WBKMBSC08S005RUMmBSC-C RUM

Document Name: mBSC0800S-005-RUCM11 Revision: 001.01A Effective Date: 4/15/2013 USER MANUAL mBSC0800S-005-RUCM11 Medium-Power Coverage Solution 6185 Phyllis Drive Cypress, CA 90630 USA PH: 714.230.8333 Visit our Website at www.BTIwireless.com mBSC0800S-005-RUCM11 BTI Wireless 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.btiwireless.com mBSC0800S-005-RUCM11 Copyright © 2015 BTI Wireless All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from BTI Wireless. All copyright, confidential information, patents, design rights and all other intellectual property rights of whatsoever nature contained herein are and shall remain the sole and exclusive property of BTI Wireless. The information furnished herein is believed to be accurate and reliable. However, no responsibility is assumed by BTI Wireless for its use, or for any infringements of patents or other rights of third parties resulting from its use. The BTI Wireless name and BTI Wireless logo are trademarks or registered trademarks of BTI Wireless All other trademarks are the property of their respective owners mBSC0800S-005-RUCM11 ©1999-2013 Bravo Tech Inc. Document History Paper copies are valid only on the day they are printed. Contact the author if you are in any doubt about the accuracy of this document. Revision History Revision Number Revision Date Summary of Changes 001.00A 5/28/2013 Initial Release for NA GENERAL SAFETY PRECAUTIONS Warning: Wet conditions increase the potential for receiving an electrical shock when installing or using electrically-powered equipment. To prevent electrical shock, never install or use electrical equipment in a wet location or during a lighting storm. Warning : This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. Improper installation and operation of this equipment outside of the recommended installation procedures, and operation beyond the designed operating specifications, and/or not in compliance with regulatory requirements, will revoke any warranty and may:  Prevent the equipment from performing properly  Violate regulatory RF emissions requirements  Require removal of the equipment from service. mBSC0800S-005-RUCM11 ©1999-2013 Bravo Tech Inc. TABLE OF CONTENTS 1 INTRODUCTION 1 1.1 SYSTEM SOLUTION BLOCK DIAGRAM 1 1.1.1 Host Unit 1 1.1.2 Remote Node 2 2 SAFETY 3 3 SYSTEM OVERVIEW AND UNIT DESCRIPTION 5 3.1 SYSTEM OVERVIEW 5 3.1.1 Interface with BTS 6 3.1.2 Interface with Cellular Phones 6 3.1.3 Fiber Optic Transport 6 3.1.4 Powering 6 3.1.5 Cooling 6 3.1.6 Fault Detection and Alarm Reporting 6 3.2 HOST UNIT DESCRIPTION 7 3.2.1 Host Unit Components 7 3.2.2 Mounting 10 3.2.3 Fault Detection and Alarm Reporting 10 3.2.4 RF Signal Connections 10 3.2.5 Optical Connections 10 3.2.6 Powering 11 3.2.7 Host Unit Interface 11 3.3 REMOTE NODE DESCRIPTION 13 3.3.1 BCM Enclosure 13 3.3.2 Single-band RUM Enclosure 15 3.3.3 RTM 19 3.3.4 RPM 23 4 SYSTEM INSTALLATION 26 4.1 UNPACKING AND INSPECTION 26 4.2 INSTALLATION PREPARATION 26 4.2.1 Required Tools 26 4.2.2 Installation Location 26 4.2.3 Anti-corrosion and Shock-protection 27 4.2.4 Lighting, Ventilation and Fire Protection 27 4.2.5 Power Requirements 27 mBSC0800S-005-RUCM11 ©1999-2013 Bravo Tech Inc. 4.2.6 Lightning Protecting and Grounding 27 4.3 HOST UNIT INSTALLATION 27 4.3.1 Rack Mounting 27 4.3.2 Cable Connections 29 4.4 REMOTE NODE INSTALLATION 33 4.4.1 Cable Connections 34 4.5 INSTALLATION FINAL INSPECTION 38 4.5.1 Host Unit Connection Overview 39 4.5.2 Remote Node Connection Overview 40 4.5.3 mBSC-C Inspection Checklist 41 4.5.4 Cabling Inspection 41 4.6 SYSTEM TEST 41 5 SYSTEM MONITORING &CONFIGURATION 43 5.1 ACCESSING EMS LOCAL GUI 43 5.1.1 Using Ethernet Port 43 5.1.2 Using USB Port 44 5.1.3 Login to EMS Local GUI 45 5.2 NAV I G AT I N G T H E EMS LOCAL GUI 47 5.2.1 Topology Tool Bar 48 5.2.2 Upgrade/Password Functions 49 5.3 INSTALLATION & CONFIGURATION 49 5.3.1 Network & Communications 49 5.3.2 System Installation 51 5.3.3 Alarms 56 5.4 SYSTEM TUNING 58 5.4.1 BTS Signal Conditioning 58 5.4.2 Set Downlink Gain 58 5.4.3 Set Uplink Gain 61 5.4.4 Link Verification 63 5.5 MONITORING AND ALARMS 65 5.5.1 Operational Status 65 5.5.2 System Alarms 67 5.6 SYSTEM UPGRADE 68 5.6.1 Verify Software Versions 68 5.6.2 Upgrade component software 68 6 MAINTENANCE 69 mBSC0800S-005-RUCM11 ©1999-2013 Bravo Tech Inc. 6.1 ELECTROSTATIC DISCHARGE PRECAUTIONS 69 6.2 PREVENTATIVE MAINTENANCE 69 6.3 FAULT DETECTION AND ALARM REPORTING 69 6.4 TROUBLESHOOTING QUICK GUIDE 70 6.4.1 Host Unit Trouble Shooting 71 6.4.2 Remote Unit Trouble Shooting 72 7 TERMS, ACRONYMS & ABBREVIATIONS 73 8 PACKING LIST 74 mBSC0800S-005-RUCM11 ©1999-2013 Bravo Tech Inc. LIST OF FIGURES FIGURE 1BLOCK DIAGRAM OF HOST UNIT.................................................................................................................................1 FIGURE 2 BLOCK DIAGRAM OF REMOTE NODE..........................................................................................................................2 FIGURE 3MBSC SYSTEM FUNCTIONAL OVERVIEW.....................................................................................................................5 FIGURE 4 HOST UNIT..................................................................................................................................................................7 FIGURE 5BIU ..............................................................................................................…

