requesting the Test Functional Description of the EUT (Equipment Under Test): ReefLink is a wireless bridge that seamlessly integrates the Radion with the web-based EcoSmart Live platform to provide complete custom control of aquarium lighting. The EUT contains an 802.15.4 Zigbee DTS radio (FCC ID: VKB271829) which is co-located with an Atheros 802.11b/g Wi-Fi radio (FCC ID: PPD-AR4100). Objective: To demonstrate compliance of the radio with FCC requirements for RF exposure for 2.1091 mobile devices. Report No. ECTE0014.26/9 WD.12.29.11 Maximum Permissible Exposure (MPE) OVERVIEW Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. ANSI C95.1-1992 specifies a minimum separation distance of 20 cm for performing reliable field measurements to determine adherence to MPE limits. If the minimum separation distance between a transmitter and nearby persons is more than 20 cm under normal operating conditions, compliance with MPE limits may be determined at such distance from the transmitter. When applicable, operation instructions and prominent warning labels may be used to alert the exposed persons to maintain a specified distance from the transmitter or to limit their exposure durations and usage conditions to ensure compliance. If the use of warning labels on a transmitter is not effective or desirable, the alternative of performing SAR evaluation with the device at its closest range to persons under normal operating conditions may be used. The field strength and power density limits adopted by the FCC are based on whole-body averaged exposu…

Text truncated - open the document above for the full version.

Report No.: RF110505E05 R1 1 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110505E05 dated June 10, 2011 FCC TEST REPORT REPORT NO.: RF110505E05 R1 MODEL NO.: AR4100 FCC ID: PPD-AR4100 IC ID: 4104A-AR4100 RECEIVED: May 05, 2011 TESTED: May 27 to June 07, 2011 ISSUED: June 15, 2011 APPLICANT: Qualcomm Atheros,Inc. ADDRESS: 1700 Technology Drive, San Jose, CA 95110 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No.49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 145 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF110505E05 R1 2 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110505E05 dated June 10, 2011 Table of Contents RELEASE CONTROL RECORD........................................................................................5 1. CERTIFICATION....................................................................................................6 2. SUMMARY OF TEST RESULTS............................................................................7 2.1 MEASUREMENT UNCERTAINTY..........................................................................8 3. GENERAL INFORMATION.....................................................................................9 3.1 GENERAL DESCRIPTION OF EUT.......................................................................9 3.2 DESCRIPTION OF ANTENNA.............................................................................11 3.3 DESCRIPTION OF TEST MODES.......................................................................12 3.3.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL........................13 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................16 3.5 DESCRIPTION OF SUPPORT UNITS..................................................................17 3.6 CONFIGURATION OF SYSTEM UNDER TEST...................................................18 4. TEST TYPES AND RESULTS..............................................................................19 4.1 CONDUCTED EMISSION MEASUREMENT........................................................19 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT......................................19 4.1.2 TEST INSTRUMENTS..........................................................................................19 4.1.3 TEST PROCEDURES..........................................................................................20 4.1.4 DEVIATION FROM TEST STANDARD.................................................................20 4.1.5 TEST SETUP.......................................................................................................21 4.1.6 EUT OPERATING CONDITIONS.........................................................................21 4.1.7 TEST RESULTS...................................................................................................22 4.2 RADIATED EMISSION MEASUREMENT.............................................................24 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...........................................24 4.2.2 TEST INSTRUMENTS..........................................................................................26 4.2.3 TEST PROCEDURES..........................................................................................27 4.2.4 DEVIATION FROM TEST STANDARD.................................................................27 4.2.5 TEST SETUP.......................................................................................................28 4.2.6 EUT OPERATING CONDITIONS.........................................................................28 4.2.7 TEST RESULTS (For transmitter part)..................................................................29 4.2.7.1 TEST RESULTS (With PIFA Antenna)..................................................................29 4.2.7.2 TEST RESULTS (With Chip Antenna)...................................................................51 4.2.7.3 TEST RESULTS (With PCB Antenna)...................................................................73 4.2.8 TEST RESULTS (For receiver part)......................................................................95 4.2.8.1 TEST RESULTS (With PIFA Antenna)..................................................................95 4.2.8.2 TEST RESULTS (With Chip Antenna)...................................................................99 4.2.8.3 TEST RESULTS (With PCB Antenna).................................................................103 4.3 6dB BANDWIDTH MEASUREMENT..................................................................107 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT................................................107 Report No.: RF110505E05 R1 3 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110505E05 dated June 10, 2011 4.3.2 TEST INSTRUMENTS........................................................................................107 4.3.3 TEST PROCEDURE...........................................................................................108 4.3.4 DEVIATION FROM TEST STANDARD...............................................................108 4.3.5 TEST SETUP.....................................................................................................108 4.3.6 EUT OPERATING CONDITIONS........................…

Text truncated - open the document above for the full version.

