W2ASW301RFINGERPRINT ACCESS CONTROLLER

© Copyright 2012, NITGEN&COMPANY Co., Ltd. All rights reserved. NITGEN&COMPANY Customer Service Center Tel: +82.2.513.2147 Fax: +82.2.513.2191 Email: [email protected] z Unauthorized reproduction of part or all of this manual’s content in any form is prohibited. z Product specifications may change without prior notice to improve functionality. z NITGEN & COMPANY and NITGEN logo are registered trademarks of NITGEN & COMPANY. z Other names and trademarks belong to respective companies. 3 Contents CHAPTER 1 GETTING STARTED ................................................................................... 4 PRODUCT INTRODUCTION ........................................................................................... 5 SYSTEM CONFIGURATION ........................................................................................... 6 PRODCUT DESCRIPTION .............................................................................................. 7 TOUCH SCREEN DISPLAY ............................................................................................ 8 CHAPTER 2 ADMINISTRATOR MENU ............................................................................ 9 ENTERMING ADMINISTRATOR MENU ......................................................................... 10 USER MANAGEMENT ................................................................................................ 17 AUTHENTICATION CONFIGURATION .......................................................................... 37 SYSTEM MANAGEMENT ............................................................................................ 48 NETWORK CONFIGARTION ....................................................................................... 65 USB MEMORY MANAGEMENT .................................................................................. 72 EXTERNAL IO CONNECTION ..................................................................................... 78 TERMINAL INITIALIZATION ......................................................................................... 84 CHAPTER 3 APPENDIX ............................................................................................. 89 TROUBLESHOOTING ................................................................................................. 90 SPECIFICATION ........................................................................................................ 92 Chapter 1 Getting Started Product Introduction System Configuration Product Description Touch Screen Display 5 Product Introduction The SW300/SW301 is general purpose Access controller using NITGEN’s core technologies – fingerprint authentication algorithm, optical sensor, embedded system design experiences, and application programs for PC. It introduces more friendly design and user interface through 4.3” touch screen TFT-LCD. And it provides various authentication methods – fignerrprint, RF card, ID & password, and combinations of them. Biometric technology Ergonomic Design User-friendly software System Configuration The SW300/SW301 can operation as network mode or stand-alone mode by configuration. In network mode, multiple terminals are connected to server PC through TCP/IP links and managed by administer. In stand-alone mode, single terminal operates and administrated without server connection. To use SW300/SW301 in network mode, a server and a management program (Access manager Professional) must be installed. Item Functions Server PC 1. ServerS/W : AccessManager Professional 2. Terminal management, communication, and log data collection 3. User profile and log DB 4. Authentication Client PC 1. Client S/W : RemoteManager 2. User registration and management 3. Checking terminal status and monitoring events terminal (SW300/SW301 ) 1. User registration, changing, deletion and checking 2. Consecutive registration of card-only users 3. Handling Warning / Alarm 4. Door control 5. Customizing users 6. Checking logs 7 Prodcut Description Touch Screen LCD Indicator LED Blue: Stand-by Green: Success Red: Fail Fingerprint window Card input area Touch Screen Display The follwiong symbos are displayed depending on the network connection status and mode Connected to server in network mode Not connected to server in network mode Stand-alone mode Network Connection Status Door Status Message from server Time Administration Menu Button Authentication Button Chapter 2 Administrator Menu Entering Administrator Menu User Management Authentication Configuration System Management Network Configuration USB Memory Management External IO Connection Terminal Initialization Enterming Administrator Menu Terminalsers are consists of general users and administrators. General users are only allowed to authentication operation while administrator can change terminal’s function by administrator menu. By touching administrator menu button, administrator authentication screen is displayed. 11 1. If no administrator is designated and only general users are registrated in network mode, all users are allowed to enter the administrator menu without authentication. 2. 1:N authentication is used, an administroator with a registered fingerpint can enter administrator menu by authentication of fingerprint without entering ID. After authenticating the administrator, administrator menu will be displayed. When delivered from factory, any user can enter the administrator menu without authentication because no user is registered. More than one user must be registered as administrator for security purposes. The administrator menu consists of 7 top-menus as shown below. Top Menu Sub Menu Funtion Lists User Management Registration, Changing, Deletion, List, and Seraching Card-Only Registration of card user Log Viewing and Searching Authentication Default Security Level, 1:N Authentication, 1:N Authentication Timeout T & A T&A Type, T&A Auth. Only Timezone Checking Timezone Camera Capture setting, Display ETC Log Saving Enble, User name display mod…

Text truncated - open the document above for the full version.