Text truncated - open the document above for the full version.

Bravo Tech (Shenzhen) Co. Ltd. No. 8 Building, The 3rd Zone, Tangtou Industrial Park Shiyan, Baoan District, Shenzhen, China DATE :2015-5-18 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Hank.Yan of Global United Technology Services Co., Ltd. 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District Shenzhen Guangdong to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Bravo Tech (Shenzhen) Co. Ltd. and No. 8 Building, The 3rd Zone, Tangtou Industrial Park Shiyan, Baoan District, Shenzhen, China Dated this / Day of 5/18/2015 / Agency agreement expiration date: 5/18/2016 By: Bailey Zheng Signature Printed Title: COO On behalf of : Bravo Tech (Shenzhen) Co. Ltd. Telephone: +1-714-230-8333

Bravo Tech (Shenzhen) Co. Ltd. No. 8 Building, The 3rd Zone, Tangtou Industrial Park Shiyan, Baoan District, Shenzhen, China 2015-5-18 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: WBKMBSC08S005RUM Product Name: mBSC-C RUM Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operational Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 5/18/2015 By: Bailey Zheng Signature Printed Title: COO On behalf of : Bravo Tech (Shenzhen) Co. Ltd. Telephone: +1-714-230-8333

Bravo Tech (Shenzhen) Co. Ltd. No. 8 Building, The 3rd Zone, Tangtou Industrial Park Shiyan, Baoan District, Shenzhen, China 2015-7-8 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: WBKMBSC08S005RUM Product Name: mBSC-C RUM Request for Warning Label (1) Warning label messages and Class B disclosure will be also shown in online and point-of-sale marketing materials and on outside packaging of device. Dated this 7/8/2015 By: Bailey Zheng SignaturePrinted Tit le: COO On behalf of : Bravo Tech (Shenzhen) Co. Ltd. Tele phone: +1-714-230-8333

