WQ8-V150DC2241MaxiVCI V150

i Trademarks Autel ® , MaxiSys ® , MaxiDAS ® , MaxiScan ® , MaxiTPMS ® , MaxiRecorder ® , and MaxiCheck ® are trademarks of Autel Intelligent Technology Corp., Ltd., registered in China, the United States and other countries. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of Autel. Disclaimer of Warranties and Limitation of Liabilities All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Autel reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Autel will not be liable for any direct, special, incidental, indirect damages or any economic consequential damages (including the loss of profits). IMPORTANT Before operating or maintaining this unit, please read this manual carefully, paying extra attention to the safety warnings and precautions. For Services and Support pro.autel.com www.autel.com 1-855-288-3587/1-855-AUTELUS (North America) 0086-755-86147779 (China) [email protected] For technical assistance in all other markets, please contact your local selling agent. ii Safety Information For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device. There are various procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician’s responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested. Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Read, understand, and follow all safety messages and instructions in this manual. Safety Messages Safety messages are provided to help prevent personal injury and equipment damage. All safety messages are introduced by a signal word indicating the hazard level. DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders. iii Safety Instructions The safety messages herein cover situations Autel is aware of. Autel cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety. DANGER When an engine is operating, keep the service area WELL VENTILATED or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless, poisonous gas that causes slower reaction time and can lead to serious personal injury or loss of life. SAFETY WARNINGS Always perform automotive testing in a safe environment. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts. Operate the vehicle in a well ventilated work area, for exhaust gases are poisonous. Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged. Put blocks in front of the drive wheels and never leave the vehicle unattended while testing. Be extra cautious when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running. Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby. Do not connect or disconnect any test equipment while the ignition is on or the engine is running. Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary. Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident. iv Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment. To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure. Do not place the test equipment on the distributor of the vehicle. Strong electro-magnetic interference can damage the equipment. 1 Using This Manual This manual contains device usage instructions. Some illustrations shown in this manual may contain modules and optional equipment that are not included in your system. Contact your sales representative for availability of other modules and optional tools or accessories. Conventions The following conventions are used. Bold Tex…

Text truncated - open the document above for the full version.

Autel Intelligent Technology Corp.,Ltd. Address: 7th-8th,10th Floor, Building B1, Zhiyuan, Xueyuan Rd, Xili, Nanshan, Shenzhen, 518055 China Date: March 15, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: WQ8-V150DC2241 Autel US, Inc – Attestation Statement / Part 2.911(d)(7) Autel Intelligent Technology Corp.,Ltd. certifies, that as of March 15, 2023, we have designated Autel US, Inc to accept service of process on our behalf for FCC ID: WQ8- V150DC2241. Autel Intelligent Technology Corp.,Ltd. accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Autel US, Inc, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Autel Intelligent Technology Corp.,Ltd. for FCC ID: WQ8- V150DC2241. Designated Agent Information: Company Name: Autel US, Inc Address: 36 Harbor Park Drive, Port Washington, NY 11050-4651,United States FRN: 0032544660 Contact Person: Paul A Marshall Telephone No: (855) 288-3587 Email: [email protected] Fax No: (631) 357-3304 Sincerely, Company: Autel Intelligent Technology Corp.,Ltd. Designated Agent: Autel US, Inc Company Representative: Frank Li Designated Agent Representative: Paul A Marshall Signature: Signature:

Sincerely, Name/Title： Frank Li/President Company: Autel Intelligent Tech. Corp., Ltd. Address: 7th-8th,10th Floor, Building B1, Zhiyuan, Xueyuan Rd, Xili, Nanshan, Shenzhen, 518055 China Phone: (86)755-86147779 Fax: (86)755-86147758 E-Mail: [email protected]

Page 1 of 3 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. External Photos Photo 1 Photo 2 Page 2 of 3 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Photo 3 Photo 4 Page 3 of 3 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Photo 5 Photo 6 ------End------

Label Model/HVIN:MaxiVCI V150 FCC ID: WQ8-V150DC2241 IC: 10826A-V150DC2241

Page 1 of 4 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Internal Photos Photo 1 Photo 2 Page 2 of 4 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Photo 3 Photo 4 Page 3 of 4 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Photo 5 Photo 6 Antenna Page 4 of 4 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Photo 7 Photo 8 ------End------