CPU (32Bit RISC) Samsung ARM11 Core S3C6410 667MHz Mobile SDRAM 128MB*2 NAND FLASH 256MB NOR FLASH 1MB Operation 1 33 MHz FP Data, Log Data, Flash Data Application OS Algorithm 32.768KHz 27MHz 12MHz FP Sensor(Auto On) CPU(MCLK 17MHz) Sensor(PCLK 8.5MHz) 4.3” TFT Touch Window Status LED Auth Success(Green) Auth Fail(Red) Sta n d - by( Bl ue) FP Image Capture Sensor Control Touch Coordinate LCD Control LED GPIO Control POE 12V/12W(AG9612-2BR) Regulator 5V, 3.3V, 2.8V, 2.5V, 1.8V, 1.3V, 1.2V Face Image Capture Camera Control l Camera 20MHz Battery(Optional) 2000mAh/7.4V Temper S/W Alarm GPIO Control OTG (48MHz) Audio Amp ( 24.576MHz ) Ethernet 25MHz Sound Control Speaker(8Ω/1W) USB Host 12MHz O/S Debug User/Log/Firmware Download USB Memory Stick Network TCP/IP(10/100) O/S Communication RF Module RS232 Transceiver*2 ZT3232LEEY RS232_1 3Pin Connector 125KHz RF Module. Antenna Wiegand TTL Wiegand In TTL Wiegand Out TTL RTC 3 2.7 65 MHz Time Control

KOREA TECHNOLOGY INSTITUTE CO., LTD. 51-19, Sanglim3-Riri, Docheok-Myeun, Gwangju-Shi, Gyeunggi-Do, Korea http://www.emc.re.kr E-mail: [email protected] Tel: 82-31-763-6709, Fax: 82-31-764-6709 Declaration Of Conformity FCC Registration Number 99058 Test Report No. KTI12EF11001 Test Site Korea Technology Institute Co. Ltd. Manufacture NITGEN&COMPANY Co., Ltd. Date of Test November 14, 2012 Contact Person Richard Kim / Manager Tel : +82-70-7405-2103 Fax : +82-2-513-3605 Product Type Access Controller Model Multiple Model SW301R SW300R FCC Rule Part(s) Part 15, Subpart B Classification Class B The device bearing the trade name and model specified above has been shown to comply with the applicable technical standard as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C.63.4-2003. I attest to the accuracy of data and all measurement reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualification of all persons taking them. Ph.D. Gyung Chan, Min/ President

KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 1 of 5 External photo (Front) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 2 of 5 External photo (Rear) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 3 of 5 External photo (Side) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 4 of 5 Adaptor photo (Rear) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 5 of 5 Adaptor photo (Rear)

KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 1 of 1 Label location FCC ID Label Location

KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 1 of 1 FCC ID Sample Label Label Drawing (SW301R)

KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 1 of 6 Internal photo 1 KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 2 of 6 Internal photo 2 (Front)) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 3 of 6 Internal photo 3 (Rear) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 4 of 6 Internal photo 4 (Front) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 5 of 6 Internal photo 5 (Rear) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 6 of 6 Internal photo 6 (Front)