EcoTech Marine RF Module 10169 Report No. ECTE0002 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2009 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: October 08, 2009 EcoTech Marine Model: RF Module 10169 Emissions Test Description Specification Test Method Pass/Fail Spurious Radiated Emissions FCC 15.247 (DTS):2009 ANSI C63.4:2003 KDB No. 558074 Pass Spurious Conducted Emissions FCC 15.247 (DTS):2009 ANSI C63.4:2003 KDB No. 558074 Pass Occupied Bandwidth FCC 15.247 (DTS):2009 ANSI C63.4:2003 KDB No. 558074 Pass Output Power FCC 15.247 (DTS):2009 ANSI C63.4:2003 KDB No. 558074 Pass Band Edge Compliance FCC 15.247 (DTS):2009 ANSI C63.4:2003 KDB No. 558074 Pass Power Spectral Density FCC 15.247 (DTS):2009 ANSI C63.4:2003 KDB No. 558074 Pass AC Powerline Conducted Emissions FCC 15.207:2009 ANSI C63.4:2003 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR Phone: (763) 425-2281 Fax: (763) 424-3469 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-1). Approved By: Don Facteau, IS Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 06/29/09 Revision Number Description Date Page Number 00 None Barometric Pressure The recorded barometric pressure has been normalized to sea level. Accreditations and Authorizations FCC Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP Northwest EMC, Inc. is accredited under the United States Department of Commerce, National Institute of Standards and Technology, and National Voluntary Laboratory Accreditation Program for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. NVLAP LAB CODE 200629-0 NVLAP LAB CODE 200630-0 NVLAP LAB CODE 200676-0 NVLAP LAB CODE 200761-0 NVLAP LAB CODE 200881-0 Industry Canada Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. (Site Filing Numbers - Hillsboro: 2834D-1, 2834D-2, Sultan: 2834C-1, Irvine: 2834B-1, 2834B-2, Brooklyn Park: 2834E-1) CAB Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. NEMKO Assessed and accredited by NEMKO (Norwegian testing and certification body) for European emissions and immunity testing. As a result of NEMKO's laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification (Authorization No. ELA 119). Accreditations and Authorizations Australia/New Zealand The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). VCCI Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (Registration Numbers. - Hillsboro: C-1071, R-1025, C-2687, T-289, and R-2318, Irvine: R-1943, C-2766, and T- 298, Sultan: R-871, C-1784, and T-294, Brooklyn Park: R-3125, C-3464, and T-1634). BSMI Northwest EMC has been designated by NIST and validated by C-Taipei (BSMI) as a CAB to conduct tests as described in the APEC Mutual…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST (With PIFA antenna) 3 4 RADIATED EMISSION TEST (With Chip antenna) 5 6 RADIATED EMISSION TEST (With PCB antenna) 7

NORTHWEST EMC OCCUPIED BANDWIDTH XMit 2009.03.05 NORTHWEST EMC OUTPUT POWER XMit 2009.03.05 NORTHWEST EMC BAND EDGE COMPLIANCE XMit 2009.03.05 NORTHWEST EMC SPURIOUS CONDUCTED EMISSIONS XMit 2009.03.05 NORTHWEST EMC POWER SPECTRAL DENSITY XMit 2009.03.05 NORTHWEST EMC SPURIOUS RADIATED EMISSIONS PSA 2008.07.21 NORTHWEST EMC SPURIOUS RADIATED EMISSIONS PSA 2008.07.21 NORTHWEST EMC SPURIOUS RADIATED EMISSIONS PSA 2008.07.21 NORTHWEST EMC CE 001.jpg CE 002.jpg AC Powerline Conducted Emissions PSA-ESCI 2009.06.09 NORTHWEST EMC CE 003.jpg AC Powerline Conducted Emissions PSA-ESCI 2009.06.09