VRBH913ETelematic Control Unit

Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 User manual for Telematics Control Unit H913E Ver 1.0 Sage Co.,Ltd. Nov 1, 2007 Date: 2007/11/1 Contact Information Masaki Mori Engineer [email protected] Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 TM Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 1 Contents GENERAL Safty Instructions 1. H913E data sheet 2. Appearance 3. Componets 4. Installation/Operation Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 2 General This document content describes the overview of the Telematics Control Unit H913E. The H913E is designed to operate only in the United States with GPRS (General Packet Radio Services) and EDGE (Enhanced Data rates for GSM Evolution) networks. Users do not need to operate the device directly because the device is fully automatic. However, users must comply with safety instructions. Please contact your sales representative of Honda America if you have any problems. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: - this device may not cause harmful interference, and - this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by SAGE Co., Ltd. may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 3 Safety instructions In August 1996, the Federal Communications Commission (FCC) of the U.S. adopted an updated safety standard for human exposure to the radio frequency electromagnetic energy emitted by FCC regulated transmitters. The design of this Car Telematics Control Unit complies with the FCC guidelines and those standards. The installation of the device is performing by the manufacturer at the rear window of the car and ensures at least 20cm distance to any person inside or outside of the car. Modifications or antenna replacement not expressly approved by, Honda R&D Co., Ltd. could void the user's authority to operate the equipment. To comply with RF safety requirements please follow the installation instructions provided by the manufacture and maintain a minimum separation distance of 20cm. from the antenna to any human body. Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 4 1 H913E data sheet Physical Size D138, W145, H35 Weight 330g (Without Antenna, Cable) Environment（without SIM card） Operating temperature -20 degrees C to +60 degrees C Storage temperature -40 degrees C to +85 degrees C Performance Maximum electric power consumption 630mA / 14V Standby electric power consumption 120mA / 14V Dark current electric power consumption Under 0.1mA Version Hardware version 1.00 Software version 1.00 Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 5 2 Appearance Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 6 3 Components 1: Telecommunication module (g24 E) 2: SIM socket 3: CAN (Car Area Network) connector, Power connector 4: Antenna connector 1 2 3 4 Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yokohama City Kanagawa Pref 231-0007 7 4 Installation/Operation 4.1 Installtion H913E is installed at the left side of the trunk. All installation is performed by authorized Honda America engineers, and the user of the car will not be installing or touching the device at any conditions. 4.2 Opration Users do not need to operate H913E directory because H913E is a full automatic. H913E will be turned on when the car ignition is on.

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Date: 2007-11-16 TO WHOM IT MAY CONCERN FCC ID: VRBH913E granted on 2007-11-15 By accident the Tune Up Information was uploaded as exhibit type RF Exposure Info. We kindly ask you to supercede this exhibit. If you have any questions, please feel free to contact me at the address shown below. Thank you for your support Sincerely, Joachim Seewald Cetecom ICT Services GmbH Email: [email protected]

Telematics Control Unit Model number: H913E Front/Top view Back view Antenna port

Sage Co.,Ltd. Bentendori Naka-ku 7F 4-59, Yok o ha m a Ci t y Kanagawa Pref 231-0007 1 Label Location FCC Label FCC Label

APPLICANT: Sage Co., Ldt. FCC ID: VRBH913E FCC IDENTIFICATION (NAMEPLATE) INFORMATION The FCC label shown is representative of the label that wi ll appear on the radio when in production. It will be placed on the outside of the equipment as shown in Exhibit X. Other information may also be included on this label. FCC ID: VRBH913E This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

APPLICANT: MOTOROLA INC. FCC ID: IHDT56FV2 Front View (Shields Removed) Rear View (Shields Removed) 1 EXHIBIT 9 APPLICANT: MOTOROLA INC. FCC ID: IHDT56FV2 Front View (With Shield) Rear View (With Shield) 2 EXHIBIT 9