Applicant: UNION COMMUNITY co.,Ltd. Model Name: V-RF32B 1. Operation Description 1) General Description The eProx MCM is supplied by mea ns of an electromagnetic field induced on the attached coil. The AC voltage is rectified in order to provide a DC internal s upply voltage. When the last bi t is sent, the chip will continue with the first bit until the power goes off. 2) Radio Architecture (1) Transmitter Architecture The circuit performs the two fun ctions of an RFID basestation, namely: transmission and reception. Transmission involves antenna driving and AM modulation of the RF field. The antenna drivers deliver a current into the external antenna to generate the magnetic field. Reception invo lves the AM demodulation of th e antenna signal modulation induced by the transponder. This is achieved by sensing the abs orption modulation applied by the tag (transponder). The antenna drivers supply the re ader basestation antenna with the appropriate energy. They deliver current at the resonant frequency which is typically 125 kHz. Current delivered by driv ers depends on Q of ex ternal resonant circ uit. It is strongly recommended that design of antenna circuit is done in a way tha t maximum peak current of 250 mA is never exceeded (see Typical Operating Conf iguration for antenna current calculation ). Another limiting factor for antenna current is Thermal Convection of package. Maximum peak current should be designed in a way that internal junction temperature does not exceed maximum junction temperat ure at maximum application ambi ent temperature. 100% modulati on (field stop) is done by switching OFF the drivers. The ANT drivers are protected agains t antenna DC short circuit to the power supplies. (2) Receiver Architecture The demodulation input signal fo r the reception block is the vo ltage sensed on the antenna. DEMOD_IN pin is also used as input to Reception chain. The signal level on the DEMOD_IN input must be lower than VDD-0.5V and higher than VSS+0.5V. The input level is adjusted by the use of an external capacitive divide r. Additional capacitance of divider must be compensated by a ccordingly smaller resonant cap acitor. The AM demodulation scheme is based on the "AM Synchronous Demodulation" techni que. The reception chain is com posed of sample and hold, DC offset cancellation, bandpass filter and comparator. D C voltage of signal on DEMOD_I N is set to AGND by internal resistor. The AM signal is sampled, the sampling is synchronised by a clock from VCO. Any DC component is removed from this signal by the CDEC capacitor.

KTI12EF11003 FCC ID: W2ASW301M Korea Technology Institute Co., Ltd. Page 1 of 1 Antenna Requirement 1 Loop Antenna

55 44 33 22 11 D D C C B B A A /RESETSCKMOSI MISO /RESET /RESET MISOMOSISCK RxD0 RxD0TxD0 TxD0 /RESET WG_D1 WG_D0 WG_OUT1 WG_OUT0 WG_OUT0WG_OUT1 WG_D0WG_D1 WG_D0WG_D1 VCC VCC VCC VCC VCCVCC VCC VCC VCC VCC VCC TitleSize Document Number Rev Date: Sheet of <Doc> <RevCode> <Title> :HID RFID Reader For Nitgen Custom 1 1 Monday, December 17, 2012 TitleSize Document Number Rev Date: Sheet of <Doc> <RevCode> <Title> :HID RFID Reader For Nitgen Custom 1 1 Monday, December 17, 2012 TitleSize Document Number Rev Date: Sheet of <Doc> <RevCode> <Title> :HID RFID Reader For Nitgen Custom 1 1 Monday, December 17, 2012 Program wiegand output KHD-A4C-05___-0B MCM(Nitgen사양) 2012/04/14 C100.1uFC100.1uF 12 D21N4148D21N4148 R3 100 R3 100 U3MAX3232/SOU3MAX3232/SO GND 15 VCC 16 R1IN 13 R2IN 8 T2IN 10 T1IN 11 C1+ 1 C1- 3 C2+ 4 C2- 5 R1OUT 12 R2OUT 9 T1OUT 14 T2OUT 7 V+ 2 V- 6 C2 20p C2 20p R10820R10820 R4 10K R4 10K U2MCM 4025U2MCM 4025 D6 19 C5 13 MCRL 1 DATA0 2 DATA1 3 CARD PRESENT 4 Red LED 5 Green LED 6 D1 7 D4 8 MDATA 9 AMP 10 Beeper 11 D3 12 B1 14 INPUT 15 TRANSMIT 16 D5 17 RECEIVE 18 ANT- 29 ANT+ 30 RED IN 25 HOLD IN 26 GND 28 B0 22 BEEPER IN 23 B2 21 B3 20 GREEN IN 24 VDD 27 C1210uF/16VC1210uF/16V C80.1uFC80.1uF 1 2 R910KR910K J1CON2(1.25mm)J1CON2(1.25mm) 12 C5 104 C5 104 R510KR510K C6 104 C6 104 C1 20p C1 20p R11KR11K Q2KTC3875SQ2KTC3875S B EC CN1 CON4P(1.25mm pitch) CN1 CON4P(1.25mm pitch) 1234 C90.1uFC90.1uF 1 2 CN2 CON4P(1.25mm pitch) CN2 CON4P(1.25mm pitch) 4321 C40.1uFC40.1uF 12 D31N4148D31N4148 R11 10 R11 10 D1LEDD1LED Y1 14.7456MHz Y1 14.7456MHz R8 10K R8 10K C3 2200p C3 2200p 1 2 R210KR210K C11 0.1uF C11 0.1uF 1 2 CN3 CON6P(2.54mm pitch) CN3 CON6P(2.54mm pitch) 123456 R7 10 R7 10 Q1KTC3875SQ1KTC3875S B EC C7 0.1uF C7 0.1uF 1 2 R1 100 R1 100 U1ATtiny2313(SOIC)U1ATtiny2313(SOIC) PA2(RESET) 1 VCC 20 PB0 12 PB1 13 PB2 14 PB3 15 PB4 16 PB5(MOSI) 17 PB6(MISO) 18 PB7(SCK) 19 (RXD)PD0 2 (TXD)PD1 3 (INT0)PD2 6 (INT1)PD3 7 PD4 8 PD5 9 PD6 11 PA1(XTAL2) 4 PA0(XTAL1) 5 R6820R6820

