WD9-GW2010Gateway transmitter

Vue Features Expand your Vue It’s easy to add cameras and mounts so you can expand your view to see more locations around your home...or anywhere! See more cameras and accessories at VueZone.com Vue cameras Motion sensor Camera sync button Automatically connects all your Vue cameras Sync LED This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. · Reorient or relocate the receiving antenna · Increase the separation between the equipment and receiver · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected · Consult the dealer or an experienced radio/TV technician for help Caution: Exposure to radio frequency radiation To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Battery door/mount Battery door latch & on/off switch (on camera bottom) Lens Quick Install Guide Visit VueZone.com to learn more. Avaak, Inc. 9645 Scranton Road, Suite 110 San Diego, CA 92121 www.avaak.com © 2010. All rights reserved. Vue, the Vue logo, FrameMesh and See what you’re missing are trademarks of Avaak, Inc. Designed in California. Product made in China. AV16-00213 REV 08.10 Support VueZone.com/support Welcome! Thank you for choosing Vue. Now let’s get started...it’s easy! What’s in the box All you need is a high-speed internet connection and available LAN port on your router. Personal Video Network Personal Video Network Your Gateway VGN number: Vue gateway Sync LED Power LED Confirms your Vue gateway is powered on Internet LED Confirms your Vue gateway is connected to the internet Vue Status LED Confirms your Vue network is operating Need Help? ? We’re here to help! Please register your system to take advantage of the in-depth resources available as my.VueZone.com user. Click the Help link in the upper right of any my.VueZone.com page to access these resources, as well as a comprehensive Vue User Guide. If you haven’t registered yet, please visit our website at VueZone.com/support to find answers to the most common questions. Installation tips can be found at VueZone.com/install Email support: [email protected] Phone support: 888.636.9883 Amber LED Green LED Power connector Reset pinhole Ethernet connector USB connector 1. Connect the Ethernet cable to the Ethernet port on the gateway and to an available LAN port on your router.* 2. Connect the power adapter to the gateway and power outlet. The blue Power LED will be on. 3. The blue Internet LED will flash continuously if you have a valid connection. The initial flash may take up to 2 minutes. Before syncing, confirm that the Internet LED on the gateway front is continuously blinking. If not, go to VueZone.com/install to troubleshoot, or contact Vue support. 1. Press and release the Sync button on the top of the gateway. Blue Sync LED will turn on for 45 seconds. 2. If you cannot complete the camera syncing operation in 45 seconds, Sync button must be pressed again. Gateway 3. Place camera within 12 inches of the gateway and slide camera power switch to the ON position (green dot showing). 4. Watch the camera front – blue camera LED will blink for 5 seconds to confirm sync. 5. Once synced, cameras can be viewed and positioned. Tip: the email ID you use to register your system will also be used to send you vital communications and answer support inquiries. Tip: it’s easy to aim your cameras using VueZone Mobile for your smartphone – see the last panel of this Guide for details. 1. Peel off the adhesive protective layer on the back of the mounting ball. Select a location where you want to install the camera and stick the mounting ball to surface. Alternatively, install the included mounting screw in the desired position, and hang the mounting ball from the screw head. 2. Place the camera on the mounting ball and point the lens in the desired direction. 3. Adjust your camera position by viewing the image through your my.VueZone.com account on your computer browser or VueZone Mobile app. Tip: special camera mounts for windows and tabletops are available at VueZone.com * If you are installing a network for the first time please follow the network installation instructions for your router first. 1. Locate your VGN number on the back panel of this Quick Install Guide or on the bottom of the gateway. 2. Go to my.VueZone.com and click the button. 3. Follow the on-screen instructions to register your system. 1. To confirm that your cameras have synced to the gateway, your active cameras (not grayed out) should appear in the My Cameras area on your Watch Page at my.VueZone.com. 2. Drag a camera icon from the My Cameras area into the My Vue area on the right. 3. Click on the cam…

Text truncated - open the document above for the full version.

