WQ8301SDCHD1Wireless Camera

i User Manual ii Trademark Autel ® X-Memo TM is the trademark of Autel Intelligent Technology Corp., Ltd., registered in China, the United States and other countries. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Autel. Disclaimer of Warranties and Limitation of Liabilities All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Autel reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given to the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Autel will not be liable for any direct damages or for any special, iii incidental, or indirect damages or for any economic consequential damages (including lost profits). IMPORTANT:Before operating or maintaining this unit, please read this manual carefully, paying extra attention to the safety warnings and precautions. Service Info http://pro.autel.com www.autel.com 1-855-288-3587/1-855-AUTELUS (North America) 0086-755-86147779 (China) [email protected] For technical assistance in all other markets, please contact your local selling agent. Safety Information iv Safety Information For your own safety and the safety of others, and to prevent damage to the X-memo camera, it is important that the safety instructions herein presented throughout this manual be read and understood by the user. Exercise caution when using the batteries. Batteries may leak or explode if products with batteries are not properly handled. Handle with extra care in the following situations to avoid a battery explosion or fire:  Do not use the camera or the battery if damage is observed - for example, if cracked, punctured or damaged by water.  Do not disassemble, bend or deform, puncture or shred.  Do not dry camera or battery with an external heat source such as hair dryer or microwave oven.  Do not put the camera or battery in damp environment. Secure the camera and battery with the provided housing.  Do not turn on the camera if it is wet. If the camera is already on, turn it off and remove the battery immediately. Allow the camera to dry thoroughly before use again.  Always use brand name or good quality charger to secure safe charging.  Apply to clean and smooth surface when attaching the adhesive Safety Information v mounts.  When operating the camera, always keep hands clean and dry.  If the camera is over heat, turn it off to cool down the camera. The safety messages herein cover situations Autel is aware of. Autel cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered do not jeopardize your personal safety. vi TRADEMARK ........................................................................... II COPYRIGHT INFORMATION ..................................................... II DISCLAIMER OF WARRANTIES AND LIMITATION OFLIABILITIES .. SAFETY INFORMATION ........................................................... IV CHAPTER 1 USING THIS MANUAL ......................................... 1 1.1 CONVENTIONS ............................................................ 1 1.1.1 Bold Text ......................................................................... 1 1.1.2 Terminology .................................................................... 1 1.1.3 Notes and Important Messages ..................................... 1 1.1.4 Hyperlinks ....................................................................... 2 1.1.5 Procedures ...................................................................... 2 CHAPTER 2 GENERAL INTRODUCTION .................................. 3 2.1 FUNCTIONAL DESCRIPTION ............................................. 3 2.1.1 LED Indicator Lights ........................................................ 6 2.2 POWER SOURCES ......................................................... 7 2.3 TECHNICAL SPECIFICATIONS ............................................ 8 2.4 ACCESSORIES KIT ......................................................... 9 CHAPTER 3 GETTING STARTED ............................................. 11 3.1 UNPACKING THE X‐MEMO ........................................... 11 3.2 USING THE MICROSD CARD ......................................... 11 3.2.1 Inserting the MicroSD Card .......................................... 12 3.2.2 Removing the MicroSD Card ......................................... 13 vii 3.3 USING THE BATTERY ................................................... 13 3.3.1 Inserting the Battery ..................................................... 13 3.3.2 Charging the Battery .................................................... 14 3.3.3 Using the Camera While Charging ............................... 14 3.4 ASSEMBLING THE MOUNTS .......................................... 15 3.5 POWERING UP .......................................................... 16 3.5.1 Screen Layouts .............................................................. 16 3.6 POWERING DOWNS .................................................... 18 CHAPTER 4 CAMERA OPERATIONS ....................................... 19 4.1 CAMERA DEFAULT SETTINGS ......................................... 19 4.2 CAMERA MODES ....................................................... 19 4.2.1 Video ............................................................................ 20 4.2.2 Photo ............................................................................ 21 4.2.3 Burst Photo ................................................................... 22 4.2.4 Time Lapse ...…

Text truncated - open the document above for the full version.