Page 1 of 2 Report No.: AIT23010918FH1 RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description MaxiVCI V150 Model Name MaxiVCI V150 FCC ID WQ8-V150DC2241 2. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure requirement KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 3. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation Page 2 of 2 Report No.: AIT23010918FH1 • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 4. Manufacturing Tolerance Mode Max. Peak Conducted Output Power (dBm) Max. tune-up BT -0.11 0±1 5. Standalone MPE Result Antenna 1 Band/Mode f (GHz) Antenna Distance (mm) RF output power including tune up SAR Test Exclusion Threshold SAR Test Exclusion Estimated SAR dBm mW BT 2.5 5 1 1.26 0.398< 3 Yes 0.0531 Note: Only the worst case recorded. 6. Conclusion ： Compliance the RF exposure requirement

Page 1 of 38 Report No.: AIT23010918W1 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. TEST REPORT Client Information: Applicant: Autel Intelligent Tech.Corp., Ltd. Applicant add.: 7th-8th,10th Floor, Building B1, Zhiyuan, Xueyuan Rd, Xili, Nanshan, Shenzhen, 518055 China Manufacturer: Autel Intelligent Tech.Corp., Ltd. Manufacturer add.: 7th-8th,10th Floor, Building B1, Zhiyuan, Xueyuan Rd, Xili, Nanshan, Shenzhen, 518055 China Product Information: Product Name: MaxiVCI V150 Model No.: MaxiVCI V150 Brand Name: AUTEL FCC ID: WQ8-V150DC2241 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Prepared By: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang,Dongguan, Guangdong, China Tel.: +86-769-8202 0499 Fax.: +86-769-8202 0495 Date of Receipt: Jan. 09, 2023 Date of Test: Jan. 09, 2023~ Jan. 30, 2023 Date of Issue: Jan. 31, 2023 Test Result: Pass This device described above has been tested by Dongguan Yaxu (AiT) Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Dongguan Yaxu (AiT) Technology Limited, this document may be altered or revised by Dongguan Yaxu (AiT) Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Simba Huang Seal.chen Page 2 of 38 Report No.: AIT23010918W1 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. 1 Contents Page COVER PAGE 1 CONTENTS .................................................................................................................................................................... 2 2 TEST SUMMARY .......................................................................................................................................................... 4 2.1 Statement of the Measurement Uncertainty .............................................................................. 4 2.2 Measurement Uncertainty ......................................................................................................... 4 3 TEST FACILITY ............................................................................................................................................................. 5 3.1 Deviation from standard ............................................................................................................ 5 3.2 Abnormalities from standard conditions .................................................................................... 5 3.3 Test Location ............................................................................................................................. 5 4 GENERAL INFORMATION ......................................................................................................................................... 6 4.1 Test frequencies ........................................................................................................................ 7 4.2 EUT Peripheral List ................................................................................................................... 8 4.3 Test Peripheral List ................................................................................................................... 8 4.4 TEST METHODOLOGY............................................................................................................ 9 4.5 Description of Test Modes ....................................................................................................... 10 5 EQUIPMENT USED DURING TEST ........................................................................................................................ 11 6 TEST RESULTS AND MEASUREMENT DATA .................................................................................................... 12 6.1 Antenna requirement .............................................................................................................. 12 6.2 Peak Power Measurement ...................................................................................................... 13 6.3 Frequency Separation and 20 dB Bandwidth .......................................................................... 15 6.4 Number of Hopping Frequency ............................................................................................... 17 6.5 Time of Occupancy (Dwell Time) ............................................................................................ 18 6.6 Conducted Spurious Emissions and Band Edges Test ........................................................... 20 6.7 Restrict-band Band-edge Measurements ............................................................................... 22 6.8 Radiated Emissions Measurement ......................................................................................... 24 6.9 Conducted Emissions ............................................................................................................. 34 6.10 Pseudorandom frequency hopping sequence ......................................................................... 37 7 TEST SETUP PHOTOGRAPHS OF EUT ................................................................................................................ 38 8 EXTERNAL PHOTOGRAPHS OF EUT ................................................................................................................... 38 9 INTERNAL PHOTOGRAPHS OF EUT .................................................................................................................... 38 Page 3 of 38 Report No.: AIT23010918W1 Dongguan Yaxu (AiT) Technolog…

Text truncated - open the document above for the full version.