RUM- Front view RUM- Rear view RUM- Top view RUM- Bottom view RUM- Left view RUM- Right view

Label location

Size: 60mm*30mm Size: 60mm*20mm

mBSC0800S-005-RUCM11 Tune up procedure Tune up procedure mBSC0800S-005-RUCM11 V1.0 November 16, 2014 1 mBSC0800S-005-RUCM11 Tune up procedure 1. purpose This manual is intended to document the design and structure of the MBSC0800S-005-RUCM11 test, with all other relevant topics to provide users with instructions on its usage and maintenance. 2. Hardware Test setup consists of some instrument, a computer system and software, table 1 contains a list of the included equipment and components. Figure 1 show s the setup for DAS system test. Table 1: List of equipment Qty. Description Manufacture Part Number Option Comments 1 Signal generator IRF IRF3413 Or Equivalent 1 Spectrum analyzer R&S FSEA Or Equivalent 2 Power meter Agilent E4418B Or Equivalent 1 Power supply Lambda GN60-55 Or Equivalent 1 RS232 serial cable 1 150W attenuator 30dB HuaXiang 2 Wideband coupler 20dB HuaXiang 1 10W attenuator 20dB HuaXiang 1 Computer workstation IBM 4 RF cable 2 meter Figure 1: Downlink test setup 3. Calibration We must measure the insertion loss form MBSC system output port to output power meter sensor, and set the value to output power meter and spectrum analyzer as offset; Setting the coupling ratio of input coupler to input power meter as offset; 4. Interface introduce Host unit interface Figure 3: Host unit interface 2 mBSC0800S-005-RUCM11 Tune up procedure PSU 1 0 PSU 1 0 FIU Opreate FIBER2 TX2 RX2 FIBER1 TX1 RX1 FIU Opreate FIBER2 TX2 RX2 FIBER1 TX1 RX1 BIU Opreate Tx700 Rx4 IN Rx3 IN Rx2 IN Rx1 IN Tx4 OUT Tx3 OUT Tx2 OUT Tx1 OUT Tx850 Tx1900 Tx2100 Tx2600 Rx700 Rx850 Rx1900 Rx2100 Rx2600 RCU Opreate RJ45 RS232 Modem USB Composite RF Tx Connector (1~2) Composite RF Rx Connector (1~2) Optical Transceiver Port (1~2) LED Indicator Power ON/OFF Switch Ethernet Connector 5-band RF Tx Connector (1~4) RF Rx Connector (700~2600MHz) RF Tx Connector (700~2600MHz) 5-band RF Rx Connector (1~4) Serial Port External Wired Modem Connector Remote unit interface Figure 4: Remote unit interface 5. Adjustment description Downlink test 1). Set up the structure according to the figure 1. 2). Connect the signal generator to TX-1 port or TX-2 port of Host unit BIU module, connect the Remote unit and Host unit with fiber cable, output signal comes from 3 mBSC0800S-005-RUCM11 Tune up procedure ANT port of 0800RUM. 3). Signal generator setup: Signal type: RFN11_Spaced_5MHz_1489 Frequency allocation: Lower frequency: 855MHz Middle frequency: 860MHz High frequency: 865MHz. 4). Spectrum analyzer setup: RBW→30KHz; VBW→300KHz; SPAN: 30MHz; Sweep time: 1S; Spectrum Analyzer’s offset value according the attenuation from PA output to input port of spectrum analyzer. 5). Power meter must to be calibration and set the offset value according to attenuation from PA output to power sensor. 6). Turn on the signal generator. 7). than confirm standard Unwanted emissions etc. 4