11 A A /RESETSCKMOSI MISO /RESET MOSISCK RxD0 RxD0TxD0 TxD0 WG_D1 WG_D0 WG_OUT1 WG_OUT0 WG_OUT0WG_OUT1 WG_D0WG_D1 WG_D0WG_D1 /RESET MISO /RESET VCC VCCVCC VCC VCC VCC VCC VCC VCC VCC VCC TitleSize Document Number Rev Date: Sheet of <Doc> <RevCode> <Title> :HID RFID Reader For Nitgen Custom 1 1 Friday, November 16, 2012 TitleSize Document Number Rev Date: Sheet of <Doc> <RevCode> <Title> :HID RFID Reader For Nitgen Custom 1 1 Friday, November 16, 2012 TitleSize Document Number Rev Date: Sheet of <Doc> <RevCode> <Title> :HID RFID Reader For Nitgen Custom 1 1 Friday, November 16, 2012 Program wiegand output C6 104 C6 104 C11 0.1uF C11 0.1uF 1 2 R6820R6820 C1210uF/16VC1210uF/16V R10820R10820 R11KR11K D31N4148D31N4148 R1210KR1210K Q1KTC3875SQ1KTC3875S B EC R7 10 R7 10 R510KR510K C3 2400p C3 2400p 1 2 Q2KTC3875SQ2KTC3875S B EC CN2 CON4P(1.25mm pitch) CN2 CON4P(1.25mm pitch) 4321 J1CON2(1.25mm)J1CON2(1.25mm) 12 R8 10K R8 10K R3 100R3 100 U2 4025 U2 4025 D6 19 C5 13 MCRL 1 DATA0 2 DATA1 3 CARD PRESENT 4 Red LED 5 Green LED 6 D1 7 D4 8 MDATA 9 AMP 10 Beeper 11 D3 12 B1 14 INPUT 15 TRANSMIT 16 D5 17 RECEIVE 18 ANT- 29 ANT+ 30 RED IN 25 HOLD IN 26 GND 28 B0 22 BEEPER IN 23 B2 21 B3 20 GREEN IN 24 VDD 27 D21N4148D21N4148 C7 0.1uF C7 0.1uF 1 2 C40.1uFC40.1uF 12 C90.1uFC90.1uF 1 2 R4 10K R4 10K C80.1uFC80.1uF 1 2 CN3 CON6P(2.54mm pitch) CN3 CON6P(2.54mm pitch) 123456 C100.1uFC100.1uF 12 C2 20p C2 20p C5 104 C5 104 Y1 14.7456MHz Y1 14.7456MHz U1ATtiny2313(SOIC)U1ATtiny2313(SOIC) PA2(RESET) 1 VCC 20 PB0 12 PB1 13 PB2 14 PB3 15 PB4 16 PB5(MOSI) 17 PB6(MISO) 18 PB7(SCK) 19 (RXD)PD0 2 (TXD)PD1 3 (INT0)PD2 6 (INT1)PD3 7 PD4 8 PD5 9 PD6 11 PA1(XTAL2) 4 PA0(XTAL1) 5 R910KR910K U3MAX3232/SOU3MAX3232/SO GND 15 VCC 16 R1IN 13 R2IN 8 T2IN 10 T1IN 11 C1+ 1 C1- 3 C2+ 4 C2- 5 R1OUT 12 R2OUT 9 T1OUT 14 T2OUT 7 V+ 2 V- 6 C1 20p C1 20p D1LEDD1LED CN1 CON4P(1.25mm pitch) CN1 CON4P(1.25mm pitch) 1234 R2 100 R2 100 R11 10 R11 10

KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 1 of 26 Test Report Test Report No.: KTI12EF11004 Registration No.: 99058 Applicant: NITGEN&COMPANY Co., Ltd. Applicant Address: Pax Tower B/D, 12FL., 231-13, Nonhyeon-dong, Gangnam-gu, Seoul, Korea (135-010) Product: Access Controller FCC ID: W2ASW301R Model No. SW301R,SW300R Receipt No.: 12-1104 Date of receipt:November 14, 2012 Date of Issue: November 30, 2012 Testing location Korea Technology Institute Co., Ltd. 51-19, Sanglim3-Ri, Docheok-Myeun, Gwangju-Shi, Gyeungki-Do, Korea Test Standards: FCC/ANSI. C63.4: 2003 Rule Parts: FCC Part 15, Class B Equipment Class: Digital device Test Result: The above-mentioned product has been tested with compliance. Tested by: T.J. Kim / Engineer Approved by: G. C. Min /President Signature Date November 30, 2012 Signature Date November 30, 2012 Other Aspects: Abbreviations: * OK, Pass=passed * Fail=failed * N/A=not applicable ☞ - This test report is not permitted to copy partly without our permission. - This test result is dependent on only equipment to be used. - This test result is based on a single evaluation of one sample of the above mentioned. - This test report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S Government. - We certify this test report has been based on the measurement standards that is traceable to the national or international standards. KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 2 of 26 >> Contents << Contents 2 List of Tables 2 List of Figures 2 List of Photographs 2 1. General 4 2. Test Site 4 2.1 Location 4 2.2 List of Test and Measurement Instruments 4 2.3 Test Date 5 2.4 Test Environment 5 3. Description of the tested samples 6 3.1 Rating and Physical characteristics 6 3.2 Submitted documents 6 4. Measurement conditions 7 4.1 Modes of operation 7 4.2 Additional Equipment 7 4.3 Uncertainty 7 4.4 Test Setup 8 5. TEST AND MEASUREMENTS 9 5.1 Antenna Requirement 9 5.1.1 Regulation 9 5.1.2 Results 9 5.2 Emission Test 10 5.2.1 Conducted Emissions 10 5.2.2 Radiated Emissions 17 5.2.2.1 Regulation 17 5.2.2.2 Measurement Procedure 17 5.2.2.3 Calculation of the field strength limits below 30 MHz 18 5.2.2.4 Test Results 19 5.2.2.5 Calculation of the field strength limits above 30 MHz 23 5.2.2.6 Test Results 23 KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 3 of 26 ≫≫ Contents ≪≪ 5. 5.3 Occupied bandwidth 20 5.3.1 Measurement Procedure 20 5.3.2 Test Results 20 6. Photograph of the Test Set-Up 22 >> List of Tables Table 1 List of test and measurement equipment 5 Table 2 Test Data. Conducted Emissions 13,16 Table 3 Test Data, Fundamental Frequency (Ver / Hor) 19,21 Table 4 Test Data, Radiated Emission below 30 MHz 19,21 Table 5 Test Data, Radiated Emission above 30 MHz 23,24 >> List of Figures Figure 1 Test Setup_Adaptor Mode 8 Figure 2 Test Setup_PoE Mode 8 Figure 3 Spectral Diagram, LINE-PE 11,14 Figure 4 Spectral Diagram, NEUTRAL-PE 12,15 Figure 5 Radiated spurious emissions below 30 MHz 20,22 Figure 6 Occupied Bandwidth 25,26 >> List of Photographs Photograph 1 Setup for conducted Emissions 27 Photograph 2 Setup for radiated Emissions 