VPE-STG-866BAsset Tracking Tag

SmartTag STG-866B User Manual CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 2 Contents 1 Introduction ................................................................................................................................................ 10 2 Location Reporting Method ....................................................................................................................... 10 3 Mounting Method ...................................................................................................................................... 11 4 Specifications .............................................................................................................................................. 12 5 Battery Change Instructions ....................................................................................................................... 13 6 Trouble-shooting Guide .............................................................................................................................. 16 CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 3 Regulatory Information Product Name: SmartTag Model: STG-866B FCC ID: VPE-STG-866B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Cadi Scientific Pte Ltd 31 Ubi Road 1 #09-01 Singapore 408694 Singapore CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 4 PRECAUTIONS • Keep batteries away from children. • Do not swallow batteries. • Do not throw batteries into water. • Do not throw batteries into fire. • Do not short-circuit batteries. Battery must be fit into tag in correct orientation. • Do not replace battery with incorrect type. Incorrect type of battery replacement may cause risk of exposure. • Battery should be dispose according to the instructions Product Information • Product model : STG-866B • Product name : SmartTAG • Manufacturing site : 31 Ubi Road 1, #09-01 Annex Building, Singapore 408694 User Manual Version Information • This version is subject to change or upgrade without notice • Version : 2 • Issue date : 16 Jan 2023 Declaration Cadi Scientific Pte Ltd reserves the right to change the product described in this User Manual. All information contained in this User Manual is subject to change without notice. CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 10 1 Introduction The STG-866B is a battery powered location tracking tag. Location tracking is achieved using a combination of technologies based on low frequency (LF), infrared (IR), and BLE signals that give robust performance even in challenging environments. 2 Location Reporting Method When the STG-866B passes by a LF beacon or exciter (typically installed at key chokepoints or egress points) it will receive over its LF receiver a location ID transmitted by the LF beacon. The tag will then advertise this location ID over its BLE transmitter. Access points that are in range of STG-866B’s advertisements will be able to receive STG-866B’s location. When the STG-866B enters a room that has a IR beacon installed, the tag will receive a location ID transmitted by the IR beacon. The tag will then advertise this location ID over its BLE transmitter. Access points that are in range of STG-866B’s advertisements will be able to receive STG-866B’s location. CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 11 3 Mounting Method The tag can be mounted on assets or equipment using a mounting bracket accessory. CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 12 4 Specifications S/N Feature Description 1 Physical Dimension Weight 42.5mm x 70mm x 23mm TBC 2 Power Rechargeable User replaceable Battery type No Yes 3.6v (ER17335-2 3.6V LiSOCl 2 primary battery) 3 Operating Environment Temperature Humidity 0 o C to 55 o C 0 – 95% RH non-condensing 4 RF Specifications Frequency 2.4GHz (standard advertising channels) 5 LF Receiver Specifications Frequency 125kHz (receive only) 6 IR Receiver Specifications Frequency 38kHz (receive only) 7 Location-Update/Beacon Update rate Immediate upon detection of LF or IR location ID 8 Interface Visual Audio 1 x Red LED 1 x Green LED 1 x Beeper 9 Compliance RF To be confirmed EMC To be confirmed Safety To be confirmed CONFIDENTIAL CADI SmartSense – SmartTag STG-866B User Manual v2 13 5 Battery Change Instructions 5.1 Remove rear battery cover - Pry at the rear cover at the 2 release points using a flat tip screw driver 5.2 Disconnect depleted battery (1) Remove battery from tag to make room (2) Apply straight pulling or tugging action t…

Text truncated - open the document above for the full version.

Certification designating a U.S. Agent for service of process: As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must: i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicant’s consent and the designated agent’s obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicant’s acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Unofficial information provided by FCC personnel on February 14, 2023, via the monthly call with the TCB Council: The Agent for Process of Service: • cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB) • cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab) • Agent can be Individual Entity or a Company Entity • Agent Entity must be located in US, US address/phone • Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter) • Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and/or the agent who may interface with the TCB. U.S. Agent Designation for Service of Process ATTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Approve-IT, Inc. Contact Name: Nathan Grinager Street Address: 8011 34 th Ave South, Suite 342 City/Province/Zip: Bloomington, MN 55425 Telephone No: 651-247-1678 Email: [email protected] FRN #: 0027533835 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: June 1, 2023 Signed by (Printed Name/Title): Nathan Grinager / Co-President *This letter is valid indefinitely for all applications submitted within the period of 06/01/2023 – 05/31/2024. The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Cadi Scientific Pte Ltd Grantee Code: VPE FCC ID: VPE-STG-866B Contact Name: Ng Hon Cheong Street Address: 31 Ubi Road 1, #09-01, S(408694), Singapore City/Province/Zip: Singapore Telephone No: +65 62762676 Email: [email protected] Applicant Signature: Date: 1/6/2023 Signed by (Printed Name/Title): Ng Hon Cheong