August 25, 2010 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: WD9-GW2010 Authority to Act as Agent On our behalf, I appoint Alan Laudani of Nemko USA Inc., 11696 Sorrento Valley Rd, San Diego, CA, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communication Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Avaak, Inc. 5405 Morehouse Dr., San Diego, CA 92121. This appointment is in effect until December 1, 2010. Sincerely yours,

Jan. 19, 2011 Nemko 11696 Sorrento Valley Rd. San Diego CA, 92121 USA Re: Request of Confidentiality for FCC ID: WD9-GW2010 Pursuant to Sections 0.457(d)(I)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: Schematics, Parts List, Operating Description, Block Diagrams The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(I)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. Sincerely,

1 1 6 1 2 1 4 1 5 1 9.6 12.6 A 7 1 3 1 0.30 DETAIL A SCALE 2 : 1.5 1 NOTES UNLESS OTHERWISE SPECIFIED: ENCLOSURE MUST PASS FINAL SYSTEM TEST PER LATEST TEST PROCEDURE.1. PLACE SYSTEM LABEL AS SHOWN IN BOTTOM VIEW. DIMENSIONS ARE IN MILLIMETER.2. UNIT SHALL BE FREE OF COSMETIC DEFECTS: SCRATCH, CRACK, CHIP, FADING, AND SPLATTER PAINT.3. BODY COLORS AND TEXT COLORS SHALL BE CONFORMING WITH ARTWORK DRAWINGS AND ITS 4. SPECIFICATIONS. USE PAINT CHIP TO CHECK BODY COLORS. 1 THE GAP BETWEEN HOUSINGS SHALL NOT EXCEED 0.30MM. THE GAP SHALL BE VISUALLY UNIFORMED 5. FROM THE BEGINNING TO THE END; THE DIFFERENCE SHALL BE WITHIN +/- .05mm. "SYNC" BUTTON SHALL BE CHECKED BY PRESSING IT AND MECHANICAL CLICK NOISE IS AUDIBLE.6. ITEM NO. QTY PART NUMBER DESCRIPTION 11AV11-00258Gateway Assembly, Gen2 21AV13-00256Button, Gateway II 31AV13-00035Insert, Bottom, Gateway 41AV13-00126Housing, Right Gateway, RL 51AV19-00135Artwork, Gateway back panel 61AV11-00224Lens, Gateway with VUE Logo 71AV17-00335Label, Mac Address/VGN 81AV16-00321Test Procedure, GateWay Enclosed, Final REVISIONS ECOREV.DESCRIPTIONDATEAPPROVED N/AAInitial Manufacturing Release8-23-2010L. Hin D C B A A B C D 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 1 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF AVAAK INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF AVAAK INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC TOLERANCING PER: ASME Y14.5M FINISH DRAWN CHECKED ENG APPR. MFG ENG APPR. Q.A. COMMENTS: DATE NAME TITLE: SIZE B DWG. NO. REV SCALE: 1:1 UNLESS OTHERWISE SPECIFIED A L. Hin SHEET 1 OF 1 AV11-00255 DO NOT SCALE DRAWING AVAAK INC. 9645 SCRANTON RD., #110 SAN DIEGO, CA 92121 MATERIAL MFG APPR. TOLERANCES .XXX .003 .XX .02 .X .1 Enclosed, Gateway II L. Hin 2010 Jul 30 NONE 2010 Jul 30 INCHESMILLIMETER .XX [.10] .X [.25] X [1.0] ANGULAR 0 BEND 1 DEPT

C M Y CM MY CY CMY K Vue_Gateway_Label_Gen2C_3.pdf 8/25/10 4:30:00 PM

Evaluation of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01where: S = power density P = power input to the antennaG = power gain of the antenna in the direction of interest relative to an isotropic radiatorR = distance to the center of radiation of the antenna Maximum peak output power --Conducted 24.73 dBm 0.297 (W) Antenna gain(typical): 0.00 (dBi) Maximum antenna gain: 1.00 (numeric) Evaluation distance: 20.00 (cm) Evaluation frequency: 2404.00 (MHz) Limit from table below: 1 (mW/cm^2) Power density at Evaluation frequency: 0.059 (mW/cm^2) EUT complies FCC/LSGAC Local Official’s Guide to RFA LOCAL GOVERNMENT OFFICIAL'S GUIDE TO TRANSMITTING ANTENNA RFEMISSION SAFETY: RULES, PROCEDURES, AND PRACTICAL GUIDANCE 2 4 R PG S π =