Telematics Control Unit H913E Board Photographs 1.1 TOP View of the EUT 1: Telecommunication module (g24 E) 2: SIM socket 3: CAN (Car Area Network) connector, Power connector 4: Antenna connector 1 2 3 4 2 1.2 TOP View of Mother Board 1.3 Botom View of Mother Board

CETECOM Inc. 411 Dixon Landing Road Milpitas, CA 95035 Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Reviewing Engineer The Telematics Control Unit H913E from Sage Co., Ltd. is a mobile device with a built in GSM module. Due to the construction and the position of the antenna a distance under normal operating conditions of 20 cm or more is guaranteed. Additionally the user manual state: The installation of the device is performing by the manufacturer at the rear window of the car and ensures at least 20cm distance from the antenna to any person inside or outside of the car. The maximum output power of the Burst 1729 mW (32.38 dBm = 30.24 dBm ERP + 2.14 dB). R egarding MPE limits, GPUC environment limits maximum exposure to 1 mW/cm 2 . For 848.8 MHz maximum exposure limit is: f/1500= 848.8/1500= 0.57mW/cm 2 . The power density is: S = E 2 /3770=-13 H 2 = limit < 1 mW/cm 2 Where: S = Power density (mW/cm 2 ) E = electrical field strength (V/m) This formula converted using the EIRP at 20 cm. is: P out *G/4π*r 2 mW/cm 2 1729/4π*400 = 0.344 mW/cm 2 Further, the device uses the GSM protocol, which is a TDD format ratio of 1/8 in GSM mode and 4/8 in GPRS mode. Calculations are based on standard formula for calculating field strength at a distance and converting power density using free space impedance. If you should have any questions regarding this submission, please feel free to contact the undersigned. Yours truly, Ivaylo Tankov Project Engineer EMC/Radio CETECOM Inc.

Hermon Laboratories Ltd. P.O.Box 23, Binyamina 30500, Israel Tel. +972 4628 8001 Fax. +972 4628 8277 E-mail: [email protected] Page 1 of 138 Report ID: MOTRAD_FCC.17052_rev1.doc Date of Issue: May 2006 Electrical TEST REPORT ACCORDING TO: CFR47 FCC parts 22, 24 FOR: Motorola Israel Ltd. QuadBand GSM/GPRS/EGPRS module Model:G24EDGE This report is in conformity with ISO/ IEC 17025. The A2LA logo endorsement applies only to the test methods and the standards that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: MOTRAD_FCC.17052_rev1.doc Date of Issue: May 2006 Page 2 of 138 Table of contents 1 Applicant information..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details.................................................................................................................................................................... 3 5 Tests summary.............................................................................................................................................................. 4 6 EUT description............................................................................................................................................................. 5 6.1 General information....................................................................................................................................................... 5 6.2 Support and test equipment .......................................................................................................................................... 5 6.3 Operating frequencies ................................................................................................................................................... 5 6.4 Changes made in the EUT ............................................................................................................................................ 5 6.5 Transmitter characteristics ............................................................................................................................................ 6 7 Transmitter tests according to 47CFR part 22 requirements......................................................................................... 7 7.1 Peak output power ........................................................................................................................................................ 7 7.2 Occupied bandwidth test ............................................................................................................................................. 10 7.3 Spurious emissions at RF antenna connector test ...................................................................................................... 18 7.4 Field strength of spurious emissions ........................................................................................................................... 45 7.5 Frequency stability test................................................................................................................................................ 63 8 Transmitter tests according to 47CFR part 24 requirements....................................................................................... 65 8.1 Peak output power ...................................................................................................................................................... 65 8.2 Occupied bandwidth test ............................................................................................................................................. 68 8.3 Spurious emissions at RF antenna connector test ...................................................................................................... 76 8.4 Field strength of spurious emissions ......................................................................................................................... 105 8.5 Frequency stability test.............................................................................................................................................. 125 9 APPENDIX A Test equipment and ancillaries used for tests..................................................................................... 128 10 APPENDIX B Measurement uncertainties................................................................................................................. 129 11 APPENDIX C Test facility description ....................................................................................................................... 130 12 APPENDIX D Specification references ..................................................................................................................... 130 13 APPENDIX E Abbreviations and acronyms............................................................................................................... 131 14 APPENDIX F Test equipment correction factors ....................................................................................................... 132 Report ID: MOTRAD_FCC.17052_rev1.doc Date of Issue: May 2006 Page 3 of 138 1 Applicant information Client name: Motorola Israel Ltd. Address: 3 Kremenetski street, P.O.B. 25016, 67899 Tel Aviv, Israel Telephone: +972 3565 8888 Fax: +972 3565 9968 E-mail: [email protected] Contact name: Mr. Alfred Firouz 2 Equipment under test attr…

