WQ8-2013J2534J2534 ECU PROGRAMMING DEVICE

J2534 ECU PROGRAMMING DEVICE MaxiFlash pro ii Trademarks Autel ® , MaxiSys TM , MaxiDAS ® , MaxiScan ® , MaxiTPMS ® , MaxiVideo TM , MaxiRecorder TM , and MaxiCheck TM are trademarks of Autel Intelligent Technology Co., Ltd, registered in China, the United States and other countries. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Autel. Disclaimer of Warranties and Limitation of Liabilities All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Autel reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given to the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Autel will not be liable for any direct damages or for any special, incidental, or indirect damages or for any economic consequential damages (including lost profits). IMORTANT: Before operating or maintaining this unit, please read this manual carefully paying extra attention to the safety warnings and precautions. For Services and Support: www.maxidas.com www.auteltech.com 1-877-288-3587/1-877-AUTELUS (North America) 0086-755-86147779 (China) [email protected] For technical assistance in all other markets, please contact your local selling agent iii Safety Information For your own safety and the safety of others, and to prevent damage to the equipment and vehicles upon which it is used, it is important that the safety instructions herein presented throughout this manual be read and understood by all persons operating, or coming into contact with, the equipment. There are various procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the individual doing the work. Because of the vast number of test applications and variations in the products that can be tested with this instrument, we cannot possibly anticipate or provide advice or safety messages to cover every situation. It is the automotive technician’s responsibility to be knowledgeable of the system being tested. It is essential to use proper service methods and test procedures. It is important to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the equipment being used, or the vehicle being tested. Before using the equipment, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the equipment only as described in this manual. Read, understand, and follow all safety messages and instructions in this manual. Safety Messages Safety messages are provided to help prevent personal injury and equipment damage. All safety messages are introduced by a signal word indicating the hazard level. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders. Safety Instructions The safety messages herein cover situations Autel is aware of. Autel cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered do not jeopardize your personal safety. DANGER: When an engine is operating, keep the service area WELL VENTILATED or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless, poisonous gas that causes slower reaction time and can lead to serious personal injury or loss of life. Safety Information Important Safety Insturctions iv WARNINGS:  Always perform automotive testing in a safe environment.  Wear safety eye protection that meets ANSI standards.  Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.  Operate the vehicle in a well ventilated work area, for exhaust gases are poisonous.  Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.  Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.  Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.  Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.  Do not connect or disconnect any test equipment while the ignition is on or the engine is running.  Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.  Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.  Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment.  To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.  Do not place the test equipment on the distributor of the vehicle. Strong electro-magnetic interference can damage the equipment. v Contents SAFETY INFORMATION ........................................................................................... III CHAPTER 1 USING THIS MANUAL .......................…

Text truncated - open the document above for the full version.

Shenzhen Autel Intelligent Tech. Co., Ltd. East Gate, the 1st Floor of SZICC Bldg, Chaguang Road 1089, Xili Town, Nanshan District, Shenzhen, China DATE :2013-11-01 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Hans.Hu of Global United Technology Services Co., Ltd. 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District Shenzhen Guangdong (Name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Shenzhen Autel Intelligent Tech. Co., Ltd. and East Gate, the 1st Floor of SZICC Bldg, Chaguang Road 1089, Xili Town, Nanshan District, Shenzhen, China ( applicant name and address). Dated this / Day of 11/01/2013 / Agency agreement expiration date: 11/01/2014 By: Frank Li Signature Printed Title: Manager On behalf of : Shenzhen Autel Intelligent Tech. Co., Ltd. Telephone: 0755-86329573

Shenzhen Autel Intelligent Technology Co., Ltd. Date: 11/01/2013 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD To Whom It May Concern: MaxiSys Display Tablet and VCI – Bluetooth Diagnostic Interface, which exhibited in the user manual are not included in FCC approval of FCC ID: WQ8-2013J2534 FCC ID: WQ8-2013J2534 is only for VCI – J2534 ECU Programming Device which listed in user manual If you have any question or concerns, pls. contact us. Sincerely, Client’s signature Client’s name / title Frank Li / Manager Contact information / address Tel: 0755-86329573 Address: East Gate, the 1st Floor of SZICC Bldg, Chaguang Road 1089, Xili Town, Nanshan District, Shenzhen, China