28 KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 4 of 26 1. General This equipment has been shown to be capable of compliance with the applicable technical standards and was tested in accordance with the measurement procedures as indicated in this report. We attest to the accuracy of data. Korea Technology Institute Co., Ltd. performed all measurements reported herein. And were made under Chief Engineer’s supervisor. We assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. 2. Test Site Korea Technology Institute Co., Ltd. Location 51-19, Sanglim3-Ri, Docheok-Myeun, Gwangju-Shi, Gyeungki-Do, Korea The Test Site is in compliance with ANSI C63.4/2003 for measurement of radio Interference. KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 5 of 26 List of Test and Measurement Instruments Table 1: List of Test and Measurement Equipment - Conducted Emissions Kind of Equipment Type S/N Calibrated until Field Strength Meter ESIB40 100093 05.2013 LISN KNW407 8-1157-2 03.2013 LISN EM-7823 115019 03.2013 Conducted Cable N/A N/A 11.2013 - Radiated Emissions Kind of Equipment Type S/N Calibrated until Field Strength Meter ESIB40 100093 05.2013 Loop Antenna 6502 3434 02.2013 Biconic Logarithmic Periodic Antenna VULB9163 9163-281 10.2014 Horn Antenna 3115 6443 10.2014 Open Site Cable N/A N/A 11.2009 Antenna Master DETT-03 N/A N / A Antenna & Turntable controller DETT-04 91X519 N / A Test Date Date of Application: Noverber 14, 2012 Date of Test: Noverber 14, 2012 Test Environment Indoor: 22°C/38%/1000mbar Outdoor: 4°C/39%/1000mbar KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 6 of 26 3. Description of the tested samples The EUT is Access Controller. 3.1 Rating and Physical Characteristics Item Description LCD 4.3” Touch Screen TFT-LCD High Color(16Bit), 480(H) x 272(W) CPU 667MHz 32Bit RISC Memory 256MB RAM, 256MB Nand Flash RF Characteristic 125KHz, 500uV/m @ Less than 3m Sensor NITGEN OPP06 Optic sensor 500DPI(LFD, Auto-On) Authenticaition Speed 1:1 Verificaitoin: less than 0.5 second 1:N Identification: less than 1 second in 4000 templats FAR/FRR 0.001% /0.1% Capacity 100,000 templates or 100,000 users(PW, RF) Communication TCP/IP, WIFI, Wiegand Dimension 167.4(W) x 146.5(L) x 67(H) mm Adaptor Power Input : AC 100V ~ 240V, 50/60 Hz Output: DC 12V, 3A Door Connection Upto two doors (DeadBolt, Electro Magnetic- lock, Elecric Strike, Auto door Fire Alarm) Temperature/ Humidity -20 ~ 60°C etc Voice announcement, USB Port Warning/Alarm 3.2 Submitted Documents • User’s Guide • Block Diagram KTI12EF11004 FCC ID:W2ASW301R Korea Technology Institute Co., Ltd. Page 7 of 26 4. Measurement Conditions Testing …

Text truncated - open the document above for the full version.

KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 1 of 3 6. Photograph of the Test Set-Up Photograph 1 : Setup for radiated Emissions (below 30 MHz) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 2 of 3 Photograph 2 : Setup for radiated Emissions (above 30 MHz) KTI12EF11004 FCC ID: W2ASW301R Korea Technology Institute Co., Ltd. Page 3 of 3 Photograph 3 : Setup for Conducted Emissions