Declaration of Product Usage Instruction Product Information Model: STG-866B FCC ID: VPE-STG-866B Declaration of Product Usage Instruction This is to declare that the product usage instruction for STG-866B meets all use requirements of the certified module FCC ID: RFR-S50. The original test reports are accurately represented test results under the new conditions. This product is referenced to the module (FCC ID: RFR-S50) test report number 1-5687/17-01-07. The module used in this product is the PMN: BlueMod+S50/AI version, that is the version with internal ceramic antenna chip. There is no other external antenna. Yours sincerely, Name: Ng Hon Cheong Telephone Number: +65 62762676 Email: [email protected]

Date: 06-26-2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) Filing Re. KDB 986446 D01 FCC ID: VPE-STG-866B Dear Sir or Madam, Cadi Scientific Pte Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please contact us. Sincerely, Contact name: Ng Hon Cheong Company name: Cadi Scientific Pte Ltd Address: 31 Ubi Road 1, #09-01, Singapore 408694, Singapore E-mail: [email protected] Tel: +65 62762676

Cadi Scientific Pte Ltd Date (06/26/2023) TUV SUD America Inc. 10 Centennial Drive Peabody, MA 01960, USA Dear Sir or Madam, We, Cadi Scientific Pte Ltd 31 Ubi Road 1, #09-01, Singapore 408694 hereby authorize Cathy Huang from TUV SUD Certification and testing (China) Co., Ltd. Guangzhou Branch, address is 5F, Communication Building, 163 Pingyun Rd, Huangpu West Ave. Guangzhou 510656 P. R. China, phone is +86 20 3817 0729, to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. Type of equipment: Asset Tracking Tag Model name: STG-866B FCC ID: VPE-STG-866B This authorization expires on 06/26/2024. Yours sincerely, Name: Ng Hon Cheong Telephone Number: +65 62762676 Email: [email protected]

Cadi Scientific Pte Ltd Date (06/26/2023) Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request FCC ID: VPE-STG-866B Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, Cadi Scientific Pte Ltd hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Name: Ng Hon Cheong Telephone Number: +65 62762676 Email: [email protected]