RF Exposure Evaluation 1 Applicable Standard According to RSS-102 RF exposure is calculated. Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field (V/m rms) Magnetic Field (A/m rms) Power Density (W/m 2 ) Averaging Time (minutes) 0.003-1 280 2.19 - 6 1-10 280/ƒ 2.19/ƒ - 6 10-30 28 2.19/ƒ - 6 30-300 28 0.073 2 * 6 300-1500 1.585 ƒ 0.5 0.0042 ƒ 0.5 ƒ/150 6 1500-15000 61.4 0.163 10 6 15000-150000 61.4 0.163 10 616000/ƒ 1.2 150000-300000 0.158 ƒ 0.5 4.21 x 10 -4 ƒ 0.5 6.67 x 10 -5 ƒ 616000/ƒ 1.2 Note: ƒ is frequency in MHz. * Power density limit is applicable at frequencies greater than 100 MHz. 2 MPE Prediction Predication of MPE limit at a given distance, Equation from OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to the antenna G = numeric gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the centre of radiation of the antenna Maximum peak output power at antenna input terminal (dBm): 36.28 Maximum peak output power at antenna input terminal (mW): 4246 Maximum antenna gain: (dBi): 9.8 Maximum Antenna Gain (numeric): 53.25 Prediction distance (cm): 600 Prediction frequency (MHz): 856.5125 Power density at predication frequency and distance (mW/cm2): 0.05 MPE limit for uncontrolled exposure at predication frequency (mW/cm2): 0.57 Conclusion: compliant

Global United Technology Services Co., Ltd. Report No.: GTSE15050073201 Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of GTS or testing done by GTS in connection with, distribution or use of the product described in this report must be approved by GTS in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only FCC REPORT Applicant: Bravo Tech (Shenzhen) Co. Ltd. Address of Applicant: No. 8 Building, The 3rd Zone, Tangtou Industrial Park Shiyan, Baoan District, Shenzhen, China Equipment Under Test (EUT) Product Name: mBSC-C RUM Model No.: mBSC0800S-005-RUCM11 FCC ID: WBKMBSC08S005RUM Applicable standards: FCC CFR Title 47 Part 2:2014 FCC CFR Title 47 Part 20:2014 FCC CFR Title 47 Part 90 Subpart I:2014 Date of sample receipt: May 04 2015 Date of Test: May 04-15, 2015 Date of report issued: May 18, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSE15050073201 Global United Technology Services Co., Ltd. Project No.: GTSE150500732RF Room 301-309, 3th Floor, Block A, Huafeng Jinyuan Business Building, No. 300 Laodong Industrial Zone,Xixiang Road, Baoan District, Shenzhen 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 93 2 Version Version No. Date Description 00 May 18, 2015 Original Prepared By: Date: May 18, 2015 Project Engineer Check By: Date: May 18, 2015 Reviewer Report No.: GTSE15050073201 Global United Technology Services Co., Ltd. Project No.: GTSE150500732RF Room 301-309, 3th Floor, Block A, Huafeng Jinyuan Business Building, No. 300 Laodong Industrial Zone,Xixiang Road, Baoan District, Shenzhen 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 93 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 VERSION .................................................................................................................................................... 2 3 CONTENTS ................................................................................................................................................ 3 4 TEST SUMMARY ....................................................................................................................................... 5 5 GENERAL INFORMATION ........................................................................................................................ 6 5.1 CLIENT INFORMATION............................................................................................................................ 6 5.2 GENERAL DESCRIPTION OF EUT ........................................................................................................... 6 5.3 RELATED SUBMITTAL(S) / GRANT (S) ..................................................................................................... 7 PRIVATE LAND MOBILE RADIO SERVICES................................................................................................. 7 COMMERCIAL MOBILE SERVICES .............................................................................................................. 7 5.4 TEST METHODOLOGY............................................................................................................................ 7 5.5 DESCRIPTION OF SUPPORT UNITS......................................................................................................... 7 5.6 TEST FACILITY...................................................................................................................................... 7 5.7 TEST LOCATION.................................................................................................................................... 8 5.8 TEST INSTRUMENTS LIST....................................................................................................................... 9 6 TEST CONFIGURATION AND CONDITIONS......................................................................................... 10 6.1 EUT CONFIGURATION......................................................................................................................... 10 6.2 CONFIGURATION OF TESTED SYSTEM.................................................................................................. 11 6.3 TEST ENVIRONMENTS......................................................................................................................... 13 6.4 TEST FREQUENCY SELECTION.............................................................................................................. 14 6.5 DESCRIPTION OF TEST MODES................................................................................................... 14 7 RF POWER OUTPUT(ERP) MEASUREMENT ....................................................................................... 15 7.1 STANDARD APPLICABLE.......................................................................…

Text truncated - open the document above for the full version.

Radiated Emission Conducted Emission