WAGNP311DNAIL PRINTER

1 AIS CONFIDENTIAL JOLIMARK NAIL PRINTER INSTRUCTION MANUAL NP311D 2 AIS CONFIDENTIAL Contents Foreword 1.1 Warnings Installation guide 2.1 Unpacking 2.2 Package contents 2.3 Product placement and environment 2.4 Product Movement Product settings 3.1 Product Introduction 3.2 Power On 3.3 Connect to WIFI 3.4 Nail printer APP Introduction 3.5 Installation and replacement of ink cartridge 3.6 Ink cartridge testing and maintenance 3.7 Camera calibration 3.8 Printing position calibration 3.9 Start a printing job Gel description 4.1 Gel type 4.2 gel description 4.3 Gluing process Specifications 5.1 Product specification 5.2 Ink cartridge specification 5.3Gel specification Indicator instructions and firmware upgrade 6.1 Indicator instructions 6.2 Firmware upgrade Troubleshooting 7.1 Troubleshooting 3 AIS CONFIDENTIAL Customer support 8.1 Customer Support Product safety instructions 9.1 Product Safety Instructions Certificate 10.1 QC Certificate 4 AIS CONFIDENTIAL FOREWORD This manual mainly serves as a guide to provide basic operating procedures and precautions for the users when using the product to avoid problems such as product circuit abnormality, electric shock, fire hazard, operator injury and damage caused by improper use of the product. Symbol Descript ion Warning: When this symbol appears in the manual, it implies that such behavior or condition may cause the product to encounter circuit abnormalities, electric shock, fire hazard, injury to the operator, or damage to the product. Caution: When this symbol appears in the manual, it implies that such behavior or condition may damage the product or cause injury to the operator. Table 1-1 Describe the definitions of the two symbols in this manual 1.1 Warnings 1. Please read this instruction manual carefully. 2. Never put the ink cartridge or power adapter into water or any liquid. 3. The metal contacts on ink cartridge must be kept dry and avoid touching the surface of the chip. 4. Do not touch the power cord or power plug directly with a wet hand. 5. This product must be placed away from extremely cold and hot sources and away fro m direct sunlight. 6. The ink cartridge will mo ve rapidly during the print process of the product; user is required to physically stay out of the print area to avoid injuries during printing. 7. When the power adapter, power cord or power plug is damaged, please do not use this product and contact customer service for repair. 8. Please clean the drip tray daily. Any damage to the product due to failure in cleaning the drip tray properly may affect the user’s right in the product warranty. 9. Please keep the accessories (i.e., necklace and bracelet) and hair of user away from this product to avoid any personal injury. 10. If any emergency occurs, turn off the power and unplug the power cord. 11. Please do not open the back cover of this product. This operation is very dangerous and will affect the warranty of this product. 12. During the use of the product, please be careful to avoid the hand being pinched, pressed, or bumped; if the above problem occurs, please turn off the power immediately. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5 AIS CONFIDENTIAL Installation Guide Thank you for purchasing the Jolimark Nail Printer (the Product), please follow the instructions below to install and use this product. 2.1 Unpacking 1. Open the packaging box 2. Remove the packaging (cushioning) materials 3. Take out the product 2.2 Package contents 1. A Nail Printer 2. A set of power adapter and power cord 3. An accessory box (including) : - 8 bottles of nail gel - One piece of Ink cartridge - One piece if nail holder 2.3 Product placement and environment 1. Please place the product on a solid plat form in a well-ventilated room, and keep the product away from direct sunlight. 2. Please place the product on a well-leveled surface to avoid ink leakage. It is recommended to place the product in an environment with temperature of 15°C ~ 30°C. 2.4 Product Movement If it is required to move the product for a long distance under bumpy condition, please put the product back into the package box and use the packaging (cushioning) materials to pack the product tightly to avoid damage to the product while moving. 1. Before moving. turn off power, unplug the power adapter and all power cords, remove the ink cartridge. 2. Do not tilt the product, place it sideways, or place it upside down during the movement. 3. If you still keep the packaging material, please put the product back into the package box and use the packaging (cushioning) materials to pack the product tightly to avoid damage to the product while moving. 4. If you have any questions, please contact our customer service staff. Product setting 3.1 Product introduction 6 AIS CONFIDENTIAL Figure 3.1 Parts of the product 3.2 Power On To use this product, first insert the round plug of the power adapter into the DC power socket of the product and then plug in the other end of the power adapter into the AC wall socket (110V~240V). Press the power switch to turn on the power of the product. 3.3 Connect to Wi-Fi 1. Press the power switch and wait for the Android tablet to boot. 2. Touch with your finger and slide down from the top of the screen to the setting screen. 3. Select WLAN option (in red circle). 4. Press the specified WLAN name and enter the password. 5. WIFI connection is completed. 2. Press the power switch 1. The power adapter round plug is inserted into the DC power socket of this product. 7 AIS CONFIDENTIAL Press the power switch and wait for the Android tablet to boot. Touch with your finger and slide down from the top of the screen to setting screen. Select WLAN option (in red circle). Press the specified WLAN name. Press the specified W…