Data sheet of Multilayer Chip Antenna Part No. : ALA621C4 January 23, 2008 AMOTECH Co., LTD. 5B 1L, Namdong Industrial complex, 617 Namchondong, Namdonggu, Incheon, Korea Notes The contents of this data sheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. AMOTECH - 2 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 1. SPECIFICATIONS 1.1 Electrical Specifications No ITEM SPEC. Remark 1 Frequency Range 2.4 ~2.485 GHz for ISM 2 VSWR 2.5 : 1 max. 3 Gain Avg. -3 dBi min. 4 Polarization Linear 5 Azimuth Beam Pattern Omni-directional 6 Impedance Nominal 50 Ω ※ These values are measured on the matched reference test board. 1.2 Mechanical Specifications No ITEM Spec. Remark 1 Internal Electrode Ag Pb-free 2 External Electrode Ag/Ni/Sn Pb-free 3 Dimensions (L x W x H) 6 x 2 x 1.2 mm 4 Unit Weight 46 ± 4 mg 5 Operating Temperature -35 ~ +85 °C 1.3 Appearance and Dimensions No Name Function Material 1 External Electrode Soldering, Input Port Ag/Ni/Sn 2 Direction index Indication of Input Port Ceramic 3 Model & Serial No. index - Ceramic 4 Ceramic Body - Ceramic 5 External Electrode Soldering Ag/Ni/Sn AMOTECH - 3 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 2. MEASUREMENT 2.1 Reference Test Board for Measurement 2.2 Diagram for VSWR measurement Network Analyzer Styrofoam AUT AMOTECH - 4 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 2.3 Diagram for radiation gain and pattern measurements iMac A. Anechoic chamber spec. Parameters Condition Unit Chamber size 8x4x4 m Temperature 21.5 °C Humidity 55 % RH Measurement S21 (8753ES) System software Midas (Orbit/FR) B. Measurement coordinates Measurement Plane Symbol Rotating direction Azimuth Azimuth x→y Elevation1 E1 z→x Elevation2 E2 z →-y x y z -y Azimuth E1 E2 AMOTECH - 5 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 3. MEASUREMENT RESULT 3.1 VSWR & Smithchart A. Matching Value (recommend for reference testboard only) ③① ② ① N/C ② 2.7 nH ③ 2.2 nH B. Measured data AMOTECH - 6 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 3.2 Radiation Gain and Pattern [Measured data table] Peak Gain (dBi) Average Gain (dBi) Remark Azimuth 2.6 0.7 @2.45 GHz Elevation1 3.5 -0.6 @2.45 GHz Elevation2 2.0 -1.7 @2.45 GHz [ ALA621C4 radiation pattern : [email protected] ] AMOTECH - 7 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) [ ALA621C4 radiation pattern : [email protected] ] [ ALA621C4 Radiation Pattern : [email protected] ] AMOTECH - 8 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 4. SUGGESTED LAYOUT & MATCHING CIRCUIT 4.1 Layout (recommend only) 4.2 Matching Circuit (recommend only) L – type T - type π- type For usable matching, the ground stability must be guaranteed with sufficient via holes and the case effects should be considered. Finally, using one or more lumped chip elements and a tuning stub are recommended for better results. AMOTECH - 9 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 5. RELIABILITY TEST No ITEM TEST CONDITION TEST REQUIREMENTS 1 Adhesive Strength of Termination 1. Applied force on SMD chip till detached point from PCB. F SMD PAD PCB 1. No mechanical damage by forces applied on the right. 2. Strength (F) > 5 kgf 2 Tensile Strength 1. Wire : 0.6~0.8 tined Cu wire F Clamp Wire 1. No mechanical damage by forces applied on the right. 2. Strength (F) > 3 kgf 3 Thermal Shock (Temperature Cycle) 1. 1 cycle / step 1 : -40 ± 3°C, 30 min step 2 : +125 ± 3°C, 30 min 2. Number of cycle : 30 3. Measure after left for 48 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) 4 High Temperature Resistance 1. Temperature : +125 ± 5°C 2. Time : 1000 ± 24 hrs 3. Measure f C after left for 24 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) 5 Low Temperature Resistance 1. Temperature : -40 ± 5°C 2. Time : 1000 ± 24 hrs 3. Measure f C after left for 48 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) 6 Humidity (Steady Condition) 1. Humidity : 85 % RH 1. Temperature : +85 ± 3°C 2. Time : 1000 ± 24 hrs 3. Measure f C after left for 48 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) AMOTECH - 10 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 6. SOLDERING RECOMMENDATIOS 6.1 Reflow Soldering Profile [ Soldering Reflow Profile for Pb-free ] 6.2 Soldering Land Pattern 7.0 1.1 2.2 4.8 (unit : mm) AMOTECH - 11 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 7. PACKING 7.1 Tape Dimension (unit : mm) A0 2.30±0.10 P0 4.00±0.10 E 1.75±0.10 B0 6.40±0.10 P1 4.00±0.10 F 7.50±0.10 K0 1.35±0.10 P2 2.00±0.10 W 16.00±0.30 D0 1.55±0.05 t 0.30±0.05 7.2 Taping Style 7.3 Packing Unit Quantity Size (mm 3 ) Reel 2,000 ea Φ7” * 16mm Small Box 6,000 ea (3 reel*2,000ea/reel) 185 * 185 * 68 (mm 3 ) Middle Box 30,000 ea (5 small box*6,000ea/small box) 365 * 200 * 200 (mm 3 ) Large Box 84,000 ea (14 small box*6,000ea/small box) 390 * 390 * 280 (mm 3 ) AMOTECH - 12 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 7.4 Description of Packing Label AMOTECH CO., LTD. Name of Company 617 5B 1LT, Namchon-Dong, Namdong-Gu, Inchon, Korea Address of Manufacture Multilayer Chip Antenna Name of Component Type : ALA621C4 Lot No : MA06A405011 Quantity : 2,000 pcs Quantity : 2,000 pcs Date : 2005/03/10 Date : 2006 /01 /24 8. STORAGE CONDITION A. Storage environment must be at an ambient temperature of 15~35°C and an ambient humidity of 45~75 % RH. (MSL Level 2) B. Chip antenna can experience degradation of termination solderability when subjected to high temperature of humidity, or if exposed to sulfur or chlorine gases. C. Avoid mechanical shock (ex. falling) to the chip antenna to prevent mechanical cracking inside of the ceramic dielectric due to its own weight. ALA : Amotech LTCC Antenna 621 : Chip Size C4 : Version & Frequency index MA : Mass-product Antenna 06 : Chip Size A4 : Version & Frequency index 0605 : Year / Month 11 : Order of production