Text truncated - open the document above for the full version.

Hermon Laboratories Ltd. P.O.Box 23, Binyamina 30500, Israel Tel. +972 4628 8001 Fax. +972 4628 8277 E-mail: [email protected] Page 1 of 153 Report ID: MOTRAD_FCC.16719_rev1.doc Date of Issue: November 2005 Electrical TEST REPORT ACCORDING TO: FCC parts 22, 24 and part 15 subpart B FOR: Motorola Communications Israel Ltd. QuadBand GSM module 850/1900 MHz Model:G24 FCC ID:IHDT56FV1 This report is in conformity with ISO/ IEC 17025. The A2LA logo endorsement applies only to the test methods and the standards that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: MOTRAD_FCC.16719_rev1.doc Date of Issue: November 2005 Page 2 of 153 Table of contents 1 Applicant information..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details.................................................................................................................................................................... 3 5 Tests summary.............................................................................................................................................................. 4 6 EUT description............................................................................................................................................................. 5 6.1 General information....................................................................................................................................................... 5 6.2 Support and test equipment .......................................................................................................................................... 5 6.3 Operating frequencies ................................................................................................................................................... 5 6.4 Changes made in the EUT ............................................................................................................................................ 5 6.5 Transmitter characteristics ............................................................................................................................................ 6 7 Transmitter tests according to 47CFR part 22 requirements......................................................................................... 7 7.1 Peak output power ........................................................................................................................................................ 7 7.2 Occupied bandwidth test ............................................................................................................................................. 10 7.3 Spurious emissions at RF antenna connector test ...................................................................................................... 17 7.4 Field strength of spurious emissions ........................................................................................................................... 42 7.5 Frequency stability test................................................................................................................................................ 60 8 Transmitter tests according to 47CFR part 24 requirements....................................................................................... 63 8.1 Peak output power ...................................................................................................................................................... 63 8.2 Occupied bandwidth test ............................................................................................................................................. 66 8.3 Spurious emissions at RF antenna connector test ...................................................................................................... 73 8.4 Field strength of spurious emissions ......................................................................................................................... 101 8.5 Frequency stability test.............................................................................................................................................. 122 9 Unintentional radiation tests according to 47CFR part 15 subpart B requirements ................................................... 125 9.1 Conducted emissions ................................................................................................................................................ 125 9.2 Radiated emissions ................................................................................................................................................... 129 10 APPENDIX A Test equipment and ancillaries used for tests..................................................................................... 139 11 APPENDIX B Measurement uncertainties................................................................................................................. 141 12 APPENDIX C Test facility description ....................................................................................................................... 142 13 APPENDIX D Specification references ..................................................................................................................... 142 14 APPENDIX E Abbreviations and acronyms......................................................................…

Text truncated - open the document above for the full version.