Text truncated - open the document above for the full version.

FCC, Request for non-disclosure Date: 19-Oct-10 RF_501, Issue 7 Page 1 of 1 Company Name: KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address: 18 Kong Yue Industrial Park, Jinguzhou Zone Xinhui District City: Jiangmen City Country: China To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: WAGNP311D Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: (notes 2, 3, 4, 5). If no date is given, 45 days from grant date will be used. Date: Dec. 25, 2019 Name and signature of applicant: HONG ZHANG Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Report No： 1930412R-RFUSP73V00 Page: 155 of 193 Attachment 2  EUT External Photograph (1) EUT Photo (2) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 156 of 193 (3) EUT Photo (4) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 157 of 193 (5) EUT Photo (6) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 158 of 193 (7) EUT Photo (8) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 159 of 193 (9) EUT Photo (10) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 160 of 193 (11) EUT Photo

Label Location The bottom of the EUT

Report No： 1930412R-RFUSP73V00 Page: 161 of 193 Attachment 3  EUT Internal Photograph (1) EUT Photo (2) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 162 of 193 (3) EUT Photo (Antenna) (4) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 163 of 193 (5) EUT Photo (6) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 164 of 193 (7) EUT Photo (8) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 165 of 193 (9) EUT Photo (10) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 166 of 193 (11) EUT Photo (12) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 167 of 193 (13) EUT Photo (14) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 168 of 193 (15) EUT Photo (16) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 169 of 193 (17) EUT Photo (18) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 170 of 193 (19) EUT Photo (20) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 171 of 193 (21) EUT Photo (22) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 172 of 193 (23) EUT Photo (24) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 173 of 193 (25) EUT Photo (26) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 174 of 193 (27) EUT Photo (28) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 175 of 193 (29) EUT Photo (30) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 176 of 193 (31) EUT Photo (32) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 177 of 193 (33) EUT Photo (34) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 178 of 193 (35) EUT Photo (36) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 179 of 193 (37) EUT Photo (38) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 180 of 193 (39) EUT Photo (40) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 181 of 193 (41) EUT Photo (42) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 182 of 193 (43) EUT Photo (44) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 183 of 193 (45) EUT Photo (46) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 184 of 193 (47) EUT Photo (48) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 185 of 193 (49) EUT Photo (50) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 186 of 193 (51) EUT Photo (52) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 187 of 193 (53) EUT Photo (54) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 188 of 193 (55) EUT Photo (56) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 189 of 193 (57) EUT Photo (58) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 190 of 193 (59) EUT Photo (60) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 191 of 193 (61) EUT Photo (62) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 192 of 193 (63) EUT Photo (64) EUT Photo Report No： 1930412R-RFUSP73V00 Page: 193 of 193 (65) EUT Photo