add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 V150 天线规格 Antenna Specification Electrical Properties Frequency 2.4-2.5GHz Impedance50 Ohm Nominal V.S.W.R2.0 Max Gain 2.2 dBi RadiationOmni-directional PolarizationLinear Physical Properties ConnectorNA Cable TypeNA Cable LengthNA Cable ColorNA Operating Temp.-40 ~ +85 ̊C Storage Temp / Humidity 25±5 ̊C / <70% add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 Agilent E5071B S Parameter Test // BT Antenna add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 Passive Test For BT Freq (MHz) Effi (%) Effi (dB) Gain (dBi) 2400 48.1 -3.1 2.1 2410 48.9 -3.0 2.3 2420 49.0 -3.0 2.2 2430 49.0 -3.1 2.01 2440 49.4 -3.2 2.01 2450 49.8 -2.9 2.03 2460 49.8 -2.9 2.03 2470 49.8 -2.8 2.11 2480 49.9-2.8 2.1 2490 50 -2.7 2.1 2500 50-2.7 2.1 add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 Radiation Pattern For BT Antenna add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 Device add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086Fax:0769-82586086 BT Antenna

Dongguan Yaxu(AiT) Technology Limited Report No.: AIT23010918W1 FCC ID: WQ8-V150DC2241 Page 1 of 61 Appendix A RF Test Data for BT(BDR/EDR) (Conducted Measurement) Product Name: MaxiVCI V150 Trade Mark: AUTEL Test Model: MaxiVCI V150 Environmental Conditions Temperature: 25.2°C Relative Humidity: 52.4% ATM Pressure: 101Kpa Test Engineer: Simba Huang Supervised by: Seal Chen Dongguan Yaxu(AiT) Technology Limited Report No.: AIT23010918W1 FCC ID: WQ8-V150DC2241 Page 2 of 61 Contents Page COVER PAGE 1 Duty Cycle ........................................................................................................................................................................................... 3 1.1 Test Result ............................................................................................................................................................................... 3 1.2 Test Graphs ............................................................................................................................................................................. 4 2 Maximum Conducted Peak Output Power .......................................................................................................................................... 9 2.1 Test Result ............................................................................................................................................................................... 9 2.2 Test Graphs ........................................................................................................................................................................... 10 3 20dB Bandwidth ................................................................................................................................................................................ 15 3.1 Test Result ............................................................................................................................................................................. 15 3.2 Test Graphs ........................................................................................................................................................................... 16 4 Carrier Frequency Separation ........................................................................................................................................................... 21 4.1 Test Result ............................................................................................................................................................................. 21 4.2 Test Graphs ........................................................................................................................................................................... 22 5 Hopping Channel Number ................................................................................................................................................................. 24 5.1 Test Result ............................................................................................................................................................................. 24 5.2 Test Graphs ........................................................................................................................................................................... 25 6 Dwell Time ......................................................................................................................................................................................... 27 6.1 Test Result ............................................................................................................................................................................. 27 6.2 Test Graphs ........................................................................................................................................................................... 28 7 RF Conducted Spurious Emissions ................................................................................................................................................... 31 7.1 Test Result ............................................................................................................................................................................. 31 7.2 Test Graphs ........................................................................................................................................................................... 32 8 Band-edge for RF Conducted Emissions .......................................................................................................................................... 41 8.1 Test Result ............................................................................................................................................................................. 41 8.2 Test Graphs ........................................................................................................................................................................... 42 9 Restrict-band band-edge measurements .......................................................................................................................................... 54 9.1 Test Result ............................................................................................................................................................................. 54 9.2 Test Graphs ........................................................................................................................................................................... 56 Dongguan Yaxu(AiT) Technology Limited Report No.: AIT23010918W1 FCC ID: WQ8-V150DC2241 Page 3 of 61 1 Duty Cycle 1.1 Test Result Mode Frequency (MHz) Duty Cycle (%) 1/T (kHz) 1-DH1 2402 16.8 2.44 1-DH1 2441 16.8 2.44 1-DH1 2480 16.8 2.44 2-DH1 2402 17.2 2.38 2-DH1 2441 17.2 2.38 2-DH1 2480 17.2 2.38 3-DH1 2402 17.21 2.38 3-DH1 24…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Test Setup Photo Radiated Emission Page 2 of 2 FCC ID: WQ8-V150DC2241 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Conducted Emission ------End------