Bluetooth Qualification Test Facility (BQTF) FCC listed A2LA accredited IC recognized # 3462B CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May V1.1 2003-03-01 The BLUETOOTH trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to CETECOM Inc. © Copyright by CETECOM FCC Test Report FCC Part 22, 24 for Sage Co., Ltd. Telemeter system for automobile with Quad-band module – Motorola G24 E Model Number: H913E FCC ID: VRBH913E IC-ID: NA TEST REPORT #:EMC_CET10_010_07503_FCC22-24 . DATE: November 01, 2007 Test Report #:EMC_CET10_010_07503_FCC22-24 . Date of Report: November 01, 2007 Page 2 of 55 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. Table of Contents 1 ASSESSMENT .....................................................................................................................................4 EMC & Radio.........................................................................................................................................4 EMC & Radio.........................................................................................................................................4 2 ADMINISTRATIVE DATA................................................................................................................5 2.1 IDENTIFICATION OF THE TESTING LABORATORY ISSUING THE SAR ASSESSMENT REPORT...............5 2.2 IDENTIFICATION OF THE CLIENT....................................................................................................5 2.3 IDENTIFICATION OF THE MANUFACTURER.....................................................................................5 3 EQUIPMENT UNDER TEST (EUT) .................................................................................................6 3.1 SPECIFICATION OF THE EQUIPMENT UNDER TEST..........................................................................6 3.2 IDENTIFICATION OF ACCESSORY EQUIPMENT................................................................................6 SUBJECT OF INVESTIGATION..............................................................................................................7 4 MEASUREMENTS..............................................................................................................................8 4.1 RF POWER OUTPUT........................................................................................................................8 4.1.1 FCC 2.1046 Measurements required: RF power output........................................................8 4.1.2 Limits: ....................................................................................................................................8 4.1.2.1 FCC 22.913 (a) Effective radiated power limits. ...............................................................8 4.1.2.2 FCC 24.232 (b)(c) Power limits. ........................................................................................8 4.1.3 Conducted Output Power Measurement procedure:..............................................................8 4.1.4 Results 850 MHz band (conducted): ......................................................................................9 4.1.5 Results 1900 MHz band (conducted): ....................................................................................9 4.1.6 Radiated Output Power measurement procedure: ...............................................................10 4.1.7 ERP Results 850 MHz band: ................................................................................................11 4.1.8 EIRP Results 1900 MHz band:.............................................................................................11 4.2 OCCUPIED BANDWIDTH/EMISSION BANDWIDTH.........................................................................12 4.2.1 FCC 2.1049 Measurements required: Occupied bandwidth................................................12 4.2.2 Occupied / emission bandwidth measurement procedure:...................................................12 4.2.3 Occupied / Emission bandwidth results 850 MHz band: .....................................................13 4.2.4 Occupied / Emission bandwidth results 1900 MHz band: ...................................................13 4.3 FREQUENCY STABILITY................................................................................................................14 4.3.1 Limit .....................................................................................................................................14 4.3.2 FREQUENCY STABILITY (GSM-850) ................................................................................15 4.4 SPURIOUS EMISSIONS CONDUCTED..............................................................................................17 4.4.1 FCC 2.1051 Measurements required: Spurious emissions at antenna terminals. ...............17 4.4.2 Limits: ..................................................................................................................................17 4.4.2.1 FCC 22.917 Emission limitations for cellular equipment. ..............................................17 4.4.2.2 FCC 24.238 Emission limitations for Broadband PCS equipment. ................................17 4.4.3 Conducted out of band emissions measurement procedure: ................................................18 4.4.4 Band Edge Results GSM-850 ...............................................................................................19 4.4.5 Conducted Spurious Results GSM-850 ................................................................................20 4.4.6 Band Edge Results PCS-1900 ............................................................…

Text truncated - open the document above for the full version.

PAGE 1 OF 3 Bluetooth Qualification Test Facility (BQTF) FCC listed# A2LA Certified IC recognized # 3462B CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM Test Setup Photos FCC Part 22, 24 / RSS 132,133 FOR: SAGE Co., Ltd MODEL #: H913E FCC ID: VRBH913E IC: NA Reference test report no.: EMC_CET10_010_07503_FCC22-24 PAGE 2 OF 3 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. 1 TEST SETUP PHOTOS RADIATED EMISSIONS - Front PAGE 3 OF 3 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. RADIATED EMISSIONS - Back RADIATED EMISSIONS - Side