Report No. 1930412R-RFUSP02V00 Page: 1 of 8 RF Exposure Evaluation declaration Product Name ：NAIL PRINTER Trade Name ：Jolimark Model No. ：NP311D FCC ID. ：WAGNP311D Applicant : KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address : 18 Kongyue Road, Jinguzhou Zone, Xinhui District, Jiangmen City, Guangdong Province, China Date of Receipt : Mar. 26, 2019 Date of Declaration : Jan. 10, 2020 Report No. : 1930412R-RFUSP02V00 Report Version : V1.0 The declaration results relate only to the samples calculated. The declaration shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd.. Report No. 1930412R-RFUSP02V00 Page: 2 of 8 RF Exposure Evaluation Declaration Issued Date : Jan. 10, 2020 Report No. : 1930412R-RFUSP02V00 Product Name : NAIL PRINTER Applicant : KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address : 18 Kongyue Road, Jinguzhou Zone, Xinhui District, Jiangmen City, Guangdong Province, China Manufacturer : KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Model No. : NP311D FCC ID : WAGNP311D Trade Name : Jolimark Applicable Standard : FCC 47 CFR Part 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. Test Lab : Hsin Chu Laboratory Address ： No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Tested By : ( Elwin Lin / Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No. 1930412R-RFUSP02V00 Page: 3 of 8 Revision History Report No. Version Description Issued Date 1930412R-RFUSP02V00V1.0 Initial issue of report Jan. 10, 2020 Report No. 1930412R-RFUSP02V00 Page: 4 of 8 1. General Information 1.1. Test Facility Ambient conditions in the laboratory: Items Test Item Required (IEC 68-1) Actual Test Site Temperature (°C) FCC 2.091 Peak Power Output 15 - 35 20 3 Humidity (%RH) 25 - 75 50 Note: Test site information refers to Laboratory Information. USA : FCC Registration Number: TW3024 The related certificate for our laboratories about the test site and management system can be downloaded from DEKRA Testing and Certification Co., Ltd. Web Site: http://www.dekra.com.tw/english/about/certificates.aspx?bval=5 The address and introduction of DEKRA Testing and Certification Co., Ltd. laboratories can be founded in our Web site : http://www.dekra.com.tw/index_en.aspx If you have any comments, Please don’t hesitate to contact us. Our test sites as below: 1 No. 75-2, 3rd Lin, WangYe Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan (R.O.C.) TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected] 2 No.372, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 31061, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 E-Mail : [email protected] 3 No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 31061, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 E-Mail : [email protected] Report No. 1930412R-RFUSP02V00 Page: 5 of 8 1.2. List of Test Equipment Peak Power Output / SR10-H Instrument Manufacturer Model No. Serial No. Cal. Date Next Cal. Date High Speed Peak Power Meter Dual Input Anritsu ML2496A 1602004 2018/12/17 2019/12/16 Pulse Power Sensor Anritsu MA2411B 1531043 2018/12/17 2019/12/16 Pulse Power Sensor Anritsu MA2411B 1531044 2018/12/17 2019/12/16 Power Meter Keysight 8990B MY510002482018/06/07 2019/06/06 Power Sensor Keysight N1923A MY572400052018/06/07 2019/06/06 Note: All equipment upon which need to calibrated are with calibration period of 1 year. 1.3. Uncertainty Test item Uncertainty Peak Power Output ± 2.26 dB Determining compliance shall be based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Report No. 1930412R-RFUSP02V00 Page: 6 of 8 2. RF Exposure Evaluation 2.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 2.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. Report No. 1930412R-RFUSP02V00 Page: 7 of 8 2.3. Test Result of RF Exposure Evaluation Product NAIL PRINTER Test Mode Transmit Test Condition RF Exposure Evaluation Antenna Gain Antenna Gain: The maximum Gain is 2 dBi or 1.58 dBi in linear scale. Output Power into Antenna & RF Exposure Evaluation Distance: IEEE 802.11b (ANT 0) WLAN Function Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2412 126.474 0.040 6 2437 113.240 0.036 11 2462 91.622 0.029 IEEE 802.11g (ANT 0) WLAN Function Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2412 152.055 0.048 6 2437 174.181 0.055 11 2462 156.315 0.049 IEEE 802.11n (20MHz) (ANT 0) WLAN Function Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2412 143.549 0.045 6 2437 172.187 0.…

Text truncated - open the document above for the full version.