Nemko USA, Inc. 11696 Sorrento Valley Rd., Suite F San Diego, CA 92121-1024 Phone (858) 755-5525 Fax (858) 452-1810 FCC Part 15 Subpart C, 15.247 : 28/01/2011 CERTIFICATION TEST REPORT Report Number: 2010 08154507 FCC2 Project Number: 54533-1 Applicant: Avaak 5405 Morehouse Dr. San Diego, CA 92121 Equipment Under Test (EUT): Wireless Gateway Model: GW2010 FCC ID: WD9-GW2010 IC: 7764A-GW2010 In Accordance With: FCC Part 15 Subpart C, 15.247 RSS-210, Issue 7, June 2007 Tested By: Nemko USA Inc. 11696 Sorrento Valley Road, Suite F San Diego, CA 92121 Authorized By: Alan Laudani, Wireless/EMC Engineer Date: August 10, 2010 Total Number of Pages: 44 Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2010 08154507 FCC2 FCC ID: WD9-GW2010 IC: 7764A-GW2010 Specification: FCC Part 15 Subpart C, 15.247 RSS-210 Issue 7, June 2007 _____________________________________________________________________________________________ Page 2 of 42 DOCUMENT HISTORY REVISION DATE COMMENTS - August 10, 2010 Prepared By: A. Laudani - August 10, 2010 Initial Release: A. Laudani NOTE: Nemko USA, Inc. hereby makes the following statements so as to conform to Chapter 10 (Test Reports) Requirements of ANSI C63.4 (2003) “Methods and Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz”: o The unit described in this report was received at Nemko USA, Inc.'s facilities on August 2, 2010. o Testing was performed on the unit described in this report on August 2, 2010 to August 4, 2010. o The Test Results reported herein apply only to the Unit actually tested, and to substantially identical Units. o This report does not imply the endorsement of the Federal Communications Commission (FCC), Industry Canada, NVLAP or any other government agency. This Report is the property of Nemko USA, Inc., and shall not be reproduced, except in full, without prior written approval of Nemko USA, Inc. However, all ownership rights are hereby returned unconditionally to Avaak, and approval is hereby granted to Avaak, and its employees and agents to reproduce all or part of this report for any legitimate business purpose without further reference to Nemko USA, Inc. Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2010 08154507 FCC2 FCC ID: WD9-GW2010 IC: 7764A-GW2010 Specification: FCC Part 15 Subpart C, 15.247 RSS-210 Issue 7, June 2007 _____________________________________________________________________________________________ Page 3 of 42 Section 1. Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15; Subpart C. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: Wireless Gateway Model GW2010 Specification: FCC Part 15 Subpart C, 15.247 IC RSS-210 Issue 7 June 2007 Annex 8 IC RSS-Gen Issue 2 June 2007 Date Received in Laboratory: August 2, 2010 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2010 08154507 FCC2 FCC ID: WD9-GW2010 IC: 7764A-GW2010 Specification: FCC Part 15 Subpart C, 15.247 RSS-210 Issue 7, June 2007 _____________________________________________________________________________________________ Page 4 of 42 CERTIFICATION Nemko USA, Inc., an independent Electromagnetic Compatibility (EMC) Test Laboratory, produced this Test Report and performed the Radio Frequency Interference (RFI) testing and data evaluation contained herein. Nemko USA, Inc.’s measurement facility is currently registered with the United States Federal Communications Commission (FCC) in accordance with the provisions of 47 United States Code (CFR) Part 2, Subpart I, Section 2.948(a). A current description of Nemko USA, Inc.’s measurement facility is on file with the FCC. Nemko USA Inc. has additionally satisfied the FCC that it complies with the requirements set forth in 47 CFR Part 2, Subpart I, Section 2.948(d) regarding the accreditation of EMC laboratories. The RFI testing, test data collection and test data evaluation were accomplished in accordance with the ANSI C63.4–2003 Standard, and in accordance with the applicable sections of the FCC rules (47 CFR Parts 2 and 15). The testing was also accomplished in accordance with Industry Canada's ICES-003 standard for unintentional radiating device per EMCAB-3, Issue 3 (May 1998). The administrative summary of this test report provides a description of the test sample. I hereby certify that the test data, test data evaluation, and equipment configurations used to compile this test report are a true and accurate representation of the test sample’s radio frequency interference characteristics as of the test date(s), and, for the design of the test sample. TESTED BY: Date: August 10, 2010 A. Laudani, EMC Test Engineer Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2010 08154507 FCC2 FCC ID: WD9-GW2010 IC: 7764A-GW2010 Specification: FCC Part 15 Subpart C, 15.247 RSS-210 Issue 7, June 2007 _____________________________________________________________________________________________ Page 5 of 42 TABLE OF CONTENTS Section 1. Summary of Test Results ............................................................................... 3 Section 2: Equipment Under Test ................................................................................... 6 2.1 Product Description...................................................................................…

Text truncated - open the document above for the full version.