LA-2007-0380-A LA-2007-0381-F LA-2007-0382-B LA-2007-0383-G LA-2007-0384-G LA-2007-0385-E LA-2007-0386-C LA-2010-0464-D LA-2018-0702-B LA-2018-0703-G LA-2020-0747-L The results reported herein have been performed in accordance with the terms of accreditation under the Singapore Accreditation Council. Inspections/Calibrations/Tests marked "Not SAC- SINGLAS Accredited" in this Report are not included in the SAC-SINGLAS Accreditation Schedule for our inspection body/laboratory. Laboratory: TÜV SÜD PSB Pte. Ltd. 15 International Business Park TÜV SÜD @ IBP Singapore 609937 Phone : +65-6778 7777 E-mail: [email protected] https://www.tuvsud.com/sg Co. Reg : 199002667R Regional Head Office: TÜV SÜD Asia Pacific Pte. Ltd. 15 International Business Park TÜV SÜD @ IBP Singapore 609937 Page 1 of 39 TÜV SÜD PSB PTE LTD RESPONSIBLE FOR NAME DATE SIGNATURE Approved By Foo Kai Maun 24 Mar 2023 Prepared By Quek Keng Huat 23 Mar 2023 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD PSB document control rules. EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with the mentioned standard(s). Report on the Radio Testing of: BATTERY POWERED LOCATION TRACKING TAG Model(s): STG-866B In accordance with 47 CFR FCC Part 15C Prepared for: Cadi Scientific Pte. Ltd. 31 Ubi Road 1 #09-01 Annex Building Singapore 408694 COMMERCIAL-IN-CONFIDENCE Document Number: 7191303564-EEC23/05 | Issue: 01 FCC ID: VPE-STG-866B Document Number: 7191303564-EEC23/05 | Issue: 01 FCC ID: VPE-STG-866B COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 2 of 39 Contents 1 Report Summary ..................................................................................................................... 3 1.1 Report Modification Record ....................................................................................................... 3 1.2 Introduction ............................................................................................................................... 4 1.3 Brief Summary of Results .......................................................................................................... 5 1.4 Product Information ................................................................................................................... 7 1.5 Deviations from the Standard .................................................................................................... 9 1.6 EUT Modification Record ........................................................................................................... 9 1.7 Test Location(s) ........................................................................................................................ 9 1.8 Test Facilities Registrations ....................................................................................................... 9 1.9 Supporting Equipment ............................................................................................................. 10 2 Test Details ............................................................................................................................ 11 2.1 Radiated Emissions (Spurious Emissions Inclusive Restricted Bands Requirement) ................ 11 2.2 Band Edge Compliance (Radiated) ........................................................................................... 16 2.3 Maximum Permissible Exposure (MPE) ................................................................................... 21 3 Photographs .......................................................................................................................... 24 4 Test Equipment ..................................................................................................................... 35 5 Measurement Uncertainty ..................................................................................................... 36 6 Annex A – FCC Label and Position ...................................................................................... 37 End of the Test Report ......................................................................................................................... 39 Page 3 of 39 Document Number: 7191303564-EEC23/05 | Issue: 01 FCC ID: VPE-STG-866B COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 3 of 39 1 Report Summary 1.1 Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Issue Description of Change Date of Issue 1 First Issue 24 Mar 2023 Page 4 of 39 Document Number: 7191303564-EEC23/05 | Issue: 01 FCC ID: VPE-STG-866B COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 4 of 39 1.2 Introduction Applicant : Cadi Scientific Pte. Ltd. 31 Ubi Road 1 #09-01 Annex Building Singapore 408694 Manufacturer : Same as applicant Factory : Same as applicant Model Number(s) : STG-866B Serial Number(s) : 00217EBD4A86 (TX@2402MHz) 00217EBD4A39 (TX@2426MHz) 00217EBD4F32 (TX@2480MHz) Number of Samples Tested : 1 Test Sample(s) Condition : Good Quotation Reference : 5781707 Test Specification/Issue/Date : FCC 47 CFR Part 15C Test Sample(s) Received Date : 08 Mar 2023 Start of Test : 08 Mar 2023 Finish of Test : 08 Mar 2023 Page 5 of 39 Document Number: 7191303564-EEC23/05 | Issue: 01 FCC ID: VPE-STG-866B COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 5 of 39 1.3 Brief Summary of Results A brief summary of the tests carried out in accordance with specifications as shown below. Specification Clause Test Description Result Comments/Base Standard 47 CFR FCC Part 15 15.107(a), 15.207 Conducted Emissions Not Applicable * See Note 4 ANSI C63.4: 2014 ANSI C63.10: 2013 KDB 558074 D01 DTS Measurement Guidance V05R02: 2018 15.109(a), 15.205, 15.209 Radiated Emissions (Spurious Emissions Inclusive Restricted Bands Requirement) Pass ANSI C63.4: 2014 ANSI C63.10: 2013 KDB 558074 D01 DTS Measurement Guidance V05R02: 2019 15.247(a)(2) Spectr…

Text truncated - open the document above for the full version.