Date: 11/01/2013 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: WQ8-2013J2534 To Whom It May Concern: We, Shenzhen Autel Intelligent Tech. Co., Ltd., are applying FCC DOC for product J2534 ECU PROGRAMMING DEVICE which model no. is MaxiFlash pro. the FCC DOC is doing at proper FCC authorized and recognized lab, and FCC DOC will be issued soon. If you have any question or concerns, pls. contact us. Sincerely, Client’s signature Client’s name / title Frank Li / Manager Contact information / address Tel: 0755-86329573 Address: East Gate, the 1st Floor of SZICC Bldg, Chaguang Road 1089, Xili Town, Nanshan District, Shenzhen, China

Shenzhen Autel Intelligent Tech. Co., Ltd. East Gate, the 1st Floor of SZICC Bldg, Chaguang Road 1089, Xili Town, Nanshan District, Shenzhen, China 2013-11-01 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: WQ8-2013J2534 Product Name: J2534 ECU PROGRAMMING DEVICE Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operational Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 11/01/2013 By: Frank Li Signature Printed Title: Manager On behalf of : Shenzhen Autel Intelligent Tech. Co., Ltd. Telephone: 0755-86329573

Shenzhen Autel Intelligent Technology Co., Ltd. J2534 ECU PROGRAMMING DEVICE M/N: MaxiFlash pro FCC ID: WQ8-2013J2534 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Rate: DC 12V 2A Output: DC 12V Max. 0.2A

Label location

RF Antenna

RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation For 2402-2480MHz: Max Pk Ouput power is 47.10mW Ant Gain=2.5dBi G=1.778 The distance between user and EUT is at least 20cm . So Pd= 47.10*1.778/(4*3.14*20*20)= 0.016669<1mW/cm2

Global United Technology Services Co., Ltd. Report No.: GTSE13090163101 Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of GTS International Electrical Approvals or testing done by GTS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by GTS International Electrical Approvals in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page FCC Report Applicant: Shenzhen Autel Intelligent Technology Co., Ltd. Address of Applicant: East Gate, the 1st Floor of SZICC Bldg, Chaguang Road 1089, Xili Town, Nanshan District, Shenzhen, China Equipment Under Test (EUT) Product Name: J2534 ECU PROGRAMMING DEVICE Model No.: MaxiFlash pro Trade Mark: AUTEL FCC ID: WQ8-2013J2534 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247:2012 Date of sample receipt: October 24, 2013 Date of Test: October 25-30, 2013 Date of report issued: October 31, 2013 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSE13090163101 Global United Technology Services Co., Ltd. Project No.: GTSE130901631RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 53 2 Version Version No. Date Description 00 October 31, 2013 Original Prepared By: Date: October 31, 2013 Project Engineer Check By: Date: October 31, 2013 Reviewer Report No.: GTSE13090163101 Global United Technology Services Co., Ltd. Project No.: GTSE130901631RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 53 3 Contents Page 1 COVER PAGE........................................................................................................................................................1 2 VERSION.................................................................................................................................................................2 3 CONTENTS.............................................................................................................................................................3 4 TEST SUMMARY...................................................................................................................................................4 5 GENERAL INFORMATION..................................................................................................................................5 5.1 CLIENT INFORMATION...................................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT.................................................................................................................... 5 5.3 TEST MODE...................................................................................................................................................... 7 5.4 TEST FACILITY................................................................................................................................................. 7 5.5 TEST LOCATION............................................................................................................................................... 7 5.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER................................................................................. 7 5.7 DESCRIPTION OF SUPPORT UNITS.................................................................................................................. 7 6 TEST INSTRUMENTS LIST.................................................................................................................................8 7 TEST RESULTS AND MEASUREMENT DATA...............................................................................................9 7.1 ANTENNA REQUIREMENT................................................................................................................................. 9 7.2 CONDUCTED EMISSIONS...............................................................................................................................10 7.3 CONDUCTED PEAK OUTPUT POWER............................................................................................................ 13 7.4 20DB EMISSION BANDWIDTH........................................................................................................................ 17 7.5 CARRIER FREQUENCIES SEPARATION.......................................................................................................... 21 7.6 HOPPING CHANNEL NUMBER........................................................................................................................ 25 7.7 DWELL TIME..........................................................................................................…

Text truncated - open the document above for the full version.

Radiated Emission Conducted Emission