Autel Intelligent Tech. Corp., Ltd. 6th - 10th Floor, Bldg. B1, Zhiyuan, Xueyuan Rd., Xili,Nanshan, Shenzhen, China Tel: (86)755-86147779 FCC Authorization 1/6/2015 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Autel Intelligent Tech. Corp., Ltd. , the undersigned, hereby authorize Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Frank Li President QA-FR-170-B

Autel Intelligent Tech. Corp., Ltd. 6th - 10th Floor, Bldg. B1, Zhiyuan, Xueyuan Rd., Xili,Nanshan, Shenzhen, China Tel: (86)755-86147779 FCC Confidential Authorization 1/6/2015 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request regarding application for certification of FCC ID: WQ8301SDCHD1 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below:  Block Diagram--- (Long term)  Circuit Description--- (Long term)  Detailed Circuit Schematics of EUT--- (Long term) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely Yours, Signature: Frank Li President

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT – Front View EUT – Rear View EUT – Top View EUT – Bottom View EUT – Left Side View EUT – Right Side View

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT –Cover off View 1 EUT –Cover off View 2 EUT –Cover off View 3 EUT –Cover off View 4 EUT –Cover off View 5 EUT –Cover off View 6 EUT –Cover off View 7 EUT –Cover off View 8 EUT –Cover off View 9 EUT – Main Board Top View 1 EUT – Main Board Bottom View 1 EUT – Main Board Top View 2 EUT – Main Board Bottom View 2 EUT – Main Board Top View 3 EUT – Main Board Bottom View 3 EUT – LCD Top View EUT – LCD Bottom View EUT –Antenna View EUT –Battery Top View EUT –Battery Bottom View EUT –Antenna View Wifi Antenna

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. FCC PART 15, CLASS B TEST REPORT For Autel Intelligent Tech. Co., Ltd 6th-10th Floor, Building B1, Zhiyuan, Xueyuan Road, Xili, Nanshan, Shenzhen, 518055, China. FCC ID: WQ8301SDCHD1 Report Type: Original Report Product Type: Wireless Camera Test En gineer: William Li Re port Number: RSZ141203008-00A Re port Date: 2015-01-06 Reviewed B y: Jimmy Xiao RF En gineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ141203008-00A FCC Part 15, Class B Page 2 of 15 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST FACILITY ............................................................................................................................................................. 3 SYSTEM TEST CONFIGURATION .......................................................................................................................... 4 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 4 EUT EXERCISE SOFTWARE .......................................................................................................................................... 4 SPECIAL ACCESSORIES ................................................................................................................................................. 4 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 4 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 4 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 5 SUMMARY OF TEST RESULTS ............................................................................................................................... 6 FCC §15.107 – AC LINE CONDUCTED EMISSIONS ............................................................................................. 7 APPLICABLE STANDARD .............................................................................................................................................. 7 MEASUREMENT UNCERTAINTY .................................................................................................................................... 7 EUT SETUP .................................................................................................................................................................. 7 EMI TEST RECEIVER SETUP ......................................................................................................................................... 8 TEST PROCEDURE ........................................................................................................................................................ 8 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................................... 8 CORRECTED FACTOR & MARGIN CALCULATION ......................................................................................................... 8 TEST RESULTS SUMMARY ............................................................................................................................................ 9 TEST DATA .................................................................................................................................................................. 9 FCC §15.109 - RADIATED SPURIOUS EMISSIONS ............................................................................................ 12 APPLICABLE STANDARD ............................................................................................................................................ 12 MEASUREMENT UNCERTAINTY .................................................................................................................................. 12 EUT SETUP ................................................................................................................................................................ 12 EMI TEST RECEIVER SETUP ....................................................................................................................................... 13 TEST PROCEDURE ...................................................................................................................................................... 13 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 13 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View for Downloading mode Conducted Emissions - Side View for Downloading mode Radiated Emissions – Front View (Below 1 GHz for Downloading mode) Radiated Emissions – Rear View (Below 1 GHz for Downloading mode) Radiated Emissions – Front View (Above 1 GHz for Downloading mode) Radiated Emissions – Rear View (Above 1 GHz for Downloading mode) Radiated Emissions – Front View (Below 1 GHz for HDMI Playing mode) Radiated Emissions – Rear View (Below 1 GHz for HDMI Playing mode) Radiated Emissions – Front View (Above 1 GHz for HDMI Playing mode) Radiated Emissions – Rear View (Above 1 GHz for HDMI Playing mode)