Report No：1930412R-RFUSP73V00-A Page: 1 of 92 FCC Test Report Product Name ：NAIL PRINTER Trade Name ：Jolimark Model No. ：NP311D FCC ID. ：WAGNP311D Applicant ：KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address ：18 Kongyue Road, Jinguzhou Zone, Xinhui District, Jiangmen City, Guangdong Province, China Date of Receipt：Mar. 26, 2019 Issued Date ：Jan. 10, 2020 Report No. ：1930412R-RFUSP73V00-A Report Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd. Report No：1930412R-RFUSP73V00-A Page: 2 of 92 Test Report Certification Issued Date : Jan. 10, 2020 Report No. : 1930412R-RFUSP73V00-A Product Name : NAIL PRINTER Applicant : KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address : 18 Kongyue Road, Jinguzhou Zone, Xinhui District, Jiangmen City, Guangdong Province, China Manufacturer : KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Trade Name : Jolimark Model No. : NP311D FCC ID. : WAGNP311D EUT Voltage : AC 100~240V, 50-60Hz Testing Voltage : AC 120V/60Hz Applicable Standard : FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2017 ANSI C63.10: 2013 Laboratory Name : Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Documented By : ( Demi Chang / Senior Engineering Adm. Specialist ) Tested By : ( Elwin Lin / Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No：1930412R-RFUSP73V00-A Page: 3 of 92 Revision History Report No. Version Description Issued Date 1930412R-RFUSP73V00-A V1.0 Initial issue of report Jan. 10, 2020 Report No：1930412R-RFUSP73V00-A Page: 4 of 92 TABLE OF CONTENTS Description Page 1. General Information .................................................................................................................. 6 1.1. EUT Description ......................................................................................................... 6 1.2. Test Mode ................................................................................................................... 7 1.3. Tested System Details ................................................................................................ 8 1.4. Configuration of tested System .................................................................................. 8 1.5. EUT Exercise Software .............................................................................................. 8 1.6. Test Facility ................................................................................................................. 9 1.7. List of Test Equipment .............................................................................................. 10 1.8. Duty cycle ................................................................................................................. 12 1.9. Uncertainty ............................................................................................................... 12 2. Conducted Emission .............................................................................................................. 14 2.1. Test Setup................................................................................................................. 14 2.2. Limits ........................................................................................................................ 14 2.3. Test Procedure ......................................................................................................... 15 2.4. Test Specification ...................................................................................................... 15 2.5. Test Result ................................................................................................................ 16 3. Maximum peak conducted output power ................................................................................ 18 3.1. Test Setup................................................................................................................. 18 3.2. Test procedures ........................................................................................................ 18 3.3. Limits ........................................................................................................................ 18 3.4. Test Specification ...................................................................................................... 18 3.5. Test Result ................................................................................................................ 19 4. Radiated Emission ................................................................................................................. 20 4.1. Test Setup................................................................................................................. 20 4.2. Limits ........................................................................................................................ 21 4.3. Test Procedure ......................................................................................................... 22 4.4. Test Specification ...................................................................................................... 22 4.5. Test Result ................................................................................................................ 23 5. RF antenna conducted test .................................................................................................... 3 1 5.1. Test Setup................................................................................................................. 31 5.2. Limits ........................................................................................................................ 31 5.3. Test Procedure .......................................................................................…

Text truncated - open the document above for the full version.

Report No： 1930412R-RFUSP73V00 Page: 1 of 193 FCC Test Report Product Name：NAIL PRINTER Trade Name ：Jolimark Model No. ：NP311D FCC ID. ：WAGNP311D Applicant ： KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address ： 18 Kongyue Road, Jinguzhou Zone, Xinhui District, Jiangmen City, Guangdong Province, China Date of Receipt：Mar. 26, 2019 Issued Date ：Jan. 10, 2020 Report No. ：1930412R-RFUSP73V00 Report Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd.. Report No： 1930412R-RFUSP73V00 Page: 2 of 193 Test Report Certification Issued Date : Jan. 10, 2020 Report No. : 1930412R-RFUSP73V00 Product Name ： NAIL PRINTER Applicant ： KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Address ： 18 Kongyue Road, Jinguzhou Zone, Xinhui District, Jiangmen City, Guangdong Province, China Manufacturer ： KONG YUE ELECTRONICS & INFORMATION INDUSTRY LTD. Model No. ： NP311D Trade Name ： Jolimark FCC ID. ： WAGNP311D EUT Test Voltage ： AC 100~240V, 50-60Hz Testing Voltage ： AC 120V/60Hz Applicable Standard： FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2017 ANSI C63.10: 2013 KDB 558074 D01 V05r02 / KDB 662911 D01 V02r01 Laboratory Name ： Hsin Chu Laboratory Address ： No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result ： Complied Documented By : ( Demi Chang / Senior Engineering Adm. Specialist ) Tested By : ( Elwin Lin / Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No： 1930412R-RFUSP73V00 Page: 3 of 193 Revision History Report No. Version Description Issued Date 1930412R-RFUSP73V00 V1.0 Initial issue of report Jan. 10, 2020 Report No： 1930412R-RFUSP73V00 Page: 4 of 193 TABLE OF CONTENTS Description Page 1. General Information ........................................................................................................ 6 1.1. EUT Description ............................................................................................................. 6 1.2. Test Mode ....................................................................................................................... 9 1.3. Tested System Details .................................................................................................. 10 1.4. Configuration of tested System .................................................................................... 10 1.5. EUT Exercise Software ................................................................................................ 10 1.6. Test Facility ................................................................................................................... 11 1.7. List of Test Equipment .................................................................................................. 12 1.8. Duty cycle ..................................................................................................................... 15 1.9. Uncertainty ................................................................................................................... 18 2. Conducted Emission .................................................................................................... 19 2.1. Test Setup .................................................................................................................... 19 2.2. Limits ............................................................................................................................ 19 2.3. Test Procedure ............................................................................................................. 20 2.4. Test Specification .......................................................................................................... 20 2.5. Test Result .................................................................................................................... 21 3. Maximum peak conducted output power ...................................................................... 23 3.1. Test Setup .................................................................................................................... 23 3.2. Test procedures ............................................................................................................ 23 3.3. Limits ............................................................................................................................ 23 3.4. Test Specification .......................................................................................................... 23 3.5. Test Result .................................................................................................................... 24 4. Radiated Emission ....................................................................................................... 25 4.1. Test Setup .................................................................................................................... 25 4.2. Limits ............................................................................................................................ 25 4.3. Test Procedure ............................................................................................................. 26 4.4. Test Specification .......................................................................................................... 26 4.5. Test Result .................................................................................................................... 27 5. RF antenna conducted test .......................................................................................... 59 5.1. Test Setup .................................................................................................................... 59 5.2. Limits ............................................................................................................................ 59 5.3. Test Pr…

Text truncated - open the document above for the full version.

Report No：1930412R-RFUSP73V00-A Page: 51 of 92 Attachment 1  Test Setup Photograph <Conducted Emission> Test Mode ： Mode 1: Transmit Description： Front View of Conducted Emission Test Setup Description： Back View of Conducted Emission Test Setup Report No：1930412R-RFUSP73V00-A Page: 52 of 92 < Radiated Emission > Test Mode ： Mode 1: Transmit Description： Front View of Radiated Emission Test Setup (Bilog) Description： Back View of Radiated Emission Test Setup (Bilog) Report No：1930412R-RFUSP73V00-A Page: 53 of 92 Test Mode ： Mode 1: Transmit Description： Front View of Radiated Emission Test Setup (Horn) Description： Back View of Radiated Emission Test Setup (Horn)

Report No： 19304…

Text truncated - open the